Plate energy

Product introduction: New original lamp beads, pure color temperature; A new scheme, LED cross-flow booster, supports 10-30V ultra-wide voltage input; Three pieces in one group, can be tailored freely! 15-24 inch universal omnipotence type; Adjustable brightness This lamp has 3 beads and 1 group. It can be cut freely according to actual requirements. For example, we usually use about 420 mm for 19 wide screen. Then we only need to cut it to the right length according to the rule of 3 beads and 1 group. It's very convenient. Cross-flow plate specification: 7cm*2cm (long*wide) constant current plate, also known as booster plate Specification of lamp bar: 490mm*4mm*2mm (length*width*height) (84 beads/strip) Input Voltage: 10V~30V Wide Voltage Characteristic: This product is a special lamp bar for original display. It has high brightness and can't be directly viewed. LED particles compact, high-density arrangement imported high-brightness LED patches Long life, designed for display, with a life of 100,000 hours Easy to install, double-sided glue can be used to paste in the original LCD slot of the display, or to paste elsewhere. Energy saving and power saving, power is only 8W. The power of the original four LCDs is generally 24 W. Modified LED Backlight Advantage: (1) The brightness of backlight lamp made of ordinary lamp tube is very dim when it is turned on. The brightness of backlight lamp made of LED does not need to wait until it is fully preheated. When it is turned on, the brightness of backlight lamp made of LED does not need to wait at all. (2) The backlight made of ordinary lamp tube consumes no energy, and the LED backlight lamp is both energy-saving and environment-friendly. (3) And life is more than three times as long as the backlight lamp made by ordinary lamp tube. There is no need to change the backlight for a lifetime. One investment will benefit all one's life. Packaging includes: 1Set (LED lamp bar * 2 + constant current plate + connecting wire)   Product introduction: New original lamp beads, pure color temperature; A new scheme, LED cross-flow booster, supports 10-30V ultra-wide voltage input; Three pieces in one group, can be tailored freely! 15-24 inch universal omnipotence type; Adjustable brightness This lamp has 3 beads and 1 group. It can be cut freely according to actual requirements. For example, we usually use about 420 mm for 19 wide screen. Then we only need to cut it to the right length according to the rule of 3 beads and 1 group. It's very convenient. Cross-flow plate specification: 7cm*2cm (long*wide) constant current plate, also known as booster plate Specification of lamp bar: 490mm*4mm*2mm (length*width*height) (84 beads/strip) Input Voltage: 10V~30V Wide Voltage Characteristic: This product is a special lamp bar for original display. It has high brightness and can't be directly viewed. LED particles compact, high-density arrangement imported high-brightness LED patches Long life, designed for display, with a life of 100,000 hours Easy to install, double-sided glue can be used to paste in the original LCD slot of the display, or to paste elsewhere. Energy saving and power saving, power is only 8W. The power of the original four LCDs is generally 24 W. Modified LED Backlight Advantage: (1) The brightness of backlight lamp made of ordinary lamp tube is very dim when it is turned on. The brightness of backlight lamp made of LED does not need to wait until it is fully preheated. When it is turned on, the brightness of backlight lamp made of LED does not need to wait at all. (2) The backlight made of ordinary lamp tube consumes no energy, and the LED backlight lamp is both energy-saving and environment-friendly. (3) And life is more than three times as long as the backlight lamp made by ordinary lamp tube. There is no need to change the backlight for a lifetime. One investment will benefit all one's life. Packaging includes: 1Set (LED lamp bar * 2 + constant current plate + connecting wire) Le 07-août-19 à 17:38:49 Paris, le vendeur a ajouté les informations suivantes:

Specification: LED Strip Size: 540mm x 4mm Driver board size:7x2cm Input:DC 10-30V OutPut:7.5V-9.6V Features: * The product of the original display-specific lights, high brightness, can not look directly * LED particles close, high-density arrangement bright LED SMD imports * Long life, is a display design, the life of 100,000 hours * Easy to install, use double-sided tape can be attached to the original LCD display tank, or posted elsewhere * Energy saving, power only 8W. Original four LCD power is generally 24W. Brief installation instructions: If your monitor is a high pressure plate, this pressure plate into a direct replacement driver board like if your monitor is one of the high-voltage power supply board, then: one version of the high-pressure electricity, find 12V (capacitance), then pull swap power supply with a multimeter to find and 12V (capacitance) is connected to the negative originals off, boost board then three lines 12V, ON, GND, 12V 12V positive electrode plate with high pressure booster is integrally connected to the board, GND with negative connected, oN even oN / OFF. it is simply the original high-voltage power supply is disconnected to replace the booster plate at the front end of the original pressure to take power. The following are the installation instructions for reference (for reference only): Easy modification steps: 1, open the metal frame: 2, cut the inner plastic protective frame angle: 3, out of the liquid crystal lamp: 4, insert the LED light bar Note, this modification method is simple, easy to light leakage. But it will destroy the border. Normal method: 1, open to protect the metal frame with a simple conversion step. 2. Remove the LCD glass panel (panel carefully on soft cable, such as careless easy to qualify and broadband) 3. Remove the plastic inner frame and lighthouse (Be careful not to get dirty fouling within the backlight assembly) 4. Remove the inner lamp lighthouse 5, LED light bar affixed inside the lighthouse 6, then restore the original removal steps carefully 7. Replace the glass panels and metal frame test 8, installed lights. Package Includes: 2x LED strips 1x Driver board 1x cable   Specification: LED Strip Size: 540mm x 4mm Driver board size:7x2cm Input:DC 10-30V OutPut:7.5V-9.6V Features: * The product of the original display-specific lights, high brightness, can not look directly * LED particles close, high-density arrangement bright LED SMD imports * Long life, is a display design, the life of 100,000 hours * Easy to install, use double-sided tape can be attached to the original LCD display tank, or posted elsewhere * Energy saving, power only 8W. Original four LCD power is generally 24W. Brief installation instructions: If your monitor is a high pressure plate, this pressure plate into a direct replacement driver board like if your monitor is one of the high-voltage power supply board, then: one version of the high-pressure electricity, find 12V (capacitance), then pull swap power supply with a multimeter to find and 12V (capacitance) is connected to the negative originals off, boost board then three lines 12V, ON, GND, 12V 12V positive electrode plate with high pressure booster is integrally connected to the board, GND with negative connected, oN even oN / OFF. it is simply the original high-voltage power supply is disconnected to replace the booster plate at the front end of the original pressure to take power. The following are the installation instructions for reference (for reference only): Easy modification steps: 1, open the metal frame: 2, cut the inner plastic protective frame angle: 3, out of the liquid crystal lamp: 4, insert the LED light bar Note, this modification method is simple, easy to light leakage. But it will destroy the border. Normal method: 1, open to protect the metal frame with a simple conversion step. 2. Remove the LCD glass panel (panel carefully on soft cable, such as careless easy to qualify and broadband) 3. Remove the plastic inner frame and lighthouse (Be careful not to get dirty fouling within the backlight assembly) 4. Remove the inner lamp lighthouse 5, LED light bar affixed inside the lighthouse 6, then restore the original removal steps carefully 7. Replace the glass panels and metal frame test 8, installed lights. Package Includes: 2x LED strips 1x Driver board 1x cable Le 02-avr.-19 à 09:52:29 Paris, le vendeur a ajouté les informations suivantes:

Specification: LED Strip Size: 540mm x 4mm Driver board size:7x2cm Input:DC 10-30V OutPut:7.5V-9.6V Features: * The product of the original display-specific lights, high brightness, can not look directly * LED particles close, high-density arrangement bright LED SMD imports * Long life, is a display design, the life of 100,000 hours * Easy to install, use double-sided tape can be attached to the original LCD display tank, or posted elsewhere * Energy saving, power only 8W. Original four LCD power is generally 24W. Brief installation instructions: If your monitor is a high pressure plate, this pressure plate into a direct replacement driver board like if your monitor is one of the high-voltage power supply board, then: one version of the high-pressure electricity, find 12V (capacitance), then pull swap power supply with a multimeter to find and 12V (capacitance) is connected to the negative originals