4a module state

1. Introduction   This FM stereo digital radio circuit board module has built-in DSP digital noise processing. When there is no signal, it will automatically mute and get rid of the noise of the traditional FM radio.   2.   Parameter   NO. Parameter Value 1 Output power 500mW (drive earphone), 3Wx2 (drive horn) 2 Frequency range 50Hz-18KHz  3 Receiving frequency range 87.0MHz-108.0MHz 4 Equivalent noise Greater than 30dB 5 Power supply voltage 3.0V-5.0V 6 Power supply current 1000mA at maximum volume, 60mA at minimum volume (for reference only) 7 Sound track Stereo       3. Using attention:   1>. The power supply voltage is strictly prohibited to exceed the power supply voltage range of this module. 2>. Do not touch the back part of the module when working, so as not to affect the normal work of this module or cause the short-circuit burn module.   4. Feature   1>. Advanced digital audio signal processing technology (DSP) and FM phase-locked loop modulation (PLL) make the sound quality more realistic, more stable performance, and long working frequency without deviation. 2>. LCD display is more intuitive and accurate, with extremely low power consumption and minimal noise interference. 3>. 30 digital volume adjustment, with buttons, easy to operate. 4>. Automatically storage data before power off. 5>. Automatic switch of speaker/headphone output. 6>. Quartz crystal steady frequency, temperature change reception frequency, no longer drift. 7>. It uses professional audio DSP to analyze and process the audio signal, and automatically mute when there is no signal or weak signal. 8>. It uses incremental digital rotary encoder to adjust the volume and frequency, using the feel is good, positioning accuracy, stable and durable, 360 ° rotating without blind Angle. 9> Support serial communication control, available computer or MCU and other devices with serial ports to control all functions of the module.   5. Instruction   1>. Power supply Module corresponding port (marked on PCB board). “-” and “+” are the anode and cathode of the power (battery). The power supply is recommended for battery or other stabilized power supply.You cannot use a power supply without filter (such as mobile phone charger, mobile power supply, and other switching power supply), otherwise the interference caused by power supply will affect the normal work of this module. The normal working voltage of this module is 3.0-5.0V, not exceeding this range. At the maximum volume of the module, the maximum power supply current is around 1A, which requires the battery to output enough current. 2>. Antenna The FM_ANT port is used to connect the FM antenna. To better receive the FM signal, it is recommended to extend the antenna with a length of 75cm. 3>. Headset/speaker output This module is with 3WX2 channel audio amplifier. If the horn is needed, access the speaker port. It is recommended to use 4 Ω / 3 w speakers.If the headset is inserted, the audio will automatically switch to the headphone channel, and the speaker channel will be closed automatically. 4>. Volume Turn the VOL encoder to adjust the volume, while the LCD screen displays the volume series. 5>. Frequency regulation Turn the FRE encoder to adjust the reception frequency, while the LCD screen displays the current frequency, and press the encoder handle to the mute/non-mute switch. 6>. Mute Press the VOL knob to switch the mute/non-mute button down. 7>. AMCAP switch Long press the FRE knob to switch on or off the AMCAP, the LCD display subtitle ON means to turn on the AMCAP, and OFF means to turn off the AMCAP. 8>. AMCAP threshold adjustment(when the AMCAP switch on) Short press the FRE knob to AMCAP threshold adjustment interface, you can adjust the movement threshold of the AMCAP according to the specific usage situation. The adjustment range is 0-20. The higher the value is, the higher the threshold is, the easier the weak signal is to be silent. Vice versa. 9>. Serial port (without serial port control) The module reserved TTL level serial port control interface. TTL serial port and this module communication need to connect the module's UART_RX, UART_TX and GND (the corresponding position of PCB is marked). You can use the external MCU or the computer serial port to send the command control module related functions. Note: because the computer serial port is not TTL level, connect the computer communication, it is necessary to connect the RS323 level to TTL power leveling device or the USB TTL level serial port module to communicate with this module. This operation requires professionals. 10>. User Settings This module can set the backlight state according to the user's specific usage. When the power is off, press the FRE button to turn on, and the B0 indicates that the backlight is always bright. B0 indicates that the backlight is closed for 20 seconds, and the setting is effective after the restart. Change the Settings state to repeat this step to switch. The backlight has no operation for 20 seconds. 11>. Stereo /mono switch terminal. Stereo/mono terminals are used to set the FM receiving mode of the module. This terminal is suspended for Stereo reception mode, and it is a single channel receiving mode.   6. FM with squelch receiver module AT instruction: Baud rate: 38400 TTL level   No. Name Example Instruction Range Return position 1 Set current frequency point AT+FRE=875 current frequency point is 87.5MHz  870-1080 MHz Current frequency point/ERR 2 Frequency point-0.1MHZ AT+FRED     Current frequency point   Le 10-juil.-19 à 05:53:17 Paris, le vendeur a ajouté les informations suivantes:

