Peak load

Integrated stereo amplifier Rated continuation average output (Both channel operation, 20Hz - 20kHz) 220 W/ch (4ohms) 170 W/ch (8ohms) THD (both channel operation) 0.02% (4ohms - 16-ohm load) IM distortion 0.01% Frequency response Main amp input: 20Hz-20kHz+0 -0.2 dB (at the time of a rated continuation average output) 2Hz-150kHz+0 -3.0dB (at the time of 1W output) High Level input: 20Hz-20kHz+0 -0.2 dB (at the time of a rated continuation average output) Dumping factor 120 (8-ohm load, 50Hz) Input sensitivity/impedance (An Output power / EIA1W output) High Level input: 147mV/11.2mV/20kohm Balanced input: 147mV/11.2mV/40kohm Main input: 1.47V/112mV/20kohm An Output power/impedance Pre output: 1.47V/50 ohm (at the time of a rated continuation average output) Gain: Main input -> output: 28dB / High Level input -> Pre output: 20dB S/N, input conversion noise Input short-circuit and A-compensation EIA S/N At the time of a rated input S/N Input conversion noise Main amp input: 127dB -123dBV 103dB High Level input: 113dB -130dBV 82dB Balanced input: 90dB -108dBV 82dB Tone control Low-pitched sound (300Hz): ±10dB (50Hz) Loud sound (3kHz): ±10dB (20kHz) Loudness Compensation + 6dB (100Hz, Volume -30dB) Power meter Logarithm compression type peak level display dB scale and the output Direct reading at the time of 8-ohm load Load impedance 4ohm-16ohm Headphone jack Conformity impedance: 4ohms - 100ohms Power source AC230V, 50Hz/60Hz Power consumption 55W (at the time of no inputting) 350W (Electrical Appliance and Material Control Law) 585W (at the time of an 8-ohm load Output power) The maximum Dimensions Width 475x height 180x depth of 423mm Weight 23kg Attachment: Remote commander RC-20 Remote control system Infrared pulse system Power source DC 3V Battery AA type (SUM-3/R6) two pieces The maximum Dimensions Width 55x height 194x depth of 18mm Weight 100g (Battery includeded)

Welcome! For sale is Electro-Voice CPS4.10 apmlifier with 4 channels of each nominal output is 1000W. MSRP: 3200 US$ Amplifier was never used (just tested before i made this listing) and it is 100% operational. See more technical details below. Shipping We will ship to any location worldwide. Please send us message for shipping cost to your location. All customs fees are not included in the international shipping costs. Buyer is responsible for all customs fees.  Please contact us if you have any question regarding this item.  CPS4.10 This four-channel CPS amplifier from Electro-Voice features groundbreaking Class-D technology for maximum amp efficiency and minimized heat dissipation in 19-inch racks. Each channel individually provides transformerless, switchable output characteristics, which enable specific channels to achieve maximum drive. Power into 2 Ohms, 4 Ohms, 70V, or 100V line – no transformers are required. In Hi-Z operation (70V or 100V), a 50 Hz high-pass filter (HPF) provides protection against loudspeaker transformer saturation. Additionally, amplifier channels can be bridged in pairs for double output power. Each contractor-friendly, multi-channel CPS amplifier also features Phoenix-type connectors for inputs and outputs, pre-programmable power-on delay, easy power-on remote via contact closure, and rear level controls. A module slot for the RCM-810 remote control module provides control network functionality, allowing for remote system diagnostics and control