Broadcast fm radio

Broadcast FM Band Stop Filter (88 - 108 MHz FM Trap) WLFR Includes  1x RTL-SDR Blog Broadcast FM Band-Stop Filter 1x SMA male to SMA male adapter Blocks the broadcast FM band between 88 – 108 MHz with over 50dB of attenuation.  Designed for maximum attenuation between 88 - 108 MHz and the 3dB roll off points are at 76 MHz and 122 MHz. Insertion loss is less than 0.5 dB between 0 – 1 GHz, and mostly less than 1.5 dB between 1 – 3 GHz.  Uses SMA female connectors. Comes with a free SMA male to SMA male adapter. A broadcast FM block filter can help if you have very strong broadcasts in your area that are overloading the SDR dongle. Also known as “FM Trap”. Notes: RX filter only. Designed for SDR users, but might also be useful for TV users struggling with FM interference. But TV users please carefully check the spectrum analyzer graphs and 3dB roll off points to ensure that it will not block a TV signal of interest. e.g. Channels between 76 - 88 MHz could be attenuated enough to lose reception. Le 16-juil.-19 à 17:26:15 Paris, le vendeur a ajouté les informations suivantes:

BROADCAST FM 88 108MHZ MARQUE QUARK REFERENCE FALCON 50 PUISSANCE 30W AUDIO MONO XLR ENTREE MPX BNC ENTREE SCA BNC UTILISATION UNIQUEMENT EN ATELIER POUR ESSAI TRAITEMENT DE SONO VENDU COMME SUR LE PHOTO

Includes  1x RTL-SDR Blog Broadcast FM Band-Stop Filter 1x SMA male to SMA male adapter Blocks the broadcast FM band between 88 – 108 MHz with over 50dB of attenuation.  Designed for maximum attenuation between 88 - 108 MHz and the 3dB roll off points are at 76 MHz and 122 MHz. Insertion loss is less than 0.5 dB between 0 – 1 GHz, and mostly less than 1.5 dB between 1 – 3 GHz.  Uses SMA female connectors. Comes with a free SMA male to SMA male adapter. A broadcast FM block filter can help if you have very strong broadcasts in your area that are overloading the SDR dongle. Also known as “FM Trap”. Notes: RX filter only. Designed for SDR users, but might also be useful for TV users struggling with FM interference. But TV users please carefully check the spectrum analyzer graphs and 3dB roll off points to ensure that it will not block a TV signal of interest. e.g. Channels between 76 - 88 MHz could be attenuated enough to lose reception.   Includes  1x RTL-SDR Blog Broadcast FM Band-Stop Filter 1x SMA male to SMA male adapter Blocks the broadcast FM band between 88 – 108 MHz with over 50dB of attenuation.  Designed for maximum attenuation between 88 - 108 MHz and the 3dB roll off points are at 76 MHz and 122 MHz. Insertion loss is less than 0.5 dB between 0 – 1 GHz, and mostly less than 1.5 dB between 1 – 3 GHz.  Uses SMA female connectors. Comes with a free SMA male to SMA male adapter. A broadcast FM block filter can help if you have very strong broadcasts in your area that are overloading the SDR dongle. Also known as “FM Trap”. Notes: RX filter only. Designed for SDR users, but might also be useful for TV users struggling with FM interference. But TV users please carefully check the spectrum analyzer graphs and 3dB roll off points to ensure that it will not block a TV signal of interest. e.g. Channels between 76 - 88 MHz could be attenuated enough to lose reception. Le 26-août-19 à 20:34:53 Paris, le vendeur a ajouté les informations suivantes:

Includes  1x RTL-SDR Blog Broadcast FM Band-Stop Filter 1x SMA male to SMA male adapter Blocks the broadcast FM band between 88 – 108 MHz with over 50dB of attenuation.  Designed for maximum attenuation between 88 - 108 MHz and the 3dB roll off points are at 76 MHz and 122 MHz. Insertion loss is less than 0.5 dB between 0 – 1 GHz, and mostly less than 1.5 dB between 1 – 3 GHz.  Uses SMA female connectors. Comes with a free SMA male to SMA male adapter. A broadcast FM block filter can help if you have very strong broadcasts in your area that are overloading the SDR dongle. Also known as “FM Trap”. Notes: RX filter only. Designed for SDR users, but might also be useful for TV users struggling with FM interference. But TV users please carefully check the spectrum analyzer graphs and 3dB roll off points to ensure that it will not block a TV signal of interest. e.g. Channels between 76 - 88 MHz could be attenuated enough to lose reception.   Le 22-mai-19 à 08:54:20 Paris, le vendeur a ajouté les informations suivantes:

Includes  1x RTL-SDR Blog Broadcast FM Band-Stop Filter 1x SMA male to SMA male adapter Blocks the broadcast FM band between 88 – 108 MHz with over 50dB of attenuation.  Designed for maximum attenuation between 88 - 108 MHz and the 3dB roll off points are at 76 MHz and 122 MHz. Insertion loss is less than 0.5 dB between 0 – 1 GHz, and mostly less than 1.5 dB between 1 – 3 GHz.  Uses SMA female connectors. Comes with a free SMA male to SMA male adapter. A broadcast FM block filter can help if you have very strong broadcasts in your area that are overloading the SDR dongle. Also known as “FM Trap”. Notes: RX filter only. Designed for SDR users, but might also be useful for TV users struggling with FM interference. But TV users please carefully check the spectrum analyzer graphs and 3dB roll off points to ensure that it will not block a TV signal of interest. e.g. Channels between 76 - 88 MHz could be attenuated enough to lose reception. Le 04-juil.-19 à 14:50:06 Paris, le vendeur a ajouté les informations suivantes:

Includes  1x RTL-SDR Blog Broadcast FM Band-Stop Filter 1x SMA male to SMA male adapter Blocks the broadcast FM band between 88 – 108 MHz with over 50dB of attenuation.  Designed for maximum attenuation between 88 - 108 MHz and the 3dB roll off points are at 76 MHz and 122 MHz. Insertion loss is less than 0.5 dB between 0 – 1 GHz, and mostly less than 1.5 dB between 1 – 3 GHz.  Uses SMA female connectors. Comes with a free SMA male to SMA male adapter. A broadcast FM block filter can help if you have very strong broadcasts in your area that are overloading the SDR dongle. Also known as “FM Trap”. Notes: RX filter only. Designed for SDR users, but might also be useful for TV users struggling with FM interference. But TV users please carefully check the spectrum analyzer graphs and 3dB roll off points to ensure that it will not block a TV signal of interest. e.g. Channels between 76 - 88 MHz could be attenuated enough to lose reception. Le 13-juil.-19 à 11:10:30 Paris, le vendeur a ajouté les informations suivantes:

Includes  1x RTL-SDR Blog Broadcast FM Band-Stop Filter 1x SMA male to SMA male adapter Blocks the broadcast FM band between 88 – 108 MHz with over 50dB of attenuation.  Designed for maximum attenuation between 88 - 108 MHz and the 3dB roll off points are at 76 MHz and 122 MHz. Insertion loss is less than 0.5 dB between 0 – 1 GHz, and mostly less than 1.5 dB between 1 – 3 GHz.  Uses SMA female connectors. Comes with a free SMA male to SMA male adapter. A broadcast FM block filter can help if you have very strong broadcasts in your area that are overloading the SDR dongle. Also known as “FM Trap”. Notes: RX filter only. Designed for SDR users, but might also be useful for TV users struggling with FM interference. But TV users please carefully check the spectrum analyzer graphs and 3dB roll off points to ensure that it will not block a TV signal of interest. e.g. Channels between 76 - 88 MHz could be attenuated enough to lose reception. Le 17-sept.-19 à 16:27:16 Paris, le vendeur a ajouté les informations suivantes:

1. Introduction   This FM stereo digital radio circuit board module has built-in DSP digital noise processing. When there is no signal, it will automatically mute and get rid of the noise of the traditional FM radio.   2.   Parameter   NO. Parameter Value 1 Output power 500mW (drive earphone), 3Wx2 (drive horn) 2 Frequency range 50Hz-18KHz  3 Receiving frequency range 87.0MHz-108.0MHz 4 Equivalent noise Greater than 30dB 5 Power supply voltage 3.0V-5.0V 6 Power supply current 1000mA at maximum volume, 60mA at minimum volume (for reference only) 7 Sound track Stereo       3. Using attention:   1>. The power supply voltage is strictly prohibited to exceed the power supply voltage range of this module. 2>. Do not touch the back part of the module when working, so as not to affect the normal work of this module or cause the short-circuit burn module.   4. Feature   1>. Advanced digital audio signal processing technology (DSP) and FM phase-locked loop modulation (PLL) make the sound quality more realistic, more stable performance, and long working frequency without deviation. 2>. LCD display is more intuitive and accurate, with extremely low power consumption and minimal noise interference. 3>. 30 digital volume adjustment, with buttons, easy to operate. 4>. Automatically storage data before power off. 5>. Automatic switch of speaker/headphone output. 6>. Quartz crystal steady frequency, temperature change reception frequency, no longer drift. 7>. It uses professional audio DSP to analyze and process the audio signal, and automatically mute when there is no signal or weak signal. 8>. It uses incremental digital rotary encoder to adjust the volume and frequency, using the feel is good, positioning accuracy, stable and durable, 360 ° rotating without blind Angle. 9> Support serial communication control, available computer or MCU and other devices with serial ports to control all functions of the module.   5. Instruction   1>. Power supply Module corresponding port (marked on PCB board). “-” and “+” are the anode and cathode of the power (battery). The power supply is recommended for battery or other stabilized power supply.You cannot use a power supply without filter (such as mobile phone charger, mobile power supply, and other switching power supply), otherwise the interference caused by power supply will affect the normal work of this module. The normal working voltage of this module is 3.0-5.0V, not exceeding this range. At the maximum volume of the module, the maximum power supply current is around 1A, which requires the battery to output enough current. 2>. Antenna The FM_ANT port is used to connect the FM antenna. To better receive the FM signal, it is recommended to extend the antenna with a length of 75cm. 3>. Headset/speaker output This module is with 3WX2 channel audio amplifier. If the horn is needed, access the speaker port. It is recommended to use 4 Ω / 3 w speakers.If the headset is inserted, the audio will automatically switch to the headphone channel, and the speaker channel will be closed automatically. 4>. Volume Turn the VOL encoder to adjust the volume, while the LCD screen displays the volume series. 5>. Frequency regulation Turn the FRE encoder to adjust the reception frequency, while the LCD screen displays the current frequency, and press the encoder handle to the mute/non-mute switch. 6>. Mute Press the VOL knob to switch the mute/non-mute button down. 7>. AMCAP switch Long press the FRE knob to switch on or off the AMCAP, the LCD display subtitle ON means to turn on the AMCAP, and OFF means to turn off the AMCAP. 8>. AMCAP threshold adjustment(when the AMCAP switch on) Short press the FRE knob to AMCAP threshold adjustment interface, you can adjust the movement threshold of the AMCAP according to the specific usage situation. The adjustment range is 0-20. The higher the value is, the higher the threshold is, the easier the weak signal is to be silent. Vice versa. 9>. Serial port (without serial port control) The module reserved TTL level serial port control interface. TTL serial port and this module communication need to connect the module's UART_RX, UART_TX and GND (the corresponding position of PCB is marked). You can use the external MCU or the computer serial port to send the command control module related functions. Note: because the computer serial port is not TTL level, connect the computer communication, it is necessary to connect the RS323 level to TTL power leveling device or the USB TTL level serial port module to communicate with this module. This operation requires professionals. 10>. User Settings This module can set the backlight state according to the user's specific usage. When the power is off, press the FRE button to turn on, and the B0 indicates that the backlight is always bright. B0 indicates that the backlight is closed for 20 seconds, and the setting is effective after the restart. Change the Settings state to repeat this step to switch. The backlight has no operation for 20 seconds. 11>. Stereo /mono switch terminal. Stereo/mono terminals are used to set the FM receiving mode of the module. This terminal is suspended for Stereo reception mode, and it is a single channel receiving mode.   6. FM with squelch receiver module AT instruction: Baud rate: 38400 TTL level   No. Name Example Instruction Range Return position 1 Set current frequency point AT+FRE=875 current frequency point is 87.5MHz  870-1080 MHz Current frequency point/ERR 2 Frequency point-0.1MHZ AT+FRED     Current frequency point   Le 10-juil.-19 à 05:53:17 Paris, le vendeur a ajouté les informations suivantes:

1. Introduction   This FM stereo digital radio circuit board module has built-in DSP digital noise processing. When there is no signal, it will automatically mute and get rid of the noise of the traditional FM radio.   2.   Parameter   NO. Parameter Value 1 Output power 500mW (drive earphone), 3Wx2 (drive horn) 2 Frequency range 50Hz-18KHz  3 Receiving frequency range 87.0MHz-108.0MHz 4 Equivalent noise Greater than 30dB 5 Power supply voltage 3.0V-5.0V 6 Power supply current 1000mA at maximum volume, 60mA at minimum volume (for reference only) 7 Sound track Stereo       3. Using attention:   1>. The power supply voltage is strictly prohibited to exceed the power supply voltage range of this module. 2>. Do not touch the back part of the module when working, so as not to affect the normal work of this module or cause the short-circuit burn module.   4. Feature   1>. Advanced digital audio signal processing technology (DSP) and FM phase-locked loop modulation (PLL) make the sound quality more realistic, more stable performance, and long working frequency without deviation. 2>. LCD display is more intuitive and accurate, with extremely low power consumption and minimal noise interference. 3>. 30 digital volume adjustment, with buttons, easy to operate. 4>. Automatically storage data before power off. 5>. Automatic switch of speaker/headphone output. 6>. Quartz crystal steady frequency, temperature change reception frequency, no longer drift. 7>. It uses professional audio DSP to analyze and process the audio signal, and automatically mute when there is no signal or weak signal. 8>. It uses incremental digital rotary encoder to adjust the volume and frequency, using the feel is good, positioning accuracy, stable and durable, 360 ° rotating without blind Angle. 9> Support serial communication control, available computer or MCU and other devices with serial ports to control all functions of the module.   5. Instruction   1>. Power supply Module corresponding port (marked on PCB board). “-” and “+” are the anode and cathode of the power (battery). The power supply is recommended for battery or other stabilized power supply.You cannot use a power supply without filter (such as mobile phone charger, mobile power supply, and other switching power supply), otherwise the interference caused by power supply will affect the normal work of this module. The normal working voltage of this module is 3.0-5.0V, not exceeding this range. At the maximum volume of the module, the maximum power supply current is around 1A, which requires the battery to output enough current. 2>. Antenna The FM_ANT port is used to connect the FM antenna. To better receive the FM signal, it is recommended to extend the antenna with a length of 75cm. 3>. Headset/speaker output This module is with 3WX2 channel audio amplifier. If the horn is needed, access the speaker port. It is recommended to use 4 Ω / 3 w speakers.If the headset is inserted, the audio will automatically switch to the headphone channel, and the speaker channel will be closed automatically. 4>. Volume Turn the VOL encoder to adjust the volume, while the LCD screen displays the volume series. 5>. Frequency regulation Turn the FRE encoder to adjust the reception frequency, while the LCD screen displays the current frequency, and press the encoder handle to the mute/non-mute switch. 6>. Mute Press the VOL knob to switch the mute/non-mute button down. 7>. AMCAP switch Long press the FRE knob to switch on or off the AMCAP, the LCD display subtitle ON means to turn on the AMCAP, and OFF means to turn off the AMCAP. 8>. AMCAP threshold adjustment(when the AMCAP switch on) Short press the FRE knob to AMCAP threshold adjustment interface, you can adjust the movement threshold of the AMCAP according to the specific usage situation. The adjustment range is 0-20. The higher the value is, the higher the threshold is, the easier the weak signal is to be silent. Vice versa. 9>. Serial port (without serial port control) The module reserved TTL level serial port control interface. TTL serial port and this module communication need to connect the module's UART_RX, UART_TX and GND (the corresponding position of PCB is marked). You can use the external MCU or the computer serial port to send the command control module related functions. Note: because the computer serial port is not TTL level, connect the computer communication, it is necessary to connect the RS323 level to TTL power leveling device or the USB TTL level serial port module to communicate with this module. This operation requires professionals. 10>. User Settings This module can set the backlight state according to the user's specific usage. When the power is off, press the FRE button to turn on, and the B0 indicates that the backlight is always bright. B0 indicates that the backlight is closed for 20 seconds, and the setting is effective after the restart. Change the Settings state to repeat this step to switch. The backlight has no operation for 20 seconds. 11>. Stereo /mono switch terminal. Stereo/mono terminals are used to set the FM receiving mode of the module. This terminal is suspended for Stereo reception mode, and it is a single channel receiving mode.   6. FM with squelch receiver module AT instruction: Baud rate: 38400 TTL level   No. Name Example Instruction Range Return position 1 Set current frequency point AT+FRE=875 current frequency point is 87.5MHz  870-1080 MHz Current frequency point/ERR 2 Frequency point-0.1MHZ AT+FRED     Current frequency point   Le 09-juil.-19 à 17:37:11 Paris, le vendeur a ajouté les informations suivantes:

1. Introduction   This FM stereo digital radio circuit board module has built-in DSP digital noise processing. When there is no signal, it will automatically mute and get rid of the noise of the traditional FM radio.   2.   Parameter   NO. Parameter Value 1 Output power 500mW (drive earphone), 3Wx2 (drive horn) 2 Frequency range 50Hz-18KHz  3 Receiving frequency range 87.0MHz-108.0MHz 4 Equivalent noise Greater than 30dB 5 Power supply voltage 3.0V-5.0V 6 Power supply current 1000mA at maximum volume, 60mA at minimum volume (for reference only) 7 Sound track Stereo       3. Using attention:   1>. The power supply voltage is strictly prohibited to exceed the power supply voltage range of this module. 2>. Do not touch the back part of the module when working, so as not to affect the normal work of this module or cause the short-circuit burn module.   4. Feature   1>. Advanced digital audio signal processing technology (DSP) and FM phase-locked loop modulation (PLL) make the sound quality more realistic, more stable performance, and long working frequency without deviation. 2>. LCD display is more intuitive and accurate, with extremely low power consumption and minimal noise interference. 3>. 30 digital volume adjustment, with buttons, easy to operate. 4>. Automatically storage data before power off. 5>. Automatic switch of speaker/headphone output. 6>. Quartz crystal steady frequency, temperature change reception frequency, no longer drift. 7>. It uses professional audio DSP to analyze and process the audio signal, and automatically mute when there is no signal or weak signal. 8>. It uses incremental digital rotary encoder to adjust the volume and frequency, using the feel is good, positioning accuracy, stable and durable, 360 ° rotating without blind Angle. 9> Support serial communication control, available computer or MCU and other devices with serial ports to control all functions of the module.   5. Instruction   1>. Power supply Module corresponding port (marked on PCB board). “-” and “+” are the anode and cathode of the power (battery). The power supply is recommended for battery or other stabilized power supply.You cannot use a power supply without filter (such as mobile phone charger, mobile power supply, and other switching power supply), otherwise the interference caused by power supply will affect the normal work of this module. The normal working voltage of this module is 3.0-5.0V, not exceeding this range. At the maximum volume of the module, the maximum power supply current is around 1A, which requires the battery to output enough current. 2>. Antenna The FM_ANT port is used to connect the FM antenna. To better receive the FM signal, it is recommended to extend the antenna with a length of 75cm. 3>. Headset/speaker output This module is with 3WX2 channel audio amplifier. If the horn is needed, access the speaker port. It is recommended to use 4 Ω / 3 w speakers.If the headset is inserted, the audio will automatically switch to the headphone channel, and the speaker channel will be closed automatically. 4>. Volume Turn the VOL encoder to adjust the volume, while the LCD screen displays the volume series. 5>. Frequency regulation Turn the FRE encoder to adjust the reception frequency, while the LCD screen displays the current frequency, and press the encoder handle to the mute/non-mute switch. 6>. Mute Press the VOL knob to switch the mute/non-mute button down. 7>. AMCAP switch Long press the FRE knob to switch on or off the AMCAP, the LCD display subtitle ON means to turn on the AMCAP, and OFF means to turn off the AMCAP. 8>. AMCAP threshold adjustment(when the AMCAP switch on) Short press the FRE knob to AMCAP threshold adjustment interface, you can adjust the movement threshold of the AMCAP according to the specific usage situation. The adjustment range is 0-20. The higher the value is, the higher the threshold is, the easier the weak signal is to be silent. Vice versa. 9>. Serial port (without serial port control) The module reserved TTL level serial port control interface. TTL serial port and this module communication need to connect the module's UART_RX, UART_TX and GND (the corresponding position of PCB is marked). You can use the external MCU or the computer serial port to send the command control module related functions. Note: because the computer serial port is not TTL level, connect the computer communication, it is necessary to connect the RS323 level to TTL power leveling device or the USB TTL level serial port module to communicate with this module. This operation requires professionals. 10>. User Settings This module can set the backlight state according to the user's specific usage. When the power is off, press the FRE button to turn on, and the B0 indicates that the backlight is always bright. B0 indicates that the backlight is closed for 20 seconds, and the setting is effective after the restart. Change the Settings state to repeat this step to switch. The backlight has no operation for 20 seconds. 11>. Stereo /mono switch terminal. Stereo/mono terminals are used to set the FM receiving mode of the module. This terminal is suspended for Stereo reception mode, and it is a single channel receiving mode.   6. FM with squelch receiver module AT instruction: Baud rate: 38400 TTL level   No. Name Example Instruction Range Return position 1 Set current frequency point AT+FRE=875 current frequency point is 87.5MHz  870-1080 MHz Current frequency point/ERR 2 Frequency point-0.1MHZ AT+FRED     Current frequency point   Le 08-juil.-19 à 15:14:31 Paris, le vendeur a ajouté les informations suivantes:

1. Introduction   This FM stereo digital radio circuit board module has built-in DSP digital noise processing. When there is no signal, it will automatically mute and get rid of the noise of the traditional FM radio.   2.   Parameter   NO. Parameter Value 1 Output power 500mW (drive earphone), 3Wx2 (drive horn) 2 Frequency range 50Hz-18KHz  3 Receiving frequency range 87.0MHz-108.0MHz 4 Equivalent noise Greater than 30dB 5 Power supply voltage 3.0V-5.0V 6 Power supply current 1000mA at maximum volume, 60mA at minimum volume (for reference only) 7 Sound track Stereo       3. Using attention:   1>. The power supply voltage is strictly prohibited to exceed the power supply voltage range of this module. 2>. Do not touch the back part of the module when working, so as not to affect the normal work of this module or cause the short-circuit burn module.   4. Feature   1>. Advanced digital audio signal processing technology (DSP) and FM phase-locked loop modulation (PLL) make the sound quality more realistic, more stable performance, and long working frequency without deviation. 2>. LCD display is more intuitive and accurate, with extremely low power consumption and minimal noise interference. 3>. 30 digital volume adjustment, with buttons, easy to operate. 4>. Automatically storage data before power off. 5>. Automatic switch of speaker/headphone output. 6>. Quartz crystal steady frequency, temperature change reception frequency, no longer drift. 7>. It uses professional audio DSP to analyze and process the audio signal, and automatically mute when there is no signal or weak signal. 8>. It uses incremental digital rotary encoder to adjust the volume and frequency, using the feel is good, positioning accuracy, stable and durable, 360 ° rotating without blind Angle. 9> Support serial communication control, available computer or MCU and other devices with serial ports to control all functions of the module.   5. Instruction   1>. Power supply Module corresponding port (marked on PCB board). “-” and “+” are the anode and cathode of the power (battery). The power supply is recommended for battery or other stabilized power supply.You cannot use a power supply without filter (such as mobile phone charger, mobile power supply, and other switching power supply), otherwise the interference caused by power supply will affect the normal work of this module. The normal working voltage of this module is 3.0-5.0V, not exceeding this range. At the maximum volume of the module, the maximum power supply current is around 1A, which requires the battery to output enough current. 2>. Antenna The FM_ANT port is used to connect the FM antenna. To better receive the FM signal, it is recommended to extend the antenna with a length of 75cm. 3>. Headset/speaker output This module is with 3WX2 channel audio amplifier. If the horn is needed, access the speaker port. It is recommended to use 4 Ω / 3 w speakers.If the headset is inserted, the audio will automatically switch to the headphone channel, and the speaker channel will be closed automatically. 4>. Volume Turn the VOL encoder to adjust the volume, while the LCD screen displays the volume series. 5>. Frequency regulation Turn the FRE encoder to adjust the reception frequency, while the LCD screen displays the current frequency, and press the encoder handle to the mute/non-mute switch. 6>. Mute Press the VOL knob to switch the mute/non-mute button down. 7>. AMCAP switch Long press the FRE knob to switch on or off the AMCAP, the LCD display subtitle ON means to turn on the AMCAP, and OFF means to turn off the AMCAP. 8>. AMCAP threshold adjustment(when the AMCAP switch on) Short press the FRE knob to AMCAP threshold adjustment interface, you can adjust the movement threshold of the AMCAP according to the specific usage situation. The adjustment range is 0-20. The higher the value is, the higher the threshold is, the easier the weak signal is to be silent. Vice versa. 9>. Serial port (without serial port control) The module reserved TTL level serial port control interface. TTL serial port and this module communication need to connect the module's UART_RX, UART_TX and GND (the corresponding position of PCB is marked). You can use the external MCU or the computer serial port to send the command control module related functions. Note: because the computer serial port is not TTL level, connect the computer communication, it is necessary to connect the RS323 level to TTL power leveling device or the USB TTL level serial port module to communicate with this module. This operation requires professionals. 10>. User Settings This module can set the backlight state according to the user's specific usage. When the power is off, press the FRE button to turn on, and the B0 indicates that the backlight is always bright. B0 indicates that the backlight is closed for 20 seconds, and the setting is effective after the restart. Change the Settings state to repeat this step to switch. The backlight has no operation for 20 seconds. 11>. Stereo /mono switch terminal. Stereo/mono terminals are used to set the FM receiving mode of the module. This terminal is suspended for Stereo reception mode, and it is a single channel receiving mode.   6. FM with squelch receiver module AT instruction: Baud rate: 38400 TTL level   No. Name Example Instruction Range Return position 1 Set current frequency point AT+FRE=875 current frequency point is 87.5MHz  870-1080 MHz Current frequency point/ERR 2 Frequency point-0.1MHZ AT+FRED     Current frequency point   Le 10-août-19 à 10:14:47 Paris, le vendeur a ajouté les informations suivantes:

1. Introduction   This FM stereo digital radio circuit board module has built-in DSP digital noise processing. When there is no signal, it will automatically mute and get rid of the noise of the traditional FM radio.   2.   Parameter   NO. Parameter Value 1 Output power 500mW (drive earphone), 3Wx2 (drive horn) 2 Frequency range 50Hz-18KHz  3 Receiving frequency range 87.0MHz-108.0MHz 4 Equivalent noise Greater than 30dB 5 Power supply voltage 3.0V-5.0V 6 Power supply current 1000mA at maximum volume, 60mA at minimum volume (for reference only) 7 Sound track Stereo       3. Using attention:   1>. The power supply voltage is strictly prohibited to exceed the power supply voltage range of this module. 2>. Do not touch the back part of the module when working, so as not to affect the normal work of this module or cause the short-circuit burn module.   4. Feature   1>. Advanced digital audio signal processing technology (DSP) and FM phase-locked loop modulation (PLL) make the sound quality more realistic, more stable performance, and long working frequency without deviation. 2>. LCD display is more intuitive and accurate, with extremely low power consumption and minimal noise interference. 3>. 30 digital volume adjustment, with buttons, easy to operate. 4>. Automatically storage data before power off. 5>. Automatic switch of speaker/headphone output. 6>. Quartz crystal steady frequency, temperature change reception frequency, no longer drift. 7>. It uses professional audio DSP to analyze and process the audio signal, and automatically mute when there is no signal or weak signal. 8>. It uses incremental digital rotary encoder to adjust the volume and frequency, using the feel is good, positioning accuracy, stable and durable, 360 ° rotating without blind Angle. 9> Support serial communication control, available computer or MCU and other devices with serial ports to control all functions of the module.   5. Instruction   1>. Power supply Module corresponding port (marked on PCB board). “-” and “+” are the anode and cathode of the power (battery). The power supply is recommended for battery or other stabilized power supply.You cannot use a power supply without filter (such as mobile phone charger, mobile power supply, and other switching power supply), otherwise the interference caused by power supply will affect the normal work of this module. The normal working voltage of this module is 3.0-5.0V, not exceeding this range. At the maximum volume of the module, the maximum power supply current is around 1A, which requires the battery to output enough current. 2>. Antenna The FM_ANT port is used to connect the FM antenna. To better receive the FM signal, it is recommended to extend the antenna with a length of 75cm. 3>. Headset/speaker output This module is with 3WX2 channel audio amplifier. If the horn is needed, access the speaker port. It is recommended to use 4 Ω / 3 w speakers.If the headset is inserted, the audio will automatically switch to the headphone channel, and the speaker channel will be closed automatically. 4>. Volume Turn the VOL encoder to adjust the volume, while the LCD screen displays the volume series. 5>. Frequency regulation Turn the FRE encoder to adjust the reception frequency, while the LCD screen displays the current frequency, and press the encoder handle to the mute/non-mute switch. 6>. Mute Press the VOL knob to switch the mute/non-mute button down. 7>. AMCAP switch Long press the FRE knob to switch on or off the AMCAP, the LCD display subtitle ON means to turn on the AMCAP, and OFF means to turn off the AMCAP. 8>. AMCAP threshold adjustment(when the AMCAP switch on) Short press the FRE knob to AMCAP threshold adjustment interface, you can adjust the movement threshold of the AMCAP according to the specific usage situation. The adjustment range is 0-20. The higher the value is, the higher the threshold is, the easier the weak signal is to be silent. Vice versa. 9>. Serial port (without serial port control) The module reserved TTL level serial port control interface. TTL serial port and this module communication need to connect the module's UART_RX, UART_TX and GND (the corresponding position of PCB is marked). You can use the external MCU or the computer serial port to send the command control module related functions. Note: because the computer serial port is not TTL level, connect the computer communication, it is necessary to connect the RS323 level to TTL power leveling device or the USB TTL level serial port module to communicate with this module. This operation requires professionals. 10>. User Settings This module can set the backlight state according to the user's specific usage. When the power is off, press the FRE button to turn on, and the B0 indicates that the backlight is always bright. B0 indicates that the backlight is closed for 20 seconds, and the setting is effective after the restart. Change the Settings state to repeat this step to switch. The backlight has no operation for 20 seconds. 11>. Stereo /mono switch terminal. Stereo/mono terminals are used to set the FM receiving mode of the module. This terminal is suspended for Stereo reception mode, and it is a single channel receiving mode.   6. FM with squelch receiver module AT instruction: Baud rate: 38400 TTL level   No. Name Example Instruction Range Return position 1 Set current frequency point AT+FRE=875 current frequency point is 87.5MHz  870-1080 MHz Current frequency point/ERR 2 Frequency point-0.1MHZ AT+FRED     Current frequency point Le 30-août-19 à 13:44:50 Paris, le vendeur a ajouté les informations suivantes:

1. Introduction   This FM stereo digital radio circuit board module has built-in DSP digital noise processing. When there is no signal, it will automatically mute and get rid of the noise of the traditional FM radio.   2.   Parameter   NO. Parameter Value 1 Output power 500mW (drive earphone), 3Wx2 (drive horn) 2 Frequency range 50Hz-18KHz  3 Receiving frequency range 87.0MHz-108.0MHz 4 Equivalent noise Greater than 30dB 5 Power supply voltage 3.0V-5.0V 6 Power supply current 1000mA at maximum volume, 60mA at minimum volume (for reference only) 7 Sound track Stereo       3. Using attention:   1>. The power supply voltage is strictly prohibited to exceed the power supply voltage range of this module. 2>. Do not touch the back part of the module when working, so as not to affect the normal work of this module or cause the short-circuit burn module.   4. Feature   1>. Advanced digital audio signal processing technology (DSP) and FM phase-locked loop modulation (PLL) make the sound quality more realistic, more stable performance, and long working frequency without deviation. 2>. LCD display is more intuitive and accurate, with extremely low power consumption and minimal noise interference. 3>. 30 digital volume adjustment, with buttons, easy to operate. 4>. Automatically storage data before power off. 5>. Automatic switch of speaker/headphone output. 6>. Quartz crystal steady frequency, temperature change reception frequency, no longer drift. 7>. It uses professional audio DSP to analyze and process the audio signal, and automatically mute when there is no signal or weak signal. 8>. It uses incremental digital rotary encoder to adjust the volume and frequency, using the feel is good, positioning accuracy, stable and durable, 360 ° rotating without blind Angle. 9> Support serial communication control, available computer or MCU and other devices with serial ports to control all functions of the module.   5. Instruction   1>. Power supply Module corresponding port (marked on PCB board). “-” and “+” are the anode and cathode of the power (battery). The power supply is recommended for battery or other stabilized power supply.You cannot use a power supply without filter (such as mobile phone charger, mobile power supply, and other switching power supply), otherwise the interference caused by power supply will affect the normal work of this module. The normal working voltage of this module is 3.0-5.0V, not exceeding this range. At the maximum volume of the module, the maximum power supply current is around 1A, which requires the battery to output enough current. 2>. Antenna The FM_ANT port is used to connect the FM antenna. To better receive the FM signal, it is recommended to extend the antenna with a length of 75cm. 3>. Headset/speaker output This module is with 3WX2 channel audio amplifier. If the horn is needed, access the speaker port. It is recommended to use 4 Ω / 3 w speakers.If the headset is inserted, the audio will automatically switch to the headphone channel, and the speaker channel will be closed automatically. 4>. Volume Turn the VOL encoder to adjust the volume, while the LCD screen displays the volume series. 5>. Frequency regulation Turn the FRE encoder to adjust the reception frequency, while the LCD screen displays the current frequency, and press the encoder handle to the mute/non-mute switch. 6>. Mute Press the VOL knob to switch the mute/non-mute button down. 7>. AMCAP switch Long press the FRE knob to switch on or off the AMCAP, the LCD display subtitle ON means to turn on the AMCAP, and OFF means to turn off the AMCAP. 8>. AMCAP threshold adjustment(when the AMCAP switch on) Short press the FRE knob to AMCAP threshold adjustment interface, you can adjust the movement threshold of the AMCAP according to the specific usage situation. The adjustment range is 0-20. The higher the value is, the higher the threshold is, the easier the weak signal is to be silent. Vice versa. 9>. Serial port (without serial port control) The module reserved TTL level serial port control interface. TTL serial port and this module communication need to connect the module's UART_RX, UART_TX and GND (the corresponding position of PCB is marked). You can use the external MCU or the computer serial port to send the command control module related functions. Note: because the computer serial port is not TTL level, connect the computer communication, it is necessary to connect the RS323 level to TTL power leveling device or the USB TTL level serial port module to communicate with this module. This operation requires professionals. 10>. User Settings This module can set the backlight state according to the user's specific usage. When the power is off, press the FRE button to turn on, and the B0 indicates that the backlight is always bright. B0 indicates that the backlight is closed for 20 seconds, and the setting is effective after the restart. Change the Settings state to repeat this step to switch. The backlight has no operation for 20 seconds. 11>. Stereo /mono switch terminal. Stereo/mono terminals are used to set the FM receiving mode of the module. This terminal is suspended for Stereo reception mode, and it is a single channel receiving mode.   6. FM with squelch receiver module AT instruction: Baud rate: 38400 TTL level   No. Name Example Instruction Range Return position 1 Set current frequency point AT+FRE=875 current frequency point is 87.5MHz  870-1080 MHz Current frequency point/ERR 2 Frequency point-0.1MHZ AT+FRED     Current frequency point   Le 30-août-19 à 11:05:14 Paris, le vendeur a ajouté les informations suivantes:

Broadcast radio FM A vendre émetteur FM de 40 watts de marque ELENOS. Réglable de 2 à 40 Watts. Entrée composite pour codeur RDS et/ou Stéréo. Top qualité c'est du Pro made in iltaly. En parfait état de fonctionnement, révisé et dispo de suite. Documentation complète.

LIKE NEW !   A COMPLETE FM Broadcast STATION 88-108Mhz : with FM 30 watts Pilot exciter, with RDS encoder, with Stereo coder, with FM 4 bands audio processor, with 2x Broadband antennas + 2 ways splitter: - BW DSPX = 880 €uros - AZTEC AUDEMAT FMB10 = 170 €uros - RVR PTX30UHT = 340 €uros - 2x Antennas = 290 €uros - Splitter 2 ways = 140 €uros Total initial price = 1820 euros ******************************************************************************************************************************** ALL NEW Never used !  - STEREO CODER and FM audio processor: BW - DSPX (it's not the '' mini '' version) But the great DSPX broadcast processor for FM - Dj's - Mastering...   (I pay this apparatus: 1800 €uros with all taxes) ALL new, never used, with technical notice, software and pdf (free) on the BW compagny site:  for the notice: http://a-bc.co.uk/Misc/Tools/DSPX-FM%20v320%20Manual.pdf Processeur audio FM traitement de son numérique multibandes 4 bandes ==>   https://www.youtube.com/watch?v=oLPv2J8_X1o     or     https://www.youtube.com/watch?v=5IFjZmZlzWo - 4 bandes AGC - limiteur 4 bandes - Clippeur 3 bandes - Connectivité LAN - Stereo Coder (50us or 75 us) - Output MPX 19Khz - Input RDS (with sync pilot) - sortie droite-gauche avec clippeur indépendant - Ethernet RJ45... Like NEW - Just revised and calibrated for 330 €uros by ''AUDEMAT-Bordeaux(France)'' - RDS Encoder: Aztec FMB10/40  Configuration wizard Simulated PS and Radiotext display Dynamic PS data from automation Labeling Command interpreter 19 kHz Synchronization - External, Internal or Automatic Synchronization monitoring Software control of RDS injection level – no trimpots Software adjustment of 57 kHz Phase ASCII Commands to enable or disable the RDS SCA Composite bypass feature in case of failure Superb spectral purity of the RDS signal Like NEW - Because used only 6 months in ''help mode'' - FM 88-108 MHz PLL Exciter transmitter - 0 to 30 watts: RVR - PTX30UHT Like NEW - 2x Broadband antennas for 1kW maxi (Mat Equipment) + 1,2 Kw Splitter 2 ways N/N ------------------------------------------------------------------------------------------------------------------------------ ------------------------------------------------------------------------------------------------------------------------------ NO DISPUTE - MY EVALUATION FEEDBACK IS MY GUARANTEE France: Paiement par virement uniquement, transport en plusieurs colis. International seller: NO PAYPAL (for no big service taxes) ==>  ONLY: money transfer bank to bank  with IBAN/BIC contact me for the right transport charges, with your country. It's heavy !  transport in 3 solids cardboards.