1. Introduction   This FM stereo digital radio circuit board module has built-in DSP digital noise processing. When there is no signal, it will automatically mute and get rid of the noise of the traditional FM radio.   2.   Parameter   NO. Parameter Value 1 Output power 500mW (drive earphone), 3Wx2 (drive horn) 2 Frequency range 50Hz-18KHz  3 Receiving frequency range 87.0MHz-108.0MHz 4 Equivalent noise Greater than 30dB 5 Power supply voltage 3.0V-5.0V 6 Power supply current 1000mA at maximum volume, 60mA at minimum volume (for reference only) 7 Sound track Stereo       3. Using attention:   1>. The power supply voltage is strictly prohibited to exceed the power supply voltage range of this module. 2>. Do not touch the back part of the module when working, so as not to affect the normal work of this module or cause the short-circuit burn module.   4. Feature   1>. Advanced digital audio signal processing technology (DSP) and FM phase-locked loop modulation (PLL) make the sound quality more realistic, more stable performance, and long working frequency without deviation. 2>. LCD display is more intuitive and accurate, with extremely low power consumption and minimal noise interference. 3>. 30 digital volume adjustment, with buttons, easy to operate. 4>. Automatically storage data before power off. 5>. Automatic switch of speaker/headphone output. 6>. Quartz crystal steady frequency, temperature change reception frequency, no longer drift. 7>. It uses professional audio DSP to analyze and process the audio signal, and automatically mute when there is no signal or weak signal. 8>. It uses incremental digital rotary encoder to adjust the volume and frequency, using the feel is good, positioning accuracy, stable and durable, 360 ° rotating without blind Angle. 9> Support serial communication control, available computer or MCU and other devices with serial ports to control all functions of the module.   5. Instruction   1>. Power supply Module corresponding port (marked on PCB board). “-” and “+” are the anode and cathode of the power (battery). The power supply is recommended for battery or other stabilized power supply.You cannot use a power supply without filter (such as mobile phone charger, mobile power supply, and other switching power supply), otherwise the interference caused by power supply will affect the normal work of this module. The normal working voltage of this module is 3.0-5.0V, not exceeding this range. At the maximum volume of the module, the maximum power supply current is around 1A, which requires the battery to output enough current. 2>. Antenna The FM_ANT port is used to connect the FM antenna. To better receive the FM signal, it is recommended to extend the antenna with a length of 75cm. 3>. Headset/speaker output This module is with 3WX2 channel audio amplifier. If the horn is needed, access the speaker port. It is recommended to use 4 Ω / 3 w speakers.If the headset is inserted, the audio will automatically switch to the headphone channel, and the speaker channel will be closed automatically. 4>. Volume Turn the VOL encoder to adjust the volume, while the LCD screen displays the volume series. 5>. Frequency regulation Turn the FRE encoder to adjust the reception frequency, while the LCD screen displays the current frequency, and press the encoder handle to the mute/non-mute switch. 6>. Mute Press the VOL knob to switch the mute/non-mute button down. 7>. AMCAP switch Long press the FRE knob to switch on or off the AMCAP, the LCD display subtitle ON means to turn on the AMCAP, and OFF means to turn off the AMCAP. 8>. AMCAP threshold adjustment(when the AMCAP switch on) Short press the FRE knob to AMCAP threshold adjustment interface, you can adjust the movement threshold of the AMCAP according to the specific usage situation. The adjustment range is 0-20. The higher the value is, the higher the threshold is, the easier the weak signal is to be silent. Vice versa. 9>. Serial port (without serial port control) The module reserved TTL level serial port control interface. TTL serial port and this module communication need to connect the module's UART_RX, UART_TX and GND (the corresponding position of PCB is marked). You can use the external MCU or the computer serial port to send the command control module related functions. Note: because the computer serial port is not TTL level, connect the computer communication, it is necessary to connect the RS323 level to TTL power leveling device or the USB TTL level serial port module to communicate with this module. This operation requires professionals. 10>. User Settings This module can set the backlight state according to the user's specific usage. When the power is off, press the FRE button to turn on, and the B0 indicates that the backlight is always bright. B0 indicates that the backlight is closed for 20 seconds, and the setting is effective after the restart. Change the Settings state to repeat this step to switch. The backlight has no operation for 20 seconds. 11>. Stereo /mono switch terminal. Stereo/mono terminals are used to set the FM receiving mode of the module. This terminal is suspended for Stereo reception mode, and it is a single channel receiving mode.   6. FM with squelch receiver module AT instruction: Baud rate: 38400 TTL level   No. Name Example Instruction Range Return position 1 Set current frequency point AT+FRE=875 current frequency point is 87.5MHz  870-1080 MHz Current frequency point/ERR 2 Frequency point-0.1MHZ AT+FRED     Current frequency point   Le 09-juil.-19 à 17:37:11 Paris, le vendeur a ajouté les informations suivantes:

1. Introduction   This FM stereo digital radio circuit board module has built-in DSP digital noise processing. When there is no signal, it will automatically mute and get rid of the noise of the traditional FM radio.   2.   Parameter   NO. Parameter Value 1 Output power 500mW (drive earphone), 3Wx2 (drive horn) 2 Frequency range 50Hz-18KHz  3 Receiving frequency range 87.0MHz-108.0MHz 4 Equivalent noise Greater than 30dB 5 Power supply voltage 3.0V-5.0V 6 Power supply current 1000mA at maximum volume, 60mA at minimum volume (for reference only) 7 Sound track Stereo       3. Using attention:   1>. The power supply voltage is strictly prohibited to exceed the power supply voltage range of this module. 2>. Do not touch the back part of the module when working, so as not to affect the normal work of this module or cause the short-circuit burn module.   4. Feature   1>. Advanced digital audio signal processing technology (DSP) and FM phase-locked loop modulation (PLL) make the sound quality more realistic, more stable performance, and long working frequency without deviation. 2>. LCD display is more intuitive and accurate, with extremely low power consumption and minimal noise interference. 3>. 30 digital volume adjustment, with buttons, easy to operate. 4>. Automatically storage data before power off. 5>. Automatic switch of speaker/headphone output. 6>. Quartz crystal steady frequency, temperature change reception frequency, no longer drift. 7>. It uses professional audio DSP to analyze and process the audio signal, and automatically mute when there is no signal or weak signal. 8>. It uses incremental digital rotary encoder to adjust the volume and frequency, using the feel is good, positioning accuracy, stable and durable, 360 ° rotating without blind Angle. 9> Support serial communication control, available computer or MCU and other devices with serial ports to control all functions of the module.   5. Instruction   1>. Power supply Module corresponding port (marked on PCB board). “-” and “+” are the anode and cathode of the power (battery). The power supply is recommended for battery or other stabilized power supply.You cannot use a power supply without filter (such as mobile phone charger, mobile power supply, and other switching power supply), otherwise the interference caused by power supply will affect the normal work of this module. The normal working voltage of this module is 3.0-5.0V, not exceeding this range. At the maximum volume of the module, the maximum power supply current is around 1A, which requires the battery to output enough current. 2>. Antenna The FM_ANT port is used to connect the FM antenna. To better receive the FM signal, it is recommended to extend the antenna with a length of 75cm. 3>. Headset/speaker output This module is with 3WX2 channel audio amplifier. If the horn is needed, access the speaker port. It is recommended to use 4 Ω / 3 w speakers.If the headset is inserted, the audio will automatically switch to the headphone channel, and the speaker channel will be closed automatically. 4>. Volume Turn the VOL encoder to adjust the volume, while the LCD screen displays the volume series. 5>. Frequency regulation Turn the FRE encoder to adjust the reception frequency, while the LCD screen displays the current frequency, and press the encoder handle to the mute/non-mute switch. 6>. Mute Press the VOL knob to switch the mute/non-mute button down. 7>. AMCAP switch Long press the FRE knob to switch on or off the AMCAP, the LCD display subtitle ON means to turn on the AMCAP, and OFF means to turn off the AMCAP. 8>. AMCAP threshold adjustment(when the AMCAP switch on) Short press the FRE knob to AMCAP threshold adjustment interface, you can adjust the movement threshold of the AMCAP according to the specific usage situation. The adjustment range is 0-20. The higher the value is, the higher the threshold is, the easier the weak signal is to be silent. Vice versa. 9>. Serial port (without serial port control) The module reserved TTL level serial port control interface. TTL serial port and this module communication need to connect the module's UART_RX, UART_TX and GND (the corresponding position of PCB is marked). You can use the external MCU or the computer serial port to send the command control module related functions. Note: because the computer serial port is not TTL level, connect the computer communication, it is necessary to connect the RS323 level to TTL power leveling device or the USB TTL level serial port module to communicate with this module. This operation requires professionals. 10>. User Settings This module can set the backlight state according to the user's specific usage. When the power is off, press the FRE button to turn on, and the B0 indicates that the backlight is always bright. B0 indicates that the backlight is closed for 20 seconds, and the setting is effective after the restart. Change the Settings state to repeat this step to switch. The backlight has no operation for 20 seconds. 11>. Stereo /mono switch terminal. Stereo/mono terminals are used to set the FM receiving mode of the module. This terminal is suspended for Stereo reception mode, and it is a single channel receiving mode.   6. FM with squelch receiver module AT instruction: Baud rate: 38400 TTL level   No. Name Example Instruction Range Return position 1 Set current frequency point AT+FRE=875 current frequency point is 87.5MHz  870-1080 MHz Current frequency point/ERR 2 Frequency point-0.1MHZ AT+FRED     Current frequency point   Le 08-juil.-19 à 15:14:31 Paris, le vendeur a ajouté les informations suivantes:

1. Introduction   This FM stereo digital radio circuit board module has built-in DSP digital noise processing. When there is no signal, it will automatically mute and get rid of the noise of the traditional FM radio.   2.   Parameter   NO. Parameter Value 1 Output power 500mW (drive earphone), 3Wx2 (drive horn) 2 Frequency range 50Hz-18KHz  3 Receiving frequency range 87.0MHz-108.0MHz 4 Equivalent noise Greater than 30dB 5 Power supply voltage 3.0V-5.0V 6 Power supply current 1000mA at maximum volume, 60mA at minimum volume (for reference only) 7 Sound track Stereo       3. Using attention:   1>. The power supply voltage is strictly prohibited to exceed the power supply voltage range of this module. 2>. Do not touch the back part of the module when working, so as not to affect the normal work of this module or cause the short-circuit burn module.   4. Feature   1>. Advanced digital audio signal processing technology (DSP) and FM phase-locked loop modulation (PLL) make the sound quality more realistic, more stable performance, and long working frequency without deviation. 2>. LCD display is more intuitive and accurate, with extremely low power consumption and minimal noise interference. 3>. 30 digital volume adjustment, with buttons, easy to operate. 4>. Automatically storage data before power off. 5>. Automatic switch of speaker/headphone output. 6>. Quartz crystal steady frequency, temperature change reception frequency, no longer drift. 7>. It uses professional audio DSP to analyze and process the audio signal, and automatically mute when there is no signal or weak signal. 8>. It uses incremental digital rotary encoder to adjust the volume and frequency, using the feel is good, positioning accuracy, stable and durable, 360 ° rotating without blind Angle. 9> Support serial communication control, available computer or MCU and other devices with serial ports to control all functions of the module.   5. Instruction   1>. Power supply Module corresponding port (marked on PCB board). “-” and “+” are the anode and cathode of the power (battery). The power supply is recommended for battery or other stabilized power supply.You cannot use a power supply without filter (such as mobile phone charger, mobile power supply, and other switching power supply), otherwise the interference caused by power supply will affect the normal work of this module. The normal working voltage of this module is 3.0-5.0V, not exceeding this range. At the maximum volume of the module, the maximum power supply current is around 1A, which requires the battery to output enough current. 2>. Antenna The FM_ANT port is used to connect the FM antenna. To better receive the FM signal, it is recommended to extend the antenna with a length of 75cm. 3>. Headset/speaker output This module is with 3WX2 channel audio amplifier. If the horn is needed, access the speaker port. It is recommended to use 4 Ω / 3 w speakers.If the headset is inserted, the audio will automatically switch to the headphone channel, and the speaker channel will be closed automatically. 4>. Volume Turn the VOL encoder to adjust the volume, while the LCD screen displays the volume series. 5>. Frequency regulation Turn the FRE encoder to adjust the reception frequency, while the LCD screen displays the current frequency, and press the encoder handle to the mute/non-mute switch. 6>. Mute Press the VOL knob to switch the mute/non-mute button down. 7>. AMCAP switch Long press the FRE knob to switch on or off the AMCAP, the LCD display subtitle ON means to turn on the AMCAP, and OFF means to turn off the AMCAP. 8>. AMCAP threshold adjustment(when the AMCAP switch on) Short press the FRE knob to AMCAP threshold adjustment interface, you can adjust the movement threshold of the AMCAP according to the specific usage situation. The adjustment range is 0-20. The higher the value is, the higher the threshold is, the easier the weak signal is to be silent. Vice versa. 9>. Serial port (without serial port control) The module reserved TTL level serial port control interface. TTL serial port and this module communication need to connect the module's UART_RX, UART_TX and GND (the corresponding position of PCB is marked). You can use the external MCU or the computer serial port to send the command control module related functions. Note: because the computer serial port is not TTL level, connect the computer communication, it is necessary to connect the RS323 level to TTL power leveling device or the USB TTL level serial port module to communicate with this module. This operation requires professionals. 