Mini whip mf

Miniwhip Active Antenna HF LF VlF Mini Whip Shortwave SDR RX Portable Recei M ZH Description: MINIWHIP VLF LF HF ACTIVE ANTENNA.This is known PA0NHC newest design of MiniWhip Antenna. I have redesigned and built it on SMD components but the circuit diagram itself stayed the same as it had been described on his web page in open source. This sale includes the MiniWhip and Power Splitter assembled and tested boards. They go with its circuit diagrams and part list specification. No cables or connectors are included. This new version of PA0NHC MiniWhip Antenna has these features.New version, using modern BF998 and BCX54 semi conductors.Real class A circuitry, clean reception without IMD.One coax connection.Broadband R/C coupling to the receiver, no transformer For best signal-to-noise ratio:install the Miniwhip onto a well grounded mast.connect "GND" of the Miniwhip PCB to that mast.place HI-Ui ferrite cores (Ui bwtween 5000 and 10.000) on the beginning and end of all cables to block cable noise currents. Specifications: Frequency range: 10 KHz - 30 MHz Power: 12 - 15 volts at 150 mA Second order output intercept point: Greater than + 70 dBm Third order output intercept point: Greater than + 30 dBm Maximum output power: in excess of - 15 dBm PCB Size: Length (mm): As the picture show Connector: BNC Feed line: 50 - 100 ohm coaxial cable up to 100 meter long T o note please: Each antenna performs as good as its installation permits it to. Any active antenna is not working good inside the house! It should be mounted OUTSIDE and as high as possible. Place this MiniWhip antenna PCB inside suitable enclosure of your choise and mount outside the house. Probably for the enclosure you can use a piece of the PVC tube which available in varios diameters in a local store. Do not use metal enclosure! It wont work there! For max. sensitivity: this antenna should be positioned as high and free from meta Package include: 1Set Board Note:   The color might be a little different from the actual product due to color display of different monitors.  Please allow 1-3 cm error. Le 16-nov.-19 à 10:16:12 Paris, le vendeur a ajouté les informations suivantes:

Miniwhip Active Antenna MC LF VlF Mini Whip Shortwave SDR RX Portable Recei M ZH Description: MINIWHIP VLF LF HF ACTIVE ANTENNA.This is known PA0NHC newest design of MiniWhip Antenna. I have redesigned and built it on SMD components but the circuit diagram itself stayed the same as it had been described on his web page in open source. This sale includes the MiniWhip and Power Splitter assembled and tested boards. They go with its circuit diagrams and part list specification. No cables or connectors are included. This new version of PA0NHC MiniWhip Antenna has these features.New version, using modern BF998 and BCX54 semi conductors.Real class A circuitry, clean reception without IMD.One coax connection.Broadband R/C coupling to the receiver, no transformer For best signal-to-noise ratio:install the Miniwhip onto a well grounded mast.connect "GND" of the Miniwhip PCB to that mast.place HI-Ui ferrite cores (Ui bwtween 5000 and 10.000) on the beginning and end of all cables to block cable noise currents. Specifications: Frequency range: 10 KHz - 30 MHz Power: 12 - 15 volts at 150 mA Second order output intercept point: Greater than + 70 dBm Third order output intercept point: Greater than + 30 dBm Maximum output power: in excess of - 15 dBm PCB Size: Length (mm): As the picture show Connector: BNC Feed line: 50 - 100 ohm coaxial cable up to 100 meter long T o note please: Each antenna performs as good as its installation permits it to. Any active antenna is not working good inside the house! It should be mounted OUTSIDE and as high as possible. Place this MiniWhip antenna PCB inside suitable enclosure of your choise and mount outside the house. Probably for the enclosure you can use a piece of the PVC tube which available in varios diameters in a local store. Do not use metal enclosure! It wont work there! For max. sensitivity: this antenna should be positioned as high and free from meta Package include: 1Set Board Note:   The color might be a little different from the actual product due to color display of different monitors.  Please allow 1-3 cm error. Le 16-nov.-19 à 10:23:15 Paris, le vendeur a ajouté les informations suivantes:

Miniwhip Active Antenna MC LF VlF Mini Whip Shortwave SDR RX Portable Recei M ZH Description: MINIWHIP VLF LF HF ACTIVE ANTENNA.This is known PA0NHC newest design of MiniWhip Antenna. I have redesigned and built it on SMD components but the circuit diagram itself stayed the same as it had been described on his web page in open source. This sale includes the MiniWhip and Power Splitter assembled and tested boards. They go with its circuit diagrams and part list specification. No cables or connectors are included. This new version of PA0NHC MiniWhip Antenna has these features.New version, using modern BF998 and BCX54 semi conductors.Real class A circuitry, clean reception without IMD.One coax connection.Broadband R/C coupling to the receiver, no transformer For best signal-to-noise ratio:install the Miniwhip onto a well grounded mast.connect "GND" of the Miniwhip PCB to that mast.place HI-Ui ferrite cores (Ui bwtween 5000 and 10.000) on the beginning and end of all cables to block cable noise currents. Specifications: Frequency range: 10 KHz - 30 MHz Power: 12 - 15 volts at 150 mA Second order output intercept point: Greater than + 70 dBm Third order output intercept point: Greater than + 30 dBm Maximum output power: in excess of - 15 dBm PCB Size: Length (mm): As the picture show Connector: BNC Feed line: 50 - 100 ohm coaxial cable up to 100 meter long T o note please: Each antenna performs as good as its installation permits it to. Any active antenna is not working good inside the house! It should be mounted OUTSIDE and as high as possible. Place this MiniWhip antenna PCB inside suitable enclosure of your choise and mount outside the house. Probably for the enclosure you can use a piece of the PVC tube which available in varios diameters in a local store. Do not use metal enclosure! It wont work there! For max. sensitivity: this antenna should be positioned as high and free from meta Package include: 1Set Board Note:   The color might be a little different from the actual product due to color display of different monitors.  Please allow 1-3 cm error. Le 06-févr.-20 à 21:45:18 Paris, le vendeur a ajouté les informations suivantes:

Description: MINIWHIP VLF LF HF ACTIVE ANTENNA.This is known PA0NHC newest design of MiniWhip Antenna. I have redesigned and built it on SMD components but the circuit diagram itself stayed the same as it had been described on his web page in open source. This sale includes the MiniWhip and Power Splitter assembled and tested boards. They go with its circuit diagrams and part list specification. No cables or connectors are included. This new version of PA0NHC MiniWhip Antenna has these features.New version, using modern BF998 and BCX54 semi conductors.Real class A circuitry, clean reception without IMD.One coax connection.Broadband R/C coupling to the receiver, no transformer For best signal-to-noise ratio:install the Miniwhip onto a well grounded mast.connect "GND" of the Miniwhip PCB to that mast.place HI-Ui ferrite cores (Ui bwtween 5000 and 10.000) on the beginning and end of all cables to block cable noise currents. Specifications: Frequency range: 10 KHz - 30 MHz Power: 12 - 15 volts at 150 mA Second order output intercept point: Greater than + 70 dBm Third order output intercept point: Greater than + 30 dBm Maximum output power: in excess of - 15 dBm PCB Size: Length (mm): As the picture show Connector: BNC Feed line: 50 - 100 ohm coaxial cable up to 100 meter long T o note please: Each antenna performs as good as its installation permits it to. Any active antenna is not working good inside the house! It should be mounted OUTSIDE and as high as possible. Place this MiniWhip antenna PCB inside suitable enclosure of your choise and mount outside the house. Probably for the enclosure you can use a piece of the PVC tube which available in varios diameters in a local store. Do not use metal enclosure! It wont work there! For max. sensitivity: this antenna should be positioned as high and free from meta Package include: 1Set Board Note:   The color might be a little different from the actual product due to color display of different monitors.  Please allow 1-3 cm error. Le 02-nov.-19 à 04:55:03 Paris, le vendeur a ajouté les informations suivantes:

Description: MINIWHIP VLF LF HF ACTIVE ANTENNA.This is known PA0NHC newest design of MiniWhip Antenna. I have redesigned and built it on SMD components but the circuit diagram itself stayed the same as it had been described on his web page in open source. This sale includes the MiniWhip and Power Splitter assembled and tested boards. They go with its circuit diagrams and part list specification. No cables or connectors are included. This new version of PA0NHC MiniWhip Antenna has these features.New version, using modern BF998 and BCX54 semi conductors.Real class A circuitry, clean reception without IMD.One coax connection.Broadband R/C coupling to the receiver, no transformer For best signal-to-noise ratio:install the Miniwhip onto a well grounded mast.connect "GND" of the Miniwhip PCB to that mast.place HI-Ui ferrite cores (Ui bwtween 5000 and 10.000) on the beginning and end of all cables to block cable noise currents. Specifications: Frequency range: 10 KHz - 30 MHz Power: 12 - 15 volts at 150 mA Second order output intercept point: Greater than + 70 dBm Third order output intercept point: Greater than + 30 dBm Maximum output power: in excess of - 15 dBm PCB Size: Length (mm): As the picture show Connector: BNC Feed line: 50 - 100 ohm coaxial cable up to 100 meter long T o note please: Each antenna performs as good as its installation permits it to. Any active antenna is not working good inside the house! It should be mounted OUTSIDE and as high as possible. Place this MiniWhip antenna PCB inside suitable enclosure of your choise and mount outside the house. Probably for the enclosure you can use a piece of the PVC tube which available in varios diameters in a local store. Do not use metal enclosure! It wont work there! For max. sensitivity: this antenna should be positioned as high and free from meta Package include: 1Set Board Note:   The color might be a little different from the actual product due to color display of different monitors.  Please allow 1-3 cm error. Le 31-oct.-19 à 08:24:31 Paris, le vendeur a ajouté les informations suivantes:

Description: MINIWHIP VLF LF HF ACTIVE ANTENNA.This is known PA0NHC newest design of MiniWhip Antenna. I have redesigned and built it on SMD components but the circuit diagram itself stayed the same as it had been described on his web page in open source. This sale includes the MiniWhip and Power Splitter assembled and tested boards. They go with its circuit diagrams and part list specification. No cables or connectors are included. This new version of PA0NHC MiniWhip Antenna has these features.New version, using modern BF998 and BCX54 semi conductors.Real class A circuitry, clean reception without IMD.One coax connection.Broadband R/C coupling to the receiver, no transformer For best signal-to-noise ratio:install the Miniwhip onto a well grounded mast.connect "GND" of the Miniwhip PCB to that mast.place HI-Ui ferrite cores (Ui bwtween 5000 and 10.000) on the beginning and end of all cables to block cable noise currents. Specifications: Frequency range: 10 KHz - 30 MHz Power: 12 - 15 volts at 150 mA Second order output intercept point: Greater than + 70 dBm Third order output intercept point: Greater than + 30 dBm Maximum output power: in excess of - 15 dBm PCB Size: Length (mm): As the picture show Connector: BNC Feed line: 50 - 100 ohm coaxial cable up to 100 meter long T o note please: Each antenna performs as good as its installation permits it to. Any active antenna is not working good inside the house! It should be mounted OUTSIDE and as high as possible. Place this MiniWhip antenna PCB inside suitable enclosure of your choise and mount outside the house. Probably for the enclosure you can use a piece of the PVC tube which available in varios diameters in a local store. Do not use metal enclosure! It wont work there! For max. sensitivity: this antenna should be positioned as high and free from meta Package include: 1Set Board Note:   The color might be a little different from the actual product due to color display of different monitors.  Please allow 1-3 cm error. Le 18-nov.-19 à 18:30:46 Paris, le vendeur a ajouté les informations suivantes:

Description: MINIWHIP VLF LF HF ACTIVE ANTENNA.This is known PA0NHC newest design of MiniWhip Antenna. I have redesigned and built it on SMD components but the circuit diagram itself stayed the same as it had been described on his web page in open source. This sale includes the MiniWhip and Power Splitter assembled and tested boards. They go with its circuit diagrams and part list specification. No cables or connectors are included. This new version of PA0NHC MiniWhip Antenna has these features.New version, using modern BF998 and BCX54 semi conductors.Real class A circuitry, clean reception without IMD.One coax connection.Broadband R/C coupling to the receiver, no transformer For best signal-to-noise ratio:install the Miniwhip onto a well grounded mast.connect "GND" of the Miniwhip PCB to that mast.place HI-Ui ferrite cores (Ui bwtween 5000 and 10.000) on the beginning and end of all cables to block cable noise currents. Specifications: Frequency range: 10 KHz - 30 MHz Power: 12 - 15 volts at 150 mA Second order output intercept point: Greater than + 70 dBm Third order output intercept point: Greater than + 30 dBm Maximum output power: in excess of - 15 dBm PCB Size: Length (mm): As the picture show Connector: BNC Feed line: 50 - 100 ohm coaxial cable up to 100 meter long T o note please: Each antenna performs as good as its installation permits it to. Any active antenna is not working good inside the house! It should be mounted OUTSIDE and as high as possible. Place this MiniWhip antenna PCB inside suitable enclosure of your choise and mount outside the house. Probably for the enclosure you can use a piece of the PVC tube which available in varios diameters in a local store. Do not use metal enclosure! It wont work there! For max. sensitivity: this antenna should be positioned as high and free from meta Package include: 1Set Board Note:   The color might be a little different from the actual product due to color display of different monitors.  Please allow 1-3 cm error. Le 17-nov.-19 à 11:15:12 Paris, le vendeur a ajouté les informations suivantes:

Description: MINIWHIP VLF LF HF ACTIVE ANTENNA.This is known PA0NHC newest design of MiniWhip Antenna. I have redesigned and built it on SMD components but the circuit diagram itself stayed the same as it had been described on his web page in open source. This sale includes the MiniWhip and Power Splitter assembled and tested boards. They go with its circuit diagrams and part list specification. No cables or connectors are included. This new version of PA0NHC MiniWhip Antenna has these features.New version, using modern BF998 and BCX54 semi conductors.Real class A circuitry, clean reception without IMD.One coax connection.Broadband R/C coupling to the receiver, no transformer For best signal-to-noise ratio:install the Miniwhip onto a well grounded mast.connect "GND" of the Miniwhip PCB to that mast.place HI-Ui ferrite cores (Ui bwtween 5000 and 10.000) on the beginning and end of all cables to block cable noise currents. Specifications: Frequency range: 10 KHz - 30 MHz Power: 12 - 15 volts at 150 mA Second order output intercept point: Greater than + 70 dBm Third order output intercept point: Greater than + 30 dBm Maximum output power: in excess of - 15 dBm PCB Size: Length (mm): As the picture show Connector: BNC Feed line: 50 - 100 ohm coaxial cable up to 100 meter long T o note please: Each antenna performs as good as its installation permits it to. Any active antenna is not working good inside the house! It should be mounted OUTSIDE and as high as possible. Place this MiniWhip antenna PCB inside suitable enclosure of your choise and mount outside the house. Probably for the enclosure you can use a piece of the PVC tube which available in varios diameters in a local store. Do not use metal enclosure! It wont work there! For max. sensitivity: this antenna should be positioned as high and free from meta Package include: 1Set Board Note:   The color might be a little different from the actual product due to color display of different monitors.  Please allow 1-3 cm error. Le 21-nov.-19 à 15:16:08 Paris, le vendeur a ajouté les informations suivantes:

Description: MINIWHIP VLF LF HF ACTIVE ANTENNA.This is known PA0NHC newest design of MiniWhip Antenna. I have redesigned and built it on SMD components but the circuit diagram itself stayed the same as it had been described on his web page in open source. This sale includes the MiniWhip and Power Splitter assembled and tested boards. They go with its circuit diagrams and part list specification. No cables or connectors are included. This new version of PA0NHC MiniWhip Antenna has these features.New version, using modern BF998 and BCX54 semi conductors.Real class A circuitry, clean reception without IMD.One coax connection.Broadband R/C coupling to the receiver, no transformer For best signal-to-noise ratio:install the Miniwhip onto a well grounded mast.connect "GND" of the Miniwhip PCB to that mast.place HI-Ui ferrite cores (Ui bwtween 5000 and 10.000) on the beginning and end of all cables to block cable noise currents. Specifications: Frequency range: 10 KHz - 30 MHz Power: 12 - 15 volts at 150 mA Second order output intercept point: Greater than + 70 dBm Third order output intercept point: Greater than + 30 dBm Maximum output power: in excess of - 15 dBm PCB Size: Length (mm): As the picture show Connector: BNC Feed line: 50 - 100 ohm coaxial cable up to 100 meter long T o note please: Each antenna performs as good as its installation permits it to. Any active antenna is not working good inside the house! It should be mounted OUTSIDE and as high as possible. Place this MiniWhip antenna PCB inside suitable enclosure of your choise and mount outside the house. Probably for the enclosure you can use a piece of the PVC tube which available in varios diameters in a local store. Do not use metal enclosure! It wont work there! For max. sensitivity: this antenna should be positioned as high and free from meta Package include: 1Set Board Note:   The color might be a little different from the actual product due to color display of different monitors.  Please allow 1-3 cm error. Le 19-déc.-19 à 03:27:15 Paris, le vendeur a ajouté les informations suivantes:

Description: MINIWHIP VLF LF HF ACTIVE ANTENNA.This is known PA0NHC newest design of MiniWhip Antenna. I have redesigned and built it on SMD components but the circuit diagram itself stayed the same as it had been described on his web page in open source. This sale includes the MiniWhip and Power Splitter assembled and tested boards. They go with its circuit diagrams and part list specification. No cables or connectors are included. This new version of PA0NHC MiniWhip Antenna has these features.New version, using modern BF998 and BCX54 semi conductors.Real class A circuitry, clean reception without IMD.One coax connection.Broadband R/C coupling to the receiver, no transformer For best signal-to-noise ratio:install the Miniwhip onto a well grounded mast.connect "GND" of the Miniwhip PCB to that mast.place HI-Ui ferrite cores (Ui bwtween 5000 and 10.000) on the beginning and end of all cables to block cable noise currents. Specifications: Frequency range: 10 KHz - 30 MHz Power: 12 - 15 volts at 150 mA Second order output intercept point: Greater than + 70 dBm Third order output intercept point: Greater than + 30 dBm Maximum output power: in excess of - 15 dBm PCB Size: Length (mm): As the picture show Connector: BNC Feed line: 50 - 100 ohm coaxial cable up to 100 meter long T o note please: Each antenna performs as good as its installation permits it to. Any active antenna is not working good inside the house! It should be mounted OUTSIDE and as high as possible. Place this MiniWhip antenna PCB inside suitable enclosure of your choise and mount outside the house. Probably for the enclosure you can use a piece of the PVC tube which available in varios diameters in a local store. Do not use metal enclosure! It wont work there! For max. sensitivity: this antenna should be positioned as high and free from meta Package include: 1Set Board Note:   The color might be a little different from the actual product due to color display of different monitors.  Please allow 1-3 cm error. Le 11-mars-20 à 13:30:27 Paris, le vendeur a ajouté les informations suivantes:

Description: MINIWHIP VLF LF HF ACTIVE ANTENNA.This is known PA0NHC newest design of MiniWhip Antenna. I have redesigned and built it on SMD components but the circuit diagram itself stayed the same as it had been described on his web page in open source. This sale includes the MiniWhip and Power Splitter assembled and tested boards. They go with its circuit diagrams and part list specification. No cables or connectors are included. This new version of PA0NHC MiniWhip Antenna has these features.New version, using modern BF998 and BCX54 semi conductors.Real class A circuitry, clean reception without IMD.One coax connection.Broadband R/C coupling to the receiver, no transformer For best signal-to-noise ratio:install the Miniwhip onto a well grounded mast.connect "GND" of the Miniwhip PCB to that mast.place HI-Ui ferrite cores (Ui bwtween 5000 and 10.000) on the beginning and end of all cables to block cable noise currents. Specifications: Frequency range: 10 KHz - 30 MHz Power: 12 - 15 volts at 150 mA Second order output intercept point: Greater than + 70 dBm Third order output intercept point: Greater than + 30 dBm Maximum output power: in excess of - 15 dBm PCB Size: Length (mm): As the picture show Connector: BNC Feed line: 50 - 100 ohm coaxial cable up to 100 meter long T o note please: Each antenna performs as good as its installation permits it to. Any active antenna is not working good inside the house! It should be mounted OUTSIDE and as high as possible. Place this MiniWhip antenna PCB inside suitable enclosure of your choise and mount outside the house. Probably for the enclosure you can use a piece of the PVC tube which available in varios diameters in a local store. Do not use metal enclosure! It wont work there! For max. sensitivity: this antenna should be positioned as high and free from meta Package include: 1Set Board Note:   The color might be a little different from the actual product due to color display of different monitors.  Please allow 1-3 cm error. Le 04-avr.-20 à 15:50:26 Paris, le vendeur a ajouté les informations suivantes:

logiciel iOS 9.3.5 Nom: MF 432LL/A A 1432 N° série F7NN1P4SFP84 16GO h:200mm l:134,7mm ép: 7,2mm poids: 308gr Processeur: A5 bicoeur Photo av 5Mpx-ar1,2Mpx Wifi mini jack 1ère main très soigneuse- housse de protection - câble USB avec chargeur En parfait état de marche Remplacement pour plus de GO DISPONIBLE APRÈS NOEL 2020 - Prix à débattre Téléphones et tablettes occasion à vendre à Pessat-Villeneuve (63200)