via IRIS-Net software. In addition, using the RCM-810’s Variable Load Drive feature can tailor the amplifier’s output power to match every load from 2 Ohms up to 10 Ohms in steps of 0.1 Ohms. Features: - Class-D design for high-efficiency and low heat dissipation - Flexible matching for Low-Z and High-Z applications - Optional remote control via IRS-Net - Four-channel design in 2RU chassis Specifications: - Maximum Midband Output Power (THD=1%, 1kHZ): 4 x 1000W @ 2 ohms 4 x 1000W @ 4 ohms 4 x 1000W @ 70V 4 x 1000W @ 100V - Rated Output Power (THD 4 x 900W @ 2 ohms 4 x 900W @ 4 ohms 4 x 900W @ 70V 4 x 900W @ 100V  - Maximum Bridged Output Power (THD=1%, 1kHz) 2 x 2000W @ 4 ohms 2 x 2000W @ 8 ohms 2 x 2000W @ 140V 2 x 2000W @ 200V - Maximum RMS Voltage Swing (THD=1%, 1kHz, per channel): 100V - Power Bandwidth (THD=1% ref.1kHz, half power @ 4 ohms load): 10Hz-25kHz, 50Hz-25kHz  - Voltage Gain, ref. 1kHz: 32 dB (2ohm/4ohm mode), 33dB (70V mode), 36dB (100V mode)  - THD at rated output power (MBW=80kHz, 1kHz): - IMD-SMPTE, 60Hz, 7kHz: - DIM30, 3.15kHz, 15kHz: - Maximum Input Level: +21dBu - Crosstalk, ref. 1kHz at rated output power: - Frequency Response, ref. 1kHz: 10Hz-30kHz (+/-1dB) - Input Impedance, active balanced: 20k ohms - Damping Factor, 1khz, 8 ohms: >240 - Slew Rate: 28V/us - Output Noise, A-weighted: - Output Stage Topology: Class D - Power Consumption, 1/8 max. output power @ 4 ohms: 840W - Power Requirements: 220-240V, 50-60Hz or 120V, 50-60Hz or 100V, 50-60Hz - Protections: Audio Limiters, Temperature, DC, HF Short Circuit, Peak Current Limiters, Inrush Current Limiters, Turn-on Delay - Cooling: Front-to-rear, continuously variable fans - Ambient Temperature Limits: 40 to 105 deg. F - Safety Class: I - Dimensions (W x H x D): 19" x 34.7" x 16.6" - Weight: 24.6 lbs - Optional Accessories:  2-way internal X-Over cards, 24dB, LR, XHP-5 for 500Hz/XHP-8 for 800Hz RCM-810 IRIS-Net Control & Supervision Module Rear-Rackmount Kit RMK-15

12 Subwoofer Lotusline Neuf-65% du prix avant faillite haute gamme APG 6000Watts programme pro (détail ou évidence....) tout les caissons sont bien-sur fini avec leur hp Beyma 18 P1000 FE V2 neuf aussi... Une évidence bonne à rappeler. Haute Gamme APG lotusline et ArphoniA on était créer par Alain Pouillon Guilbert (APG) après qu'il est vendu APG il à souhaité répondre aux personnes les plus exigeantes en créant deux marques avant des évolutions des plus haute gamme. Faillite, je vend ces enceintes Haute gamme à - 65% du prix catalogue soit 2000€ pièces et 1500€ par pièce pour 6 pièces acheté. Le tarif catalogue était de 4870€ pièce. PS 141 DB SPL MAX Frequency range with processor (±3dB) 28 Hz to 80/250 Hz Sensitivity@1W/1m, f>80Hz 103 dB SPL Maximum continuous level at 1m, f>80Hz 137 dB SPL Peak level at 1m, f>65Hz 141 dB SPL Nominal impedance 4 OhmsCOMPONENTS Transducers 2 x 18" weatherproof loudspeaker Coil diameter 101.6 mm Type of load SIC™ Bass reflex Recommended amps 1500 to 3000W into 4 Ohms Peak programme 6000Watts AES 2400Watts no preset CONSTRUCTION AND CHARACTERISTICS Cabinet 18mm birch plywood with internal reinforcements Crossover The Crossover points shall be 80~120 Hz with 24 dB per octave Linkwitz-Riley characteristics. Finish Black, impact resistant structured and water paint coating Protection grill Acoustically transparent perforated steel, 1.8 mm thick Front face Black, woven, heavy duty fabric