10>. User Settings This module can set the backlight state according to the user's specific usage. When the power is off, press the FRE button to turn on, and the B0 indicates that the backlight is always bright. B0 indicates that the backlight is closed for 20 seconds, and the setting is effective after the restart. Change the Settings state to repeat this step to switch. The backlight has no operation for 20 seconds. 11>. Stereo /mono switch terminal. Stereo/mono terminals are used to set the FM receiving mode of the module. This terminal is suspended for Stereo reception mode, and it is a single channel receiving mode.   6. FM with squelch receiver module AT instruction: Baud rate: 38400 TTL level   No. Name Example Instruction Range Return position 1 Set current frequency point AT+FRE=875 current frequency point is 87.5MHz  870-1080 MHz Current frequency point/ERR 2 Frequency point-0.1MHZ AT+FRED     Current frequency point   Le 10-août-19 à 10:14:47 Paris, le vendeur a ajouté les informations suivantes:

1. Introduction   This FM stereo digital radio circuit board module has built-in DSP digital noise processing. When there is no signal, it will automatically mute and get rid of the noise of the traditional FM radio.   2.   Parameter   NO. Parameter Value 1 Output power 500mW (drive earphone), 3Wx2 (drive horn) 2 Frequency range 50Hz-18KHz  3 Receiving frequency range 87.0MHz-108.0MHz 4 Equivalent noise Greater than 30dB 5 Power supply voltage 3.0V-5.0V 6 Power supply current 1000mA at maximum volume, 60mA at minimum volume (for reference only) 7 Sound track Stereo       3. Using attention:   1>. The power supply voltage is strictly prohibited to exceed the power supply voltage range of this module. 2>. Do not touch the back part of the module when working, so as not to affect the normal work of this module or cause the short-circuit burn module.   4. Feature   1>. Advanced digital audio signal processing technology (DSP) and FM phase-locked loop modulation (PLL) make the sound quality more realistic, more stable performance, and long working frequency without deviation. 2>. LCD display is more intuitive and accurate, with extremely low power consumption and minimal noise interference. 3>. 30 digital volume adjustment, with buttons, easy to operate. 4>. Automatically storage data before power off. 5>. Automatic switch of speaker/headphone output. 6>. Quartz crystal steady frequency, temperature change reception frequency, no longer drift. 7>. It uses professional audio DSP to analyze and process the audio signal, and automatically mute when there is no signal or weak signal. 8>. It uses incremental digital rotary encoder to adjust the volume and frequency, using the feel is good, positioning accuracy, stable and durable, 360 ° rotating without blind Angle. 9> Support serial communication control, available computer or MCU and other devices with serial ports to control all functions of the module.   5. Instruction   1>. Power supply Module corresponding port (marked on PCB board). “-” and “+” are the anode and cathode of the power (battery). The power supply is recommended for battery or other stabilized power supply.You cannot use a power supply without filter (such as mobile phone charger, mobile power supply, and other switching power supply), otherwise the interference caused by power supply will affect the normal work of this module. The normal working voltage of this module is 3.0-5.0V, not exceeding this range. At the maximum volume of the module, the maximum power supply current is around 1A, which requires the battery to output enough current. 2>. Antenna The FM_ANT port is used to connect the FM antenna. To better receive the FM signal, it is recommended to extend the antenna with a length of 75cm. 3>. Headset/speaker output This module is with 3WX2 channel audio amplifier. If the horn is needed, access the speaker port. It is recommended to use 4 Ω / 3 w speakers.If the headset is inserted, the audio will automatically switch to the headphone channel, and the speaker channel will be closed automatically. 4>. Volume Turn the VOL encoder to adjust the volume, while the LCD screen displays the volume series. 5>. Frequency regulation Turn the FRE encoder to adjust the reception frequency, while the LCD screen displays the current frequency, and press the encoder handle to the mute/non-mute switch. 6>. Mute Press the VOL knob to switch the mute/non-mute button down. 7>. AMCAP switch Long press the FRE knob to switch on or off the AMCAP, the LCD display subtitle ON means to turn on the AMCAP, and OFF means to turn off the AMCAP. 8>. AMCAP threshold adjustment(when the AMCAP switch on) Short press the FRE knob to AMCAP threshold adjustment interface, you can adjust the movement threshold of the AMCAP according to the specific usage situation. The adjustment range is 0-20. The higher the value is, the higher the threshold is, the easier the weak signal is to be silent. Vice versa. 9>. Serial port (without serial port control) The module reserved TTL level serial port control interface. TTL serial port and this module communication need to connect the module's UART_RX, UART_TX and GND (the corresponding position of PCB is marked). You can use the external MCU or the computer serial port to send the command control module related functions. Note: because the computer serial port is not TTL level, connect the computer communication, it is necessary to connect the RS323 level to TTL power leveling device or the USB TTL level serial port module to communicate with this module. This operation requires professionals. 