Inside third

  Description: MINIWHIP VLF LF HF ACTIVE ANTENNA.This is known PA0NHC newest design of MiniWhip Antenna. I have redesigned and built it on SMD components but the circuit diagram itself stayed the same as it had been described on his web page in open source. This sale includes the MiniWhip and Power Splitter assembled and tested boards. They go with its circuit diagrams and part list specification. No cables or connectors are included. This new version of PA0NHC MiniWhip Antenna has these features.New version, using modern BF998 and BCX54 semi conductors.Real class A circuitry, clean reception without IMD.One coax connection.Broadband R/C coupling to the receiver, no transformer For best signal-to-noise ratio:install the Miniwhip onto a well grounded mast.connect "GND" of the Miniwhip PCB to that mast.place HI-Ui ferrite cores (Ui bwtween 5000 and 10.000) on the beginning and end of all cables to block cable noise currents. Specifications: Frequency range: 10 KHz - 30 MHz Power: 12 - 15 volts at 150 mA Second order output intercept point: Greater than + 70 dBm Third order output intercept point: Greater than + 30 dBm Maximum output power: in excess of - 15 dBm PCB Size: Length (mm): As the picture show Connector: BNC Feed line: 50 - 100 ohm coaxial cable up to 100 meter long T o note please: Each antenna performs as good as its installation permits it to. Any active antenna is not working good inside the house! It should be mounted OUTSIDE and as high as possible. Place this MiniWhip antenna PCB inside suitable enclosure of your choise and mount outside the house. Probably for the enclosure you can use a piece of the PVC tube which available in varios diameters in a local store. Do not use metal enclosure! It wont work there! For max. sensitivity: this antenna should be positioned as high and free from meta Package include: 1Set Board Note:   The color might be a little different from the actual product due to color display of different monitors.  Please allow 1-3 cm error.     Le 16-oct.-19 à 20:29:37 Paris, le vendeur a ajouté les informations suivantes:

Description: MINIWHIP VLF LF HF ACTIVE ANTENNA.This is known PA0NHC newest design of MiniWhip Antenna. I have redesigned and built it on SMD components but the circuit diagram itself stayed the same as it had been described on his web page in open source. This sale includes the MiniWhip and Power Splitter assembled and tested boards. They go with its circuit diagrams and part list specification. No cables or connectors are included. This new version of PA0NHC MiniWhip Antenna has these features.New version, using modern BF998 and BCX54 semi conductors.Real class A circuitry, clean reception without IMD.One coax connection.Broadband R/C coupling to the receiver, no transformer For best signal-to-noise ratio:install the Miniwhip onto a well grounded mast.connect "GND" of the Miniwhip PCB to that mast.place HI-Ui ferrite cores (Ui bwtween 5000 and 10.000) on the beginning and end of all cables to block cable noise currents. Specifications: Frequency range: 10 KHz - 30 MHz Power: 12 - 15 volts at 150 mA Second order output intercept point: Greater than + 70 dBm Third order output intercept point: Greater than + 30 dBm Maximum output power: in excess of - 15 dBm PCB Size: Length (mm): As the picture show Connector: BNC Feed line: 50 - 100 ohm coaxial cable up to 100 meter long T o note please: Each antenna performs as good as its installation permits it to. Any active antenna is not working good inside the house! It should be mounted OUTSIDE and as high as possible. Place this MiniWhip antenna PCB inside suitable enclosure of your choise and mount outside the house. Probably for the enclosure you can use a piece of the PVC tube which available in varios diameters in a local store. Do not use metal enclosure! It wont work there! For max. sensitivity: this antenna should be positioned as high and free from meta Package include: 1Set Board Note:   The color might be a little different from the actual product due to color display of different monitors.  Please allow 1-3 cm error. Le 02-nov.-19 à 04:55:03 Paris, le vendeur a ajouté les informations suivantes:

Description: MINIWHIP VLF LF HF ACTIVE ANTENNA.This is known PA0NHC newest design of MiniWhip Antenna. I have redesigned and built it on SMD components but the circuit diagram itself stayed the same as it had been described on his web page in open source. This sale includes the MiniWhip and Power Splitter assembled and tested boards. They go with its circuit diagrams and part list specification. No cables or connectors are included. This new version of PA0NHC MiniWhip Antenna has these features.New version, using modern BF998 and BCX54 semi conductors.Real class A circuitry, clean reception without IMD.One coax connection.Broadband R/C coupling to the receiver, no transformer For best signal-to-noise ratio:install the Miniwhip onto a well grounded mast.connect "GND" of the Miniwhip PCB to that mast.place HI-Ui ferrite cores (Ui bwtween 5000 and 10.000) on the beginning and end of all cables to block cable noise currents. Specifications: Frequency range: 10 KHz - 30 MHz Power: 12 - 15 volts at 150 mA Second order output intercept point: Greater than + 70 dBm Third order output intercept point: Greater than + 30 dBm Maximum output power: in excess of - 15 dBm PCB Size: Length (mm): As the picture show Connector: BNC Feed line: 50 - 100 ohm coaxial cable up to 100 meter long T o note please: Each antenna performs as good as its installation permits it to. Any active antenna is not working good inside the house! It should be mounted OUTSIDE and as high as possible. Place this MiniWhip antenna PCB inside suitable enclosure of your choise and mount outside the house. Probably for the enclosure you can use a piece of the PVC tube which available in varios diameters in a local store. Do not use metal enclosure! It wont work there! For max. sensitivity: this antenna should be positioned as high and free from meta Package include: 1Set Board Note:   The color might be a little different from the actual product due to color display of different monitors.  Please allow 1-3 cm error. Le 31-oct.-19 à 08:24:31 Paris, le vendeur a ajouté les informations suivantes:

Description: MINIWHIP VLF LF HF ACTIVE ANTENNA.This is known PA0NHC newest design of MiniWhip Antenna. I have redesigned and built it on SMD components but the circuit diagram itself stayed the same as it had been described on his web page in open source. This sale includes the MiniWhip and Power Splitter assembled and tested boards. They go with its circuit diagrams and part list specification. No cables or connectors are included. This new version of PA0NHC MiniWhip Antenna has these features.New version, using modern BF998 and BCX54 semi conductors.Real class A circuitry, clean reception without IMD.One coax connection.Broadband R/C coupling to the receiver, no transformer For best signal-to-noise ratio:install the Miniwhip onto a well grounded mast.connect "GND" of the Miniwhip PCB to that mast.place HI-Ui ferrite cores (Ui bwtween 5000 and 10.000) on the beginning and end of all cables to block cable noise currents. Specifications: Frequency range: 10 KHz - 30 MHz Power: 12 - 15 volts at 150 mA Second order output intercept point: Greater than + 70 dBm Third order output intercept point: Greater than + 30 dBm Maximum output power: in excess of - 15 dBm PCB Size: Length (mm): As the picture show Connector: BNC Feed line: 50 - 100 ohm coaxial cable up to 100 meter long T o note please: Each antenna performs as good as its installation permits it to. Any active antenna is not working good inside the house! It should be mounted OUTSIDE and as high as possible. Place this MiniWhip antenna PCB inside suitable enclosure of your choise and mount outside the house. Probably for the enclosure you can use a piece of the PVC tube which available in varios diameters in a local store. Do not use metal enclosure! It wont work there! For max. sensitivity: this antenna should be positioned as high and free from meta Package include: 1Set Board Note:   The color might be a little different from the actual product due to color display of different monitors.  Please allow 1-3 cm error. Le 18-nov.-19 à 18:30:46 Paris, le vendeur a ajouté les informations suivantes:

Description: MINIWHIP VLF LF HF ACTIVE ANTENNA.This is known PA0NHC newest design of MiniWhip Antenna. I have redesigned and built it on SMD components but the circuit diagram itself stayed the same as it had been described on his web page in open source. This sale includes the MiniWhip and Power Splitter assembled and tested boards. They go with its circuit diagrams and part list specification. No cables or connectors are included. This new version of PA0NHC MiniWhip Antenna has these features.New version, using modern BF998 and BCX54 semi conductors.Real class A circuitry, clean reception without IMD.One coax connection.Broadband R/C coupling to the receiver, no transformer For best signal-to-noise ratio:install the Miniwhip onto a well grounded mast.connect "GND" of the Miniwhip PCB to that mast.place HI-Ui ferrite cores (Ui bwtween 5000 and 10.000) on the beginning and end of all cables to block cable noise currents. Specifications: Frequency range: 10 KHz - 30 MHz Power: 12 - 15 volts at 150 mA Second order output intercept point: Greater than + 70 dBm Third order output intercept point: Greater than + 30 dBm Maximum output power: in excess of - 15 dBm PCB Size: Length (mm): As the picture show Connector: BNC Feed line: 50 - 100 ohm coaxial cable up to 100 meter long T o note please: Each antenna performs as good as its installation permits it to. Any active antenna is not working good inside the house! It should be mounted OUTSIDE and as high as possible. Place this MiniWhip antenna PCB inside suitable enclosure of your choise and mount outside the house. Probably for the enclosure you can use a piece of the PVC tube which available in varios diameters in a local store. Do not use metal enclosure! It wont work there! For max. sensitivity: this antenna should be positioned as high and free from meta Package include: 1Set Board Note:   The color might be a little different from the actual product due to color display of different monitors.  Please allow 1-3 cm error. Le 17-nov.-19 à 11:15:12 Paris, le vendeur a ajouté les informations suivantes:

Miniwhip Active Antenna HF LF VlF Mini Whip Shortwave SDR RX Portable Recei M ZH Description: MINIWHIP VLF LF HF ACTIVE ANTENNA.This is known PA0NHC newest design of MiniWhip Antenna. I have redesigned and built it on SMD components but the circuit diagram itself stayed the same as it had been described on his web page in open source. This sale includes the MiniWhip and Power Splitter assembled and tested boards. They go with its circuit diagrams and part list specification. No cables or connectors are included. This new version of PA0NHC MiniWhip Antenna has these features.New version, using modern BF998 and BCX54 semi conductors.Real class A circuitry, clean reception without IMD.One coax connection.Broadband R/C coupling to the receiver, no transformer For best signal-to-noise ratio:install the Miniwhip onto a well grounded mast.connect "GND" of the Miniwhip PCB to that mast.place HI-Ui ferrite cores (Ui bwtween 5000 and 10.000) on the beginning and end of all cables to block cable noise currents. Specifications: Frequency range: 10 KHz - 30 MHz Power: 12 - 15 volts at 150 mA Second order output intercept point: Greater than + 70 dBm Third order output intercept point: Greater than + 30 dBm Maximum output power: in excess of - 15 dBm PCB Size: Length (mm): As the picture show Connector: BNC Feed line: 50 - 100 ohm coaxial cable up to 100 meter long T o note please: Each antenna performs as good as its installation permits it to. Any active antenna is not working good inside the house! It should be mounted OUTSIDE and as high as possible. Place this MiniWhip antenna PCB inside suitable enclosure of your choise and mount outside the house. Probably for the enclosure you can use a piece of the PVC tube which available in varios diameters in a local store. Do not use metal enclosure! It wont work there! For max. sensitivity: this antenna should be positioned as high and free from meta Package include: 1Set Board Note:   The color might be a little different from the actual product due to color display of different monitors.  Please allow 1-3 cm error. Le 16-nov.-19 à 10:16:12 Paris, le vendeur a ajouté les informations suivantes:

Miniwhip Active Antenna MC LF VlF Mini Whip Shortwave SDR RX Portable Recei M ZH Description: MINIWHIP VLF LF HF ACTIVE ANTENNA.This is known PA0NHC newest design of MiniWhip Antenna. I have redesigned and built it on SMD components but the circuit diagram itself stayed the same as it had been described on his web page in open source. This sale includes the MiniWhip and Power Splitter assembled and tested boards. They go with its circuit diagrams and part list specification. No cables or connectors are included. This new version of PA0NHC MiniWhip Antenna has these features.New version, using modern BF998 and BCX54 semi conductors.Real class A circuitry, clean reception without IMD.One coax connection.Broadband R/C coupling to the receiver, no transformer For best signal-to-noise ratio:install the Miniwhip onto a well grounded mast.connect "GND" of the Miniwhip PCB to that mast.place HI-Ui ferrite cores (Ui bwtween 5000 and 10.000) on the beginning and end of all cables to block cable noise currents. Specifications: Frequency range: 10 KHz - 30 MHz Power: 12 - 15 volts at 150 mA Second order output intercept point: Greater than + 70 dBm Third order output intercept point: Greater than + 30 dBm Maximum output power: in excess of - 15 dBm PCB Size: Length (mm): As the picture show Connector: BNC Feed line: 50 - 100 ohm coaxial cable up to 100 meter long T o note please: Each antenna performs as good as its installation permits it to. Any active antenna is not working good inside the house! It should be mounted OUTSIDE and as high as possible. Place this MiniWhip antenna PCB inside suitable enclosure of your choise and mount outside the house. Probably for the enclosure you can use a piece of the PVC tube which available in varios diameters in a local store. Do not use metal enclosure! It wont work there! For max. sensitivity: this antenna should be positioned as high and free from meta Package include: 1Set Board Note:   The color might be a little different from the actual product due to color display of different monitors.  Please allow 1-3 cm error. Le 16-nov.-19 à 10:23:15 Paris, le vendeur a ajouté les informations suivantes:

Description: MINIWHIP VLF LF HF ACTIVE ANTENNA.This is known PA0NHC newest design of MiniWhip Antenna. I have redesigned and built it on SMD components but the circuit diagram itself stayed the same as it had been described on his web page in open source. This sale includes the MiniWhip and Power Splitter assembled and tested boards. They go with its circuit diagrams and part list specification. No cables or connectors are included. This new version of PA0NHC MiniWhip Antenna has these features.New version, using modern BF998 and BCX54 semi conductors.Real class A circuitry, clean reception without IMD.One coax connection.Broadband R/C coupling to the receiver, no transformer For best signal-to-noise ratio:install the Miniwhip onto a well grounded mast.connect "GND" of the Miniwhip PCB to that mast.place HI-Ui ferrite cores (Ui bwtween 5000 and 10.000) on the beginning and end of all cables to block cable noise currents. Specifications: Frequency range: 10 KHz - 30 MHz Power: 12 - 15 volts at 150 mA Second order output intercept point: Greater than + 70 dBm Third order output intercept point: Greater than + 30 dBm Maximum output power: in excess of - 15 dBm PCB Size: Length (mm): As the picture show Connector: BNC Feed line: 50 - 100 ohm coaxial cable up to 100 meter long T o note please: Each antenna performs as good as its installation permits it to. Any active antenna is not working good inside the house! It should be mounted OUTSIDE and as high as possible. Place this MiniWhip antenna PCB inside suitable enclosure of your choise and mount outside the house. Probably for the enclosure you can use a piece of the PVC tube which available in varios diameters in a local store. Do not use metal enclosure! It wont work there! For max. sensitivity: this antenna should be positioned as high and free from meta Package include: 1Set Board Note:   The color might be a little different from the actual product due to color display of different monitors.  Please allow 1-3 cm error. Le 21-nov.-19 à 15:16:08 Paris, le vendeur a ajouté les informations suivantes:

Description: MINIWHIP VLF LF HF ACTIVE ANTENNA.This is known PA0NHC newest design of MiniWhip Antenna. I have redesigned and built it on SMD components but the circuit diagram itself stayed the same as it had been described on his web page in open source. This sale includes the MiniWhip and Power Splitter assembled and tested boards. They go with its circuit diagrams and part list specification. No cables or connectors are included. This new version of PA0NHC MiniWhip Antenna has these features.New version, using modern BF998 and BCX54 semi conductors.Real class A circuitry, clean reception without IMD.One coax connection.Broadband R/C coupling to the receiver, no transformer For best signal-to-noise ratio:install the Miniwhip onto a well grounded mast.connect "GND" of the Miniwhip PCB to that mast.place HI-Ui ferrite cores (Ui bwtween 5000 and 10.000) on the beginning and end of all cables to block cable noise currents. Specifications: Frequency range: 10 KHz - 30 MHz Power: 12 - 15 volts at 150 mA Second order output intercept point: Greater than + 70 dBm Third order output intercept point: Greater than + 30 dBm Maximum output power: in excess of - 15 dBm PCB Size: Length (mm): As the picture show Connector: BNC Feed line: 50 - 100 ohm coaxial cable up to 100 meter long T o note please: Each antenna performs as good as its installation permits it to. Any active antenna is not working good inside the house! It should be mounted OUTSIDE and as high as possible. Place this MiniWhip antenna PCB inside suitable enclosure of your choise and mount outside the house. Probably for the enclosure you can use a piece of the PVC tube which available in varios diameters in a local store. Do not use metal enclosure! It wont work there! For max. sensitivity: this antenna should be positioned as high and free from meta Package include: 1Set Board Note:   The color might be a little different from the actual product due to color display of different monitors.  Please allow 1-3 cm error. Le 19-déc.-19 à 03:27:15 Paris, le vendeur a ajouté les informations suivantes:

Miniwhip Active Antenna MC LF VlF Mini Whip Shortwave SDR RX Portable Recei M ZH Description: MINIWHIP VLF LF HF ACTIVE ANTENNA.This is known PA0NHC newest design of MiniWhip Antenna. I have redesigned and built it on SMD components but the circuit diagram itself stayed the same as it had been described on his web page in open source. This sale includes the MiniWhip and Power Splitter assembled and tested boards. They go with its circuit diagrams and part list specification. No cables or connectors are included. This new version of PA0NHC MiniWhip Antenna has these features.New version, using modern BF998 and BCX54 semi conductors.Real class A circuitry, clean reception without IMD.One coax connection.Broadband R/C coupling to the receiver, no transformer For best signal-to-noise ratio:install the Miniwhip onto a well grounded mast.connect "GND" of the Miniwhip PCB to that mast.place HI-Ui ferrite cores (Ui bwtween 5000 and 10.000) on the beginning and end of all cables to block cable noise currents. Specifications: Frequency range: 10 KHz - 30 MHz Power: 12 - 15 volts at 150 mA Second order output intercept point: Greater than + 70 dBm Third order output intercept point: Greater than + 30 dBm Maximum output power: in excess of - 15 dBm PCB Size: Length (mm): As the picture show Connector: BNC Feed line: 50 - 100 ohm coaxial cable up to 100 meter long T o note please: Each antenna performs as good as its installation permits it to. Any active antenna is not working good inside the house! It should be mounted OUTSIDE and as high as possible. Place this MiniWhip antenna PCB inside suitable enclosure of your choise and mount outside the house. Probably for the enclosure you can use a piece of the PVC tube which available in varios diameters in a local store. Do not use metal enclosure! It wont work there! For max. sensitivity: this antenna should be positioned as high and free from meta Package include: 1Set Board Note:   The color might be a little different from the actual product due to color display of different monitors.  Please allow 1-3 cm error. Le 06-févr.-20 à 21:45:18 Paris, le vendeur a ajouté les informations suivantes:

Description: MINIWHIP VLF LF HF ACTIVE ANTENNA.This is known PA0NHC newest design of MiniWhip Antenna. I have redesigned and built it on SMD components but the circuit diagram itself stayed the same as it had been described on his web page in open source. This sale includes the MiniWhip and Power Splitter assembled and tested boards. They go with its circuit diagrams and part list specification. No cables or connectors are included. This new version of PA0NHC MiniWhip Antenna has these features.New version, using modern BF998 and BCX54 semi conductors.Real class A circuitry, clean reception without IMD.One coax connection.Broadband R/C coupling to the receiver, no transformer For best signal-to-noise ratio:install the Miniwhip onto a well grounded mast.connect "GND" of the Miniwhip PCB to that mast.place HI-Ui ferrite cores (Ui bwtween 5000 and 10.000) on the beginning and end of all cables to block cable noise currents. Specifications: Frequency range: 10 KHz - 30 MHz Power: 12 - 15 volts at 150 mA Second order output intercept point: Greater than + 70 dBm Third order output intercept point: Greater than + 30 dBm Maximum output power: in excess of - 15 dBm PCB Size: Length (mm): As the picture show Connector: BNC Feed line: 50 - 100 ohm coaxial cable up to 100 meter long T o note please: Each antenna performs as good as its installation permits it to. Any active antenna is not working good inside the house! It should be mounted OUTSIDE and as high as possible. Place this MiniWhip antenna PCB inside suitable enclosure of your choise and mount outside the house. Probably for the enclosure you can use a piece of the PVC tube which available in varios diameters in a local store. Do not use metal enclosure! It wont work there! For max. sensitivity: this antenna should be positioned as high and free from meta Package include: 1Set Board Note:   The color might be a little different from the actual product due to color display of different monitors.  Please allow 1-3 cm error. Le 11-mars-20 à 13:30:27 Paris, le vendeur a ajouté les informations suivantes:

Description: MINIWHIP VLF LF HF ACTIVE ANTENNA.This is known PA0NHC newest design of MiniWhip Antenna. I have redesigned and built it on SMD components but the circuit diagram itself stayed the same as it had been described on his web page in open source. This sale includes the MiniWhip and Power Splitter assembled and tested boards. They go with its circuit diagrams and part list specification. No cables or connectors are included. This new version of PA0NHC MiniWhip Antenna has these features.New version, using modern BF998 and BCX54 semi conductors.Real class A circuitry, clean reception without IMD.One coax connection.Broadband R/C coupling to the receiver, no transformer For best signal-to-noise ratio:install the Miniwhip onto a well grounded mast.connect "GND" of the Miniwhip PCB to that mast.place HI-Ui ferrite cores (Ui bwtween 5000 and 10.000) on the beginning and end of all cables to block cable noise currents. Specifications: Frequency range: 10 KHz - 30 MHz Power: 12 - 15 volts at 150 mA Second order output intercept point: Greater than + 70 dBm Third order output intercept point: Greater than + 30 dBm Maximum output power: in excess of - 15 dBm PCB Size: Length (mm): As the picture show Connector: BNC Feed line: 50 - 100 ohm coaxial cable up to 100 meter long T o note please: Each antenna performs as good as its installation permits it to. Any active antenna is not working good inside the house! It should be mounted OUTSIDE and as high as possible. Place this MiniWhip antenna PCB inside suitable enclosure of your choise and mount outside the house. Probably for the enclosure you can use a piece of the PVC tube which available in varios diameters in a local store. Do not use metal enclosure! It wont work there! For max. sensitivity: this antenna should be positioned as high and free from meta Package include: 1Set Board Note:   The color might be a little different from the actual product due to color display of different monitors.  Please allow 1-3 cm error. Le 04-avr.-20 à 15:50:26 Paris, le vendeur a ajouté les informations suivantes:

Brand New Galaxy Z Fold2 5G 256GB - Mystic Black Specs Verizon Ready for use on Verizon ONLY Included Phone Headphones Charging Cable & Adapter Original Box NOT Included N/A DISPLAY Benchmarks Size: 7.6 inches Resolution: 2208 x 1768 pixels, 372 PPI Technology: Dynamic AMOLED Screen-to-body - Shows what approximate part of the frontal area of a phone its screen occupies. The value is calculated automatically based on the screen measured diagonally as a full rectangle without accounting for the rounded corners and the notch/cutout. " style="box-sizing: border-box; display: inline-block; cursor: pointer;">Screen-to-body: 89.00 % Features: Folding inside the device, 120Hz refresh rate, HDR support, Ambient light sensor, Proximity sensor Front cover display: 6.2 inches, 2260 x 816 pixels, AMOLED, Scratch-resistant glass (Corning Gorilla Glass) HARDWARE Benchmarks System chip - The System-on-a-Chip includes many of the device’s hardware modules like the processor, GPU, Wi-Fi, Bluetooth, and wireless radio. This field shows what particular system chip is used in the phone. " style="box-sizing: border-box; display: inline-block; cursor: pointer;">System chip: Qualcomm Snapdragon 865+ SM8250-AB Processor - This is the main computing component of a phone and is a major factor when it comes to the overall speed of the device. " style="box-sizing: border-box; display: inline-block; cursor: pointer;">Processor: Octa-core, 3100 MHz, Kryo 585, 64-bit, 7 nm GPU - The graphics processor is important for the smooth operation of the system and especially in games and other applications that may involve complex graphics and animations. " style="box-sizing: border-box; display: inline-block; cursor: pointer;">GPU: Adreno 650 RAM - This is the type of memory that the device uses to temporarily store data from the OS or currently-running apps. The more RAM available to the device, the better the performance will be when multiple or heavier programs are running. " style="box-sizing: border-box; display: inline-block; cursor: pointer;">RAM: 12GB LPDDR5 Internal storage: 256GB (UFS 3.1), available to use: 220.5 GB, not expandable Device type: Smartphone OS: Android (11, 10), Samsung One UI BATTERY Benchmarks Capacity - The bigger, the better! However, battery capacity is not the only factor that has an effect on battery life. Those include the chipset in use, the software running on the device, as well as the consumer's unique usage pattern. " style="box-sizing: border-box; display: inline-block; cursor: pointer;">Capacity: 4500 mAh Type: Not user replaceable Battery life test results: link Charging: Qualcomm Quick Charge 2.0, Samsung Adaptive Fast Charging, Qi and Powermat wireless charging, Reverse wireless charging Max charge speed: Wired: 25.0W; Wireless: 11.0W CAMERA Benchmarks Rear: Triple camera   Camera samples Main camera: 12 MP (OIS, PDAF) Specifications: Aperture size - The aperture of a camera is the opening through which light travels before it reaches the camera sensor. The smaller the number is, the bigger this opening is, allowing for more light to pass. " style="box-sizing: border-box; display: inline-block; cursor: pointer;">Aperture size:   F1.8;   Focal length - The lower (shorter) the focal length number, the wider the shot will be. Conversely, longer focal length cameras produce narrower frames, which can be used for telephoto (zoomed-in) purposes. " style="box-sizing: border-box; display: inline-block; cursor: pointer;">Focal length:   26 mm;   Sensor size - A bigger camera sensor is able to capture more light, and thus produce better photos. " style="box-sizing: border-box; display: inline-block; cursor: pointer;">Sensor size:   1/1.76";   Pixel size - The size of an individual pixel on a camera's sensor. The bigger, the better. " style="box-sizing: border-box; display: inline-block; cursor: pointer;">Pixel size:   1.8 μm Second camera: 12 MP (Telephoto, OIS, PDAF) Specifications: Optical zoom: 2.0x; Aperture size: F2.4; Focal Length: 52 mm; Sensor size: 1/3.6"; Pixel size: 1 μm Third camera: 12 MP (Ultra-wide) Specifications: Aperture size: F2.2; Pixel size: 1.12 μm Video recording: 3840x2160 (4K UHD) (60 fps), 1920x1080 (Full HD) (240 fps), 1280x720 (HD) (960 fps) Features: HDR, Continuous autofocus, EIS Front: 10 MP (EIS, HDR) Folded: 10 MP Video capture: 3840x2160 (4K UHD) (60 fps) DESIGN Size comparison Dimensions: 6.27 x 5.05 x 0.27 inches (159.2 x 128.2 x 6.9 mm) Folded: 159.2 x 68 x 16.8 mm Weight: 9.95 oz (282.0 g) Materials: Back: Glass; Frame: Aluminum Biometrics - Features and sensors that replace a traditional PIN or password as means of identification when unlocking your device. " style="box-sizing: border-box; display: inline-block; cursor: pointer;">Biometrics: 2D Face unlock, Fingerprint (touch) Keys: Right: Volume control, Lock/Unlock key Colors: Mystic black, Mystic bronze This device has different variants:   View all CELLULAR 5G: SA, NSA, Sub-6, mmWave LTE (FDD): Bands 2(1900), 3(1800), 4(AWS-1), 5(850), 7(2600), 8(900), 12(700 a), 13(700 c), 18(800 Lower), 19(800 Upper), 20(800 DD), 26(850+), 28(700 APT), 66(AWS-3) LTE (TDD): Bands 38(2600), 39(1900+), 40(2300), 41(2600+), 46, 48(3600) UMTS: Bands 5(850), 8(900), 2(1900), 1(2100) Data Speed: LTE-A Pro Cat 20 (2000/150 Mbit/s), HSDPA+ (4G) 42.2 Mbit/s, HSUPA 5.76 Mbit/s Dual SIM: Yes SIM type: Nano SIM, eSIM MULTIMEDIA Headphones: No 3.5mm jack Speakers: Earpiece, Multiple speakers Features: 32-Bit DAC, Dolby Atmos, aptX-HD, Dolby Digital, Dolby Digital Plus Screen mirroring: Wireless screen share Additional microphone(s): for Noise cancellation CONNECTIVITY & FEATURES Bluetooth: 5.0 Wi-Fi: 802.11 a, b, g, n, ac, ax (Wi-Fi 6), dual-band; MIMO, Wi-Fi Direct, Hotspot USB: Type-C (reversible), USB 3.1 Features: Charging, Headphones port, OTG, Video out Location - This field shows the positioning systems supported by the device. " style="box-sizing: border-box; display: inline-block; cursor: pointer;">Location: GPS, A-GPS, Glonass, Cell ID, Wi-Fi positioning Sensors: Accelerometer, Gyroscope, Compass, Hall (for flip covers), Barometer Other: NFC, ANT+