Implementation of

Hello, I am selling my Gimball, only used a couple of times for sport videos recording. Will come in the original box and the invoice. Details below: ACR The Plus is a device capable of stabilising small digital cameras and DSLRs. The stabilisers job is to make sure that the horison level is perfectly kept where it should be even during the most insane shot – it also negates unwanted round movements of the camera. An agile operator experienced in working with Steadicam or similar systems can achieve results not possible before. The versatility of this technology is limited solely by the creativity of users and the gear itself is very easy to configure. Handing over The Plus during a single, continuous shot, changing the shooting action from handheld to UAV, working in normal and inverted modes – these tasks require only a moment of preparation and open completely new horizones to open-minded filmmakers. Give it a try! The stabiliser Thanks to using a twin gyro & accelerometer system the stabilisation itself is sharp and precise while keeping the device simple to use. A powerful processor allowed us to enhance the primal functionality of the stabiliser with a set of new functions: more natural, iconic Follow Mode, larger number of saveable settings profiles, more reliable operation in demanding conditions. Three direct drive brushless motors were created to perfectly control the camera on each of the stabilised axes. The stabiliser was built according to our own solutions and technology. We used the best available materials – aircraft grade duraluminum, carbon fibres. The electronics and motors were developed from scratch to meet the requirements of our most demanding users.   The device Is powered by a single LiIon battery (included in the set) fitted inside a dedicated compartment within the carbon tube. Depending on your gear configuration it can work constantly up to two hours on a single charge. The battery charger is also included. A uniqe feature is the possibility to power up external accessories attached close to your camera straight from the main battery thanks to an auxillary power socket located at the camera shelf. Such accessories include wireless video transmission systems, follow focus systems, etc. ACR The Plus is the upgraded version of the classic BeSteady ONE – the gimble which started our journey. The first units of the predcessor were delivered to the first users around the end of 2013. We would not have made it without the support of hundreds of wonderful people who supported us via the initial KickStarter campaign. Thanks to the invaluable help from many enthusiasts we were able to revaluate, test and complete the upgrade project with success.    The heart of the BeSteady is within the mainboard. Highly modified BaseCam software, developed in direct cooperation with Alexei Moskalenko, enabled us to create a product tailored for your needs. A fast Cortex processor, vast internal memory and twin gyro & accelerometer system allows the device to easily cope with tasks such as fast running, shooting from moving vehicles and working at uncommon and extreme angles and positions. The lack of complicated configuration procedures (the so-called PID tuning) is gone with the introduction of simple, understandable sliders responsible for setting the needed parameters for every axis. The uniqe, very characteristic handheld mode, the Follow Mode, allows the operator to catch smooth scenes during continuous takes thanks to responsive and natural movement control system with a lot of precise math behind it. Moreover, the device can be controled using a dedicated analog Thumbstick or an external remote control device. The stabiliser can work in different modes thanks to the implementation of advanced control & stabilisation algorythms. The basic mode of operation is the Xtended Stabilisation – where the device maintains the exact camera position targ

DATAVIDEO VP-332 DV Repeater One Input to 5 Output 6 port IEEE1394 Distribution Amplifier Occasion Features • DV Hub with 6 x 6 Pin DV (IEEE1394) Ports • Allows Multiple Devices To Be Connected To One Port • Allows One DV Device To Feed Up To Five Outputs • Boosts DV Signal For Extended Cable Runs (200m Max) • Up to 400 Mbps Data Rate • Fully Interoperable with FireWire™ and iLink™ Implementation of IEEE1394 Standard • Supports Self-Powered or Cable-Powered mode • Supports Hot Plug and Play Functions • Supports asynchronous and isochronous data transfers • Supports PC Windows 98/SE/ME/XP/2000 system and Mac OS 8.6 or above Installation 1. Plug the DC power adapter into the power jack of the DV Repeater 2. Connect the IEEE1394 host port to any of the DV Repeater ports 3. Install the IEEE1394 device driver from Windows 98/SE or above 4. Connect your IEEE1394 devices to the DV Repeater Note: If a single port drops out, the LED indicator of that port will be off Specifications • Bi-directional IEEE1394 distribution amplifier • Provides six IEEE1394 ports at 100/200/400 Mbps • Compliant with IEEE1394, 1394a standard • Supports up to 63 devices cascaded • Over-current detection and protection of each port • Bus-powered LED indicators • External Power Supply 12VDC, 12 Watts (included) • Size: WxDxH 10x5x2 cm (approx) Attention je ne fournie pas l’adaptateur secteur, seulement le boitier VP 332 DV Repeater

NEW OLD STOCK. RARE. Device that recognises tempo from audio signal and turns it into MIDI signal.  For example you can synchronise two turntables with a synth or a drum machine.  VOYAGER 1 analyzes audio signals from vinyl, CD or tape and calculates the BPM of two tracks simultaneously. Both BPMs are displayed but, more importantly, the beat information from one channel is used to generate a MIDI Clock signal, which runs in synchronization with the audio track. In original box and comes with manual.   FEATURES: • Performance: BPM Range = 60 - 230 BPM Audio/MIDI synchronisation delay = less than 3mS • Lock-in time = 2 to 4 sec's (from introduction of readable beat information). • Displays: 2 x 7 Segments, 3 character (LED). 1 x MIDI Clock rotating display (8 x LED's). Beat Tracking indicator (3 x LED's). • Controls: Channel 1 select, Channel 2 select, Run/Pause, Cue, Beat. One Re-Set, Tap (Stop) Tempo edit, Sync Pull/Push adjust. • MIDI Implementation: System Real Time/Clock commands = Transmitted. • Connectors: Channel 1 Input/Output, Channel 2 Input/Output, MIDI Clock Out, AC adaptor. • Power Supply: 9vDC, 250mA (RED PSU) included. • Dimensions/Weight 180(W) x 132(D) x 50(H) mm, 1.65 Kg. • Intelligent Software: Constantly analyses and calculates the BPM of two audio inputs (vinyl or CD/tape). • Channel 1 & 2 Displays: The BPM readings from the audio inputs are shown clearly on 3 digit LED displays. • Run/Pause Button: Controls the running status of the external MIDI sequencer. • Cue Button: Pre-sets the VOYAGER 1 to the BPM of your next audio track prior to performance. • The MIDI sequencer and audio track can then be started simultaneously from a predetermined cue point in the audio track. • Beat One Reset Button: Re-aligns the start point (beat1/bar1) of the current pattern in the MIDI sequencer with any chosen point in the audio track. • MIDI Clock Display: 8 LED display rotates' at the detected BPM rate when the VOYAGER 1 is in RUN mode. • Beat Tracking Indicator: 3 LED display shows any beat synchronisation adjustments made by the VOYAGER 1. • Tap (Stop) Button: Used to manually enter a BPM and/or STOP the MIDI Clock.

Sold without power supply. Functional. The IS-SPX-1300 Inspired Signage XPress Player (FG1231-11) offers a simple way to deliver digital signage solutions.  The rich set of functionalities offered by the IS-SPX-1300 simplifies the implementation, management and maintenance of a range of audio/visual communication solutions. The IS-SPX-1300 is designed to satisfy the reliability needs of nonstop 24/7 service and minimize maintenance costs.  The IS-SPX-1300 contains no moving parts and is engineered to be used wherever digital signage displays are utilized.  Whether integrated behind displays, beneath a technical floor, or in a custom enclosure, the IS-SPX-1300 is ready to deliver with a small form factor and a low power draw. The USB interface can be used to extend the internal storage through memory sticks or externally powered hard drives. The same interface can support external devices such as touch screen controllers or keyboards.