10>. User Settings This module can set the backlight state according to the user's specific usage. When the power is off, press the FRE button to turn on, and the B0 indicates that the backlight is always bright. B0 indicates that the backlight is closed for 20 seconds, and the setting is effective after the restart. Change the Settings state to repeat this step to switch. The backlight has no operation for 20 seconds. 11>. Stereo /mono switch terminal. Stereo/mono terminals are used to set the FM receiving mode of the module. This terminal is suspended for Stereo reception mode, and it is a single channel receiving mode.   6. FM with squelch receiver module AT instruction: Baud rate: 38400 TTL level   No. Name Example Instruction Range Return position 1 Set current frequency point AT+FRE=875 current frequency point is 87.5MHz  870-1080 MHz Current frequency point/ERR 2 Frequency point-0.1MHZ AT+FRED     Current frequency point Le 30-août-19 à 13:44:50 Paris, le vendeur a ajouté les informations suivantes:

1. Introduction   This FM stereo digital radio circuit board module has built-in DSP digital noise processing. When there is no signal, it will automatically mute and get rid of the noise of the traditional FM radio.   2.   Parameter   NO. Parameter Value 1 Output power 500mW (drive earphone), 3Wx2 (drive horn) 2 Frequency range 50Hz-18KHz  3 Receiving frequency range 87.0MHz-108.0MHz 4 Equivalent noise Greater than 30dB 5 Power supply voltage 3.0V-5.0V 6 Power supply current 1000mA at maximum volume, 60mA at minimum volume (for reference only) 7 Sound track Stereo       3. Using attention:   1>. The power supply voltage is strictly prohibited to exceed the power supply voltage range of this module. 2>. Do not touch the back part of the module when working, so as not to affect the normal work of this module or cause the short-circuit burn module.   4. Feature   1>. Advanced digital audio signal processing technology (DSP) and FM phase-locked loop modulation (PLL) make the sound quality more realistic, more stable performance, and long working frequency without deviation. 2>. LCD display is more intuitive and accurate, with extremely low power consumption and minimal noise interference. 3>. 30 digital volume adjustment, with buttons, easy to operate. 4>. Automatically storage data before power off. 5>. Automatic switch of speaker/headphone output. 6>. Quartz crystal steady frequency, temperature change reception frequency, no longer drift. 7>. It uses professional audio DSP to analyze and process the audio signal, and automatically mute when there is no signal or weak signal. 8>. It uses incremental digital rotary encoder to adjust the volume and frequency, using the feel is good, positioning accuracy, stable and durable, 360 ° rotating without blind Angle. 9> Support serial communication control, available computer or MCU and other devices with serial ports to control all functions of the module.   5. Instruction   1>. Power supply Module corresponding port (marked on PCB board). “-” and “+” are the anode and cathode of the power (battery). The power supply is recommended for battery or other stabilized power supply.You cannot use a power supply without filter (such as mobile phone charger, mobile power supply, and other switching power supply), otherwise the interference caused by power supply will affect the normal work of this module. The normal working voltage of this module is 3.0-5.0V, not exceeding this range. At the maximum volume of the module, the maximum power supply current is around 1A, which requires the battery to output enough current. 2>. Antenna The FM_ANT port is used to connect the FM antenna. To better receive the FM signal, it is recommended to extend the antenna with a length of 75cm. 3>. Headset/speaker output This module is with 3WX2 channel audio amplifier. If the horn is needed, access the speaker port. It is recommended to use 4 Ω / 3 w speakers.If the headset is inserted, the audio will automatically switch to the headphone channel, and the speaker channel will be closed automatically. 4>. Volume Turn the VOL encoder to adjust the volume, while the LCD screen displays the volume series. 5>. Frequency regulation Turn the FRE encoder to adjust the reception frequency, while the LCD screen displays the current frequency, and press the encoder handle to the mute/non-mute switch. 6>. Mute Press the VOL knob to switch the mute/non-mute button down. 7>. AMCAP switch Long press the FRE knob to switch on or off the AMCAP, the LCD display subtitle ON means to turn on the AMCAP, and OFF means to turn off the AMCAP. 8>. AMCAP threshold adjustment(when the AMCAP switch on) Short press the FRE knob to AMCAP threshold adjustment interface, you can adjust the movement threshold of the AMCAP according to the specific usage situation. The adjustment range is 0-20. The higher the value is, the higher the threshold is, the easier the weak signal is to be silent. Vice versa. 