Connectors 2 x Speakon NL4MP Handles 4 wood integrated handles Dimensions (H x W x D) 516 x 1000 x 881 mm weight 84.2 kg 185.6 lbs Compatible avec du: Yorkville, Eminence, CROWN, AMCRON, RAM, DAS, Power, Christian Hell, FBT Ibiza, Elokance, Behringer, Camco, MARTIN, Mac MAH,Ableton / Adam Audio / Adam Hall / AFX Light / Akai / AKG / Allen & Heath / ALP / ALTO / Antari / Apogee / Arkaos / Art / Arturia / ASD / Audiopole / Ayrton / B and C / Behringer / Beyerdynamic / BMS / Boss/ BSS / BST / BST Pro / Cakewalk / Cameo/ Celemony / Celestion / Cerwin Vega / Chauvet / Chesley / Createled / Crest Audio / Crown / Dap Audio / Daslight / dB Technologies / DBX / Denon / Denon DJ / Denon Professional / Dynaudio / Ecler / ElectroVoice/ Elokance / Eminence / Evolite /Freevox / Gator / Genelec / Gewa / Ghost / HK Audio / HPA / JB System / JBL / LAB Gruppen / Laserworld / Lexicon / M AUDIO / MA lightning / Mackie/ Marshall / Martin / Martin Audio / Midas / Monster Cables / Montarbo / Native Instruments / Neumann / Neutrik / Novation / Numark / Ortofon / Osram / video hd full hd ski roland sony panasonic canon christie nec barco manfrotto tricaster espon laser table de mixage video film séminaires camera 4K 1080 p 1080i 50hz 60hz images par seconde Palmer / Pangolin / Pearl / Philips / Pioneer / Presonus / QSC / Ram Audio / Rane / RCf / Reloop / Rode / Rodec / Roland / Rush by Martin / Sabian / Samson /SE Electronics Materiel pro d'éclairage pour DJ, Orchestre, Concert, Groupes de Musique, Bar, Piano Bar, très largement supérieur à: Yorkville, Eminence, CROWN, AMCRON, RAM, DAS, Power, Christian Hell, FBT Ibiza, Elokance, Behringer, Camco, MARTIN, Mac MAH,Ableton / Adam Audio / Adam Hall / AFX Light / Akai / AKG / Allen & Heath / ALP / ALTO / Antari / Apogee / Arkaos / Art / Arturia / ASD / Audiopole / Ayrton / B and C / Behringer / Beyerdynamic / BMS / Boss/ BSS / BST / BST Pro / Cakewalk / Cameo/ Celemony / Celestion / Cerwin Vega / Chauvet / Chesley / Createled / Crest Audio / Crown / Dap Audio / Daslight / dB Technologies / DBX / Denon / Denon DJ / Denon Professional / Dynaudio / Ecler / ElectroVoice/ Elokance / Eminence / Evolite /Freevox / Gator / Genelec / Gewa / Ghost / HK Audio / HPA / JB System / JBL / LAB Gruppen / Laserworld / Lexicon / M AUDIO / MA lightning / Mackie/ Marshall / Martin / Martin Audio / Midas / Monster Cables / Montarbo / Native Instruments / Neumann / Neutrik / Novation / Numark / Ortofon / Osram / video hd ful

Vend mixette de reportage Sound Devices 442 + sacoche Petrol + 2 cables de connection camera 4 Balanced XLR Inputs The mixer's flexibility begins with it's 4 balanced XLR inputs. All 4 inputs are individually switchable to accept line or microphone level signals. Direct Outputs Every input features a dedicated output via TA3-male connectors. The direct outs are ideal for feeding individual channel signal to external devices. M-S Decoding Channels 1-2 can be linked for stereo capturing and M-S stereo monitoring. Channel 1 features a phase reverse switch. Variable Gain Continuously variable gain allows level contouring on every channel, resulting in higher signal to noise ratio. Variable Low-Cut Filter Continuously variable low-cut filter dials are located on each channel, eliminating low frequency noise between 80 - 240Hz Peak Limiting Input and output peak limiters eliminate signal over load that can cause noise and distortion.