off, boost board then three lines 12V, ON, GND, 12V 12V positive electrode plate with high pressure booster is integrally connected to the board, GND with negative connected, oN even oN / OFF. it is simply the original high-voltage power supply is disconnected to replace the booster plate at the front end of the original pressure to take power. The following are the installation instructions for reference (for reference only): Easy modification steps: 1, open the metal frame: 2, cut the inner plastic protective frame angle: 3, out of the liquid crystal lamp: 4, insert the LED light bar Note, this modification method is simple, easy to light leakage. But it will destroy the border. Normal method: 1, open to protect the metal frame with a simple conversion step. 2. Remove the LCD glass panel (panel carefully on soft cable, such as careless easy to qualify and broadband) 3. Remove the plastic inner frame and lighthouse (Be careful not to get dirty fouling within the backlight assembly) 4. Remove the inner lamp lighthouse 5, LED light bar affixed inside the lighthouse 6, then restore the original removal steps carefully 7. Replace the glass panels and metal frame test 8, installed lights. Package Includes: 2x LED strips 1x Driver board 1x cable   Specification: LED Strip Size: 540mm x 4mm Driver board size:7x2cm Input:DC 10-30V OutPut:7.5V-9.6V Features: * The product of the original display-specific lights, high brightness, can not look directly * LED particles close, high-density arrangement bright LED SMD imports * Long life, is a display design, the life of 100,000 hours * Easy to install, use double-sided tape can be attached to the original LCD display tank, or posted elsewhere * Energy saving, power only 8W. Original four LCD power is generally 24W. Brief installation instructions: If your monitor is a high pressure plate, this pressure plate into a direct replacement driver board like if your monitor is one of the high-voltage power supply board, then: one version of the high-pressure electricity, find 12V (capacitance), then pull swap power supply with a multimeter to find and 12V (capacitance) is connected to the negative originals off, boost board then three lines 12V, ON, GND, 12V 12V positive electrode plate with high pressure booster is integrally connected to the board, GND with negative connected, oN even oN / OFF. it is simply the original high-voltage power supply is disconnected to replace the booster plate at the front end of the original pressure to take power. The following are the installation instructions for reference (for reference only): Easy modification steps: 1, open the metal frame: 2, cut the inner plastic protective frame angle: 3, out of the liquid crystal lamp: 4, insert the LED light bar Note, this modification method is simple, easy to light leakage. But it will destroy the border. Normal method: 1, open to protect the metal frame with a simple conversion step. 2. Remove the LCD glass panel (panel carefully on soft cable, such as careless easy to qualify and broadband) 3. Remove the plastic inner frame and lighthouse (Be careful not to get dirty fouling within the backlight assembly) 4. Remove the inner lamp lighthouse 5, LED light bar affixed inside the lighthouse 6, then restore the original removal steps carefully 7. Replace the glass panels and metal frame test 8, installed lights. Package Includes: 2x LED strips 1x Driver board 1x cable Le 05-sept.-19 à 22:14:30 Paris, le vendeur a ajouté les informations suivantes:

Specification: LED Strip Size: 540mm x 4mm Driver board size:7x2cm Input:DC 10-30V OutPut:7.5V-9.6V Features: * The product of the original display-specific lights, high brightness, can not look directly * LED particles close, high-density arrangement bright LED SMD imports * Long life, is a display design, the life of 100,000 hours * Easy to install, use double-sided tape can be attached to the original LCD display tank, or posted elsewhere * Energy saving, power only 8W. Original four LCD power is generally 24W. Brief installation instructions: If your monitor is a high pressure plate, this pressure plate into a direct replacement driver board like if your monitor is one of the high-voltage power supply board, then: one version of the high-pressure electricity, find 12V (capacitance), then pull swap power supply with a multimeter to find and 12V (capacitance) is connected to the negative originals off, boost board then three lines 12V, ON, GND, 12V 12V positive electrode plate with high pressure booster is integrally connected to the board, GND with negative connected, oN even oN / OFF. it is simply the original high-voltage power supply is disconnected to replace the