9>. Serial port (without serial port control) The module reserved TTL level serial port control interface. TTL serial port and this module communication need to connect the module's UART_RX, UART_TX and GND (the corresponding position of PCB is marked). You can use the external MCU or the computer serial port to send the command control module related functions. Note: because the computer serial port is not TTL level, connect the computer communication, it is necessary to connect the RS323 level to TTL power leveling device or the USB TTL level serial port module to communicate with this module. This operation requires professionals. 10>. User Settings This module can set the backlight state according to the user's specific usage. When the power is off, press the FRE button to turn on, and the B0 indicates that the backlight is always bright. B0 indicates that the backlight is closed for 20 seconds, and the setting is effective after the restart. Change the Settings state to repeat this step to switch. The backlight has no operation for 20 seconds. 11>. Stereo /mono switch terminal. Stereo/mono terminals are used to set the FM receiving mode of the module. This terminal is suspended for Stereo reception mode, and it is a single channel receiving mode.   6. FM with squelch receiver module AT instruction: Baud rate: 38400 TTL level   No. Name Example Instruction Range Return position 1 Set current frequency point AT+FRE=875 current frequency point is 87.5MHz  870-1080 MHz Current frequency point/ERR 2 Frequency point-0.1MHZ AT+FRED     Current frequency point   Le 30-août-19 à 11:05:14 Paris, le vendeur a ajouté les informations suivantes:

Store category Sign Up Now ! You may also like 4-Port 3.4A 77W USB HUB Phone Desktop Wall Charger Fast Charging Station Adapter Product Description 新增網頁1 4-Port 3.4A 77W USB HUB Phone Desktop Wall Charger Fast Charging Station Adapter BRAND NEW Item ! Never Used !! we will answer any of your questions regarding item(s)& service within 24 hrs. Features: Brand new and high quality. 4-Port 5V 3.4A USB HUB Wall Charger for Phone Fast Charging Station Adapter Overload protection and short circuit protection Long cable design allows long distance use Ideal for smart phones, tablet PCs, mp3, power bank Lightweight and compact, easy to carry, great for travel Description: 4-Port 5V 3.4A USB HUB Wall Charger for Phone Fast Charging Station Adapter Overload protection and short circuit protection Long cable design allows long distance use Ideal for smart phones, tablet PCs, mp3, power bank Lightweight and compact, easy to carry, great for travel Packing Include: 1 x 4-Port USB Wall Charger About the seller Shipping & handling Terms of sales Payment Contact us About the seller Welcome to shop in my store,we carry thousand of excellent items, w e always value client service as well as product quality.Please feel free to contact us for any concerns. We will leave positive feedback to buyer as soon as buyer pays for the item.We highly appreciate that you can contact with us before you leaving Negative feedback or Neutral feedback.We will offer help to resolve your problems as fast as possible. Shipping & handling Shipping & Handling: All the orders will be processed within stated time after payment is received. We ONLY ship your item to your PayPal shipping address. If you want your package to be sent to any address other than your Paypal shipping address, please state it clearly in the PayPal note section and also confirm with us by email.   Terms of sales All sales are final. Refunds given only if item found defective on arrive (DOA) and cannot be replaced. Replacement is available for wrong or defective item receipt within the first 30 days,it's free of extra charge. Please contact us for the return procedure. Payment PayPal - we accept Paypal as payment method only,you can use credit care to pay via Paypal. We ONLY ship your item to your PayPal shipping address. If you want your package to be sent to any address other than your Paypal shipping address, please state it clearly in the PayPal note section and also confirm with us by email. Payment is expected within 7 days after auction end. This is serious business, so please make sure you are serious before bidding the item. Contact us Please contact us if you have any questions,you will receive answer within 24 hours,we work 7 days a week.

Bonjour Nous mettons en vente cet ensemble de cartes composé d’une carte ALCATEL GD3 et CS2 ALCATEL-LUCENT GD-3 Gateway Driver Processing Unit 3EH73084A Carte flash 256MB   ALCATEL OMNIPCX CS-2 Call Serveur Processing Unité Module 3EH73086AB3 avec HDD 5K320-120 et carte SLANX4   En parfait état esthétique et fonctionnel.   Les photos illustrant l’annonce sont contractuelles, vous achetez ce qui y figure.   Pour l’expédition à l’international les frais d’envoi varient selon la destination. On a mis 50euros à titre indicatif. Merci pour votre compréhension. Hello We are selling this set of cards consisting of a card ALCATEL GD3 and CS2 ALCATEL-LUCENT GD-3 Gateway Driver Processing Unit 3EH73084AE with 256MB flash card ALCATEL OMNIPCX CS-2 Call Server Processing Unit Module 3EH73086AB3 with HDD 5K320-120 and SLANX4 Card In perfect aesthetic and functional state. The pictures illustrating the advertisement are contractual, you buy what is there. For international shipping the shipping costs vary depending on the destination. We put 50euros as an indication. Thanks for your understanding.