12 Subwoofer Lotusline Neuf-70% du prix avant faillite haute gamme APG 6000Watts programme pro ATTENTION LES PHOTOS SONT QUE LES CAISSES SANS LES HAUTPARLEURS ! Ils sont bien sur montés + d'information 0+6 52 08 15 14 merci (détail ou évidence....) tout les caissons sont bien-sur fini avec leur hp Beyma 18 P1000 FE V2 neuf aussi... Une évidence bonne à rappeler. Haute Gamme APG lotusline et ArphoniA on était créer par Alain Pouillon Guilbert (APG) après qu'il est vendu APG il à souhaité répondre aux personnes les plus exigeantes en créant deux marques avant des évolutions des plus haute gamme. Faillite, je vend ces enceintes Haute gamme à - 70% du prix catalogue soit 1400€ pièce (a partir de 4 pièces) et 1800€ par pièce  acheté. Le tarif catalogue était de 4740€ pièce. Frequency range with processor (±3dB) 28 Hz to 80/250 Hz Sensitivity@1W/1m, f>80Hz 103 dB SPL Maximum continuous level at 1m, f>80Hz 137 dB SPL Peak level at 1m, f>65Hz 141 dB SPL Nominal impedance 4 OhmsCOMPONENTS Transducers 2 x 18" weatherproof loudspeaker Coil diameter 101.6 mm Type of load SIC™ Bass reflex Recommended amps 1500 to 3000W into 4 Ohms Peak programme 6000Watts AES 2400Watts no preset CONSTRUCTION AND CHARACTERISTICS Cabinet 18mm birch plywood with internal reinforcements Crossover The Crossover points shall be 80~120 Hz with 24 dB per octave Linkwitz-Riley characteristics. Finish Black, impact resistant structured and water paint coating Protection grill Acoustically transparent perforated steel, 1.8 mm thick Front face Black, woven, heavy duty fabric Connectors 2 x Speakon NL4MP Handles 4 wood integrated handles Dimensions (H x W x D) 516 x 1000 x 881 mm weight 84.2 kg 185.6 lbs Compatible avec du: Yorkville, Eminence, CROWN, AMCRON, RAM, DAS, Power, Christian Hell, FBT Ibiza, Elokance, Behringer, Camco, MARTIN, Mac MAH,Ableton / Adam Audio / Adam Hall / AFX Light / Akai / AKG / Allen & Heath / ALP / ALTO / Antari / Apogee / Arkaos / Art / Arturia / ASD / Audiopole / Ayrton / B and C / Behringer / Beyerdynamic / BMS / Boss/ BSS / BST / BST Pro / Cakewalk / Cameo/ Celemony / Celestion / Cerwin Vega / Chauvet / Chesley / Createled / Crest Audio / Crown / Dap Audio / Daslight / dB Technologies / DBX / Denon / Denon DJ / Denon Professional / Dynaudio / Ecler / ElectroVoice/ Elokance / Eminence / Evolite /Freevox / Gator / Genelec / Gewa / Ghost / HK Audio / HPA / JB System / JBL / LAB Gruppen / Laserworld / Lexicon / M AUDIO / MA lightning / Mackie/ Marshall / Martin / Martin Audio / Midas / Monster Cables / Montarbo / Native Instruments / Neumann / Neutrik / Novation / Numark / Ortofon / Osram / video hd full hd ski roland sony panasonic canon christie nec barco manfrotto tricaster espon laser table de mixage video film séminaires camera 4K 1080 p 1080i 50hz 60hz images par seconde Palmer / Pangolin / Pearl / Philips / Pioneer / Presonus / QSC / Ram Audio / Rane / RCf / Reloop / Rode / Rodec / Roland / Rush by Martin / Sabian / Samson /SE Electronics Materiel pro d'éclairage pour DJ, Orchestre, Concert, Groupes de Musique, Bar, Piano Bar, très largement supérieur à: Yorkville, Eminence, CROWN, AMCRON, RAM, DAS, Power, Christian Hell, FBT Ibiza, Elokance, Behringer, Camco, MARTIN, Mac MAH,Ableton / Adam Audio / Adam Hall / AFX Light / Akai / AKG / Allen & Heath / ALP / ALTO / Antari / Apogee / Arkaos / Art / Arturia / ASD / Audiopole / Ayrton / B and C / Behringer / Beyerdynamic / BMS / Boss/ BSS / BST / BST Pro / Cakewalk / Cameo/ Celemony / Celestion / Cerwin Vega / Chauvet / Chesley / Createled / Crest Audio / Crown / Dap Audio / Daslight / dB Technologies / DBX / Denon / Denon DJ / Denon Professional / Dynaudio / Ecler / ElectroVoice/ Elokance / Eminence / Evolite /Freevox / Gator / Genelec / Gewa / Ghost / HK Audio / HPA / JB System / JBL / LAB Gruppen / Laserworld / Lexicon / M AUDIO / MA lightning / Mackie/ Marshall / Martin / Martin Audio / Mi

Amplificateur - Tuner Radiola 603 / Platine K7 Radiola N5430 (Philips AH 603 / Philips 603 / Philips N5430) - tres rare ensemble ampli/tuner et lecteur K7.  Specifications Radiola 603 Tuning range: FM, MW, LW Power output: 30 watts per channel into 8Ω (stereo) Frequency response: 20Hz to 20kHz Input sensitivity: 2.5mV (MM), 150mV (DIN), 150mV (line) Output: 120mV (line), 0.25mV (DIN) Speaker load impedance: 8Ω (minimum) Specifications Radiola N5430 - Head Configuration - 2 Head Desiǥn - 4 Track / 2 Channel - Noise Reduction - Dolby-B Noise Reduction - MPX Filter - Connectivity - 2 Mono Microphone Inputs - DIN Input/Output Connector - Headphones - RCA Input/Output Connectors - Operation - Mechanical Transport Control - Memory Stop - Cue / Review - Preamplifier - Output-Level Control - Individual Input Level Controls - Display - 3-Digıt Mechanical Counter - Analog Needle Meters - Transport - Sìngle Capsŧan Transport - Belt Drive (Capsŧan) - Mechanical Tape Loading - Auto Shutoff - Indicators - Peak Indicator - Record - Cassette Back Lighting - Dolby B - Exterior - Front Loading - Orientation Right - Black Finish - General - Stereo - Tape - Chrome Tape Capabılity - Ferro-Chrome Tape Capabılity - Normal Tape Capabılity - Manual Tape Type Selection - Speed - 1⅞ ips - 4.76 cm/s En très bon état marche et esthétique.