2.0 MP Capteur de l'appareil photo principal 2.5G Réseau 2,4''Écran Type de carte mémoire pour extension: Micro SD Connectivité de base Type de carte SIM: Mini SIM Connecteurs AV: Connecteur AV Nokia 3.5 mm Connecteur de charge: Connecteur pour chargeur 2.0 mm Connecteur système: Micro-USB-B USB: USB 2.0 Bluetooth: Bluetooth 2.1 + EDR Profils Bluetooth: Profil d'accès SIM (SAP), Profil d'application découverte de service (SDAP), HFP *, HSP *, OPP * WiFi: WLAN IEEE 802.11 b/g Vidéo et audio Formats de fichiers audio: AAC, AMR, AU, M4A, MF, MIDI, MP3, MP4, Wav, WMA Codecs de lecture audio: AAC-LC, AMR-NB, AMR-WB, HE-AAC, HE-AACv2, MIDI, MP3, XMF Mobile, RealAudio 8, SP-MIDI, WMA 10, WMA 10 Pro, WMA 9 Formats de fichiers d'enregistrement audio: AAC, Wav Codecs d'enregistrement audio: AMR-NB Fonctionnalités de la radio: Radio stéréo FM, Radio FM RDS Contenu du coffret Nokia C3-00 Chargeur compact Nokia AC-3 Batterie Nokia BL-5J Kit oreillette stéréo Nokia WH-102 Guide rapide, Manuel d'utilisation et Brochure d'information produit 50,00 € plus frais de poste 8,00 € environs - 06

JUSTE SERVI POUR ESSAIS SDR Faible bruit R820T2 RTL2832U +Ham it UP V1.3 0.5- 50MHZ Nooelec. État : Occasion Faible bruit R820T2 RTL2832U USB RTL-SDR avec Quartz & METAL CASE-thumbnet N3 Thumbnet have taken the ubiquitous RTL-SDR back to the drawing board and started again from scratch, optimizing everything for weak-signal reception!     Full compatibility with existing RTL-SDR software - HDSDR, SDR# etc.     High stability +/-0.5ppm TCXO for accurate, rock-solid tuning     Standard R820T2 + RTL2832U plus 24C02 EEPROM chipset     Improved/enhanced decoupling including common-mode choke on USB port     Low-noise, linear 3.3V and 1.2V voltage regulators     Connector for optional external DC +5V supply with matching plug included     Mini-USB B connection - screened and filtered cable included     F type RF connector - BNC adapter included     6x4cm contiguous ground-plane for better thermal dissipation     Static drain-away resistor on the RF input     All unnecessary parts eliminated to reduce parts count and noise     Extruded aluminium case with additional internal screening can     Case external dimensions 62 x 41 x 23mm excluding connectors Included in the package:     Thumbnet N3 USB RTL-SDR     DC power plug with screw terminals     BNC female to F type male antenna adapter     Screened mini USB to twin USB high current 'Y' cable Ham It Up' - RF Convertisseur Pour SDRs RTL2832U E4000 & R820T; MF/HF Converter Nooelec Boitier pour converter SDR HF Nooelec Ham It Up

Manual user: https://www.manualslib.com/manual/708501/Yaesu-Frg-9600.html        FRG-9600 Specifications FREQUENCY RANGE AM/FM Modes 60-905 MHz SSB Mode 60-460 MHz CHANNELS Channels 100 Banks 10 (10 channels each) TUNING STEPS FM-N 5/10/12.5/25 kHz FM-W 100 kHz AM-N 100 Hz/1 kHz AM-W 5/10/12.5/25 kHz SSB 100 Hz/1 kHz BANDWIDTHS FM-N 15 kHz FM-W 180 kHz AM-N 2.4 kHz AM-W 6 kHz SSB 2.4 kHz EXTERNAL JACKS Antenna SO-239 External Earphone Mini (3.5 mm) Power Input Center Positive (13.8 VDC) Recorder Activation     RCA Phono Mute RCA Phono Band Data 4 Pin CAT DIN GENERAL Audio Output Maximum 1 watts (nominal) 8 ohms IF Frequencies 47.754 MHz, 10.7 MHz, 455 kHz Internal Speaker 8 Ohms Power Requirement PA-4B 117 VAC Adapter or 13.8 VDC 550 mA Antenna Telescopic whip antenna included Size (180x80x220mm 2.2 kg)     Très bon état de marche, avec alimentation 13,8 volts et antenne.