Ensemble coque silicone antichoc pour Google Pixel 4a (4G) + Protection d'écran en verre trempé autocollant.  Produits neufs, jamais utilisés.  Coque en silicone semi-rigide de haute qualité, offrant une protection intégrale au Pixel 4a  contre les chocs, rayures et accrocs  (l'objectif photo est protégé par un cerclage en relief pour éviter tout contact du module photo avec les surfaces planes).  Couleur noir carbone.  Ecran de protection en verre trempé inrayable, parfaitement adapté au Google Pixel 4a (avec découpe pour l'objetif avant).  Envoi rapide et soigné, livraison en 2 à 3 jours ouvrés en France. 

Yaesu FTV-901R, transverter 28MHz / 50MHz & 144MHz. État : Occasion Excellent cosmetic state. No scratches on paint.  Unfortunately no 70cm module. Other pictures on demand.

ICOM IC 718+ integrated DSP + Digimode cable + original hand mike. Bought in 2014 from ICOM-France, was not used for over 5 years and stored in original box.  Works perfectly full 100 W output. Not modified. Original Band limits of 2013. Provided with all accessories. Auxiliary DSP module installed. Digi mode cable to CAT port of the rig, Audio+USB to computer provided alongside. Original hand mike provided. Mint state. For international shipment, please write me. 73 de F4HCV

Transmetteur FM Bluetooth 4.2 Kit De Voiture Chargeur Allume Cigare Avec 2 Porte USB Grand Vitesse Sortie pour iPhone, Androit Smartphone, Tablette Tactile et Camera (BT-74) L'appareil est conçu pour être utilisé avec un lecteur MP3 Bluetooth, équipé d'un module Bluetooth professionnel haute performance et d'une puce de décodeur MP3. Envoyer le signal sans fil, sans rien modifier dans la voiture, aussi comme un lecteur de musique de divertissement et comme un kit de sécurité pour la voiture et accessible. Spécification Version Bluetooth: V4.2 + EDR Fréquence de Bluetooth: 2.4GHZ Sensibilité: 42db +/- 3db Tension: 12-24 V Courant de sauvegarde: 45mA Portée efficace: 2 M Fréquence FM: 87.5 MHZ-108 MHZ Port de charge: 5 V / 2.4A / 5V1A Puissance totale: 17W Dimension Taille du produit: 4.6 * 6.7 * 10.5 cm / 1.8 * 2.6 * 4.1in Poids du produit: 49 g / 1,8 oz Paquet 1 * Chargeur de voiture 1 * Manuel de l'utilisateur 1 * 3.5mm Câble NOTES 1. Assurez-vous d'insérer l'appareil après le démarrage du moteur de la voiture. 2. Lors du démarrage de la voiture, la pression affecte l'effet de charge et peut même endommager le chargeur. 3. N'utilisez pas plus de trois appareils en même temps si l'alimentation est trop importante car cela pourrait endommager l'équipement. 4. N'utilisez pas le chargeur de voiture quand le temps est orageux; Ne pas utiliser après le lavage de la voiture immédiatement, il est susceptible de provoquer une corrosion des composants. 5. Retirez l'appareil lorsque vous avez fini de l'utiliser. Fonction de support A2DP, le téléphone peut être automatiquement connecté à un appareil bluetooth dès que le produit est alimenté Prend en charge une carte TF externe et un disque USB pouvant lire des fichiers musicaux au format mp3 ou wma Kit mains libres avec Bluetooth, une fois l'appel mis en pause automatiquement la musique, via l'audio de la voiture pour effectuer des appels mains libres; rendre la conduite plus sûre Full-frequency 87.5-108.0MHZ, affichage numérique LED, montre la fréquence de l'état de fonctionnement Prend en charge l'entrée auxiliaire et la sortie, à travers le câble audio, connecter le trou AUX et la prise casque 3,5 mm du téléphone mobile, la fréquence de la machine et la fréquence FM, la musique mobile pour la lecture audio de l'automobile Track Page Views With Auctiva's FREE Counter