PIONEER CT-656 STEREO CASETTE DECK 3 TETE SYSTEM DOLBY HX PRO PARFAIT ETAT.. État : "Occasion" Longeur 42cm. Largueur 30cm. Hauteur 13cm. Fonctionne parfaitement testé Si questions ou autres photos me contacter Emballé avec soins et rigueur eur hors france me contacter notice trouvable facilement sur internet. PIONEER CT-656 High end tape deck with 3 head technology Vintage cassette deck from the top brand Pioneer High quality. PIONEER CT-656 High end tape deck with 3 head technology Vintage cassette deck from the top brand Pioneer High quality workmanship and excellent fine Technology from the hifi heyday The optical condition is very good and well maintained! Small signs of use available! Technically, the tape works flawlessly! 100% at work! Technical specifications: connections Line (input): high level (LINE) 56 mV / input impedance: 56 kOhm Line (output): high level (LINE) 316 mV / output impedance: 5 kOhm Headphones: load impedance 8 ohms (volume max.) Technical specifications Tape heads: 3 PC-OCC-winding-hard-permalloy playback head / hard-permalloy-recording head combination x1 Erase head (ferrite) x 1 Motors: 2 1 x DC servo capstan motor, 1 x DC coil motor Wow and Flutter: 0.05% WRMS Belt types: Normal Type-I, Cromdioxide Type-II, Metal Type-IV Frequency response (+/- 6 dB): Normal band 15 to 20,000 Hz Chrome band 15 to 20,000 Hz Metal band 15 to 21,000 Hz Distortion factor: less than 0.7% (0 dB) S / N ratio Without Dolby:> 58 dB With Dolby B: + 10 dB (at 5 kHz) With Dolby C: + 19 dB (at 5 kHz) Auto reverse: no Track search: ± 15 tracks Dolby noise reduction: B + C MPX filter: Yes Fader: No. Pitch control: No. CD synchro recording: Yes (CD deck synchro with suitable Pioneer CD player) Special equipment Counter with two display modes (4-digit electronic counter) Level display switchable (normal / extended modulation range) Rear tape control option (automatic switching between sound source and recorded sound) Track search (+/- 15 tracks) Headphone output (with level control) Bias controller MPX filter Record mute to automatically insert spaces Automatic tape type selector Timer start function for recording and playback Repeat playback Dolby Noise Reduction System (B / C) Dolby HX Pro FL level meters (12 segments +1) with peak level memory funct Scope of delivery: 1 x CT-656 1 x English instruction manual 1 x TDK SA-C90 used 1 x professional packaging

Ampli de puissance Audio Research 150.2 en très bon état esthétique (intérieur et extérieur), ampli révisé pour le transmettre dans de bonnes conditions, fonctionnement parfait, façade irréprochable. 2 X 150 watts en 8 ohms   S'accorde avec préampli, tuner, dac, bloc mono, platine, lecteur, enceintes WELCOME OFFER NO SHIPPING OUTSIDE EUROPE Audio Research 150.2 power amplifier in very good aesthetic condition (interior and exterior), amplifier revised to transmit it in good conditions, perfect functioning, impeccable frontage. 2 X 150 watts into 8 ohms $2,495. Increased to $2,995 on December 1st 2005. POWER OUTPUT 150 watts per channel into 8 ohms, 300 watts per channel into 4 ohms, both channels driven, 1% THD POWER BANDWIDTH (-3dB points) 5Hz to 40 kHz into 8 ohms or 4 ohms FREQUENCY RESPONSE (-3dB points at 1W) 5 Hz to 120 kHz INPUT SENSITIVITY 1.4V RMS for rated output (27 dB Gain) single-ended or balanced INPUT IMPEDANCE 150K ohms single-ended, 300K ohms balanced differential OUTPUT TAPS - OUTPUT REGULATION 0.05 dB 8 ohm load into open circuit OVERALL NEGATIVE FEEDBACK 12dB DAMPING FACTOR 200 DISTORTION - SLEW RATE 15 V/µs. (20% maximum duty cycle) RISE TIME 2.0 µs HUM & NOISE 500 microvolts RMS (96 dB below rated output IHF A-weighted) POWER SUPPLY ENERGY STORAGE 144,000 µF total POWER REQUIREMENTS 100-125VAC 60Hz (200-250VAC 50Hz) 380 watts at rated output (150WPC 8 ohms), 750 watts at 300WPC 4 ohms, 800 watts maximum, 40 watts idle. OTHER Output polarity: Non-inverting from single-ended inputs. Balanced pin 2+ (IEC-268). Output current: 20 amps peak at protective shutdown. 12 VDC trigger and detachable AC power cord. DIMENSIONS 19" (48 cm) W (standard rack panel) x 5 ¼" (13.3 cm) H x 14 ¼" (36.2 cm) D (front panel back). Optional handles extend 1½" (3.8 cm) forward of the ¼" thick front panel. Output connectors extend 0.9" behind rear panel. WEIGHT 30.3 lbs. (13.8 kg) Net; 43.3 lbs. (19.7 kg) Shipping.