booster plate at the front end of the original pressure to take power. The following are the installation instructions for reference (for reference only): Easy modification steps: 1, open the metal frame: 2, cut the inner plastic protective frame angle: 3, out of the liquid crystal lamp: 4, insert the LED light bar Note, this modification method is simple, easy to light leakage. But it will destroy the border. Normal method: 1, open to protect the metal frame with a simple conversion step. 2. Remove the LCD glass panel (panel carefully on soft cable, such as careless easy to qualify and broadband) 3. Remove the plastic inner frame and lighthouse (Be careful not to get dirty fouling within the backlight assembly) 4. Remove the inner lamp lighthouse 5, LED light bar affixed inside the lighthouse 6, then restore the original removal steps carefully 7. Replace the glass panels and metal frame test 8, installed lights. Package Includes: 2x LED strips 1x Driver board 1x cable   Specification: LED Strip Size: 540mm x 4mm Driver board size:7x2cm Input:DC 10-30V OutPut:7.5V-9.6V Features: * The product of the original display-specific lights, high brightness, can not look directly * LED particles close, high-density arrangement bright LED SMD imports * Long life, is a display design, the life of 100,000 hours * Easy to install, use double-sided tape can be attached to the original LCD display tank, or posted elsewhere * Energy saving, power only 8W. Original four LCD power is generally 24W. Brief installation instructions: If your monitor is a high pressure plate, this pressure plate into a direct replacement driver board like if your monitor is one of the high-voltage power supply board, then: one version of the high-pressure electricity, find 12V (capacitance), then pull swap power supply with a multimeter to find and 12V (capacitance) is connected to the negative originals off, boost board then three lines 12V, ON, GND, 12V 12V positive electrode plate with high pressure booster is integrally connected to the board, GND with negative connected, oN even oN / OFF. it is simply the original high-voltage power supply is disconnected to replace the booster plate at the front end of the original pressure to take power. The following are the installation instructions for reference (for reference only): Easy modification steps: 1, open the metal frame: 2, cut the inner plastic protective frame angle: 3, out of the liquid crystal lamp: 4, insert the LED light bar Note, this modification method is simple, easy to light leakage. But it will destroy the border. Normal method: 1, open to protect the metal frame with a simple conversion step. 2. Remove the LCD glass panel (panel carefully on soft cable, such as careless easy to qualify and broadband) 3. Remove the plastic inner frame and lighthouse (Be careful not to get dirty fouling within the backlight assembly) 4. Remove the inner lamp lighthouse 5, LED light bar affixed inside the lighthouse 6, then restore the original removal steps carefully 7. Replace the glass panels and metal frame test 8, installed lights. Package Includes: 2x LED strips 1x Driver board 1x cable Le 04-sept.-19 à 18:24:09 Paris, le vendeur a ajouté les informations suivantes:

Product introduction: New original lamp beads, pure color temperature; A new scheme, LED cross-flow booster, supports 10-30V ultra-wide voltage input; Three pieces in one group, can be tailored freely! 15-24 inch universal omnipotence type; Adjustable brightness This lamp has 3 beads and 1 group. It can be cut freely according to actual requirements. For example, we usually use about 420 mm for 19 wide screen. Then we only need to cut it to the right length according to the rule of 3 beads and 1 group. It's very convenient. Cross-flow plate specification: 7cm*2cm (long*wide) constant current plate, also known as booster plate Specification of lamp bar: 490mm*4mm*2mm (length*width*height) (84 beads/strip) Input Voltage: 10V~30V Wide Voltage Characteristic: This product is a special lamp bar for original display. It has high brightness and can't be directly viewed. LED particles compact, high-density arrangement imported high-brightness LED patches Long life, designed for display, with a life of 100,000 hours Easy to install, double-sided glue can be used to paste in the original LCD slot of the display, or to paste elsewhere. Energy saving and power saving, power is only 8W. The power of the original four LCDs is generally 24 W. Modified LED Backlight Advantage: (1) The brightness of backlight lamp made of ordinary lamp tube is very dim when it is turned on. The brightness of backlight lamp made of LED does not need to wait until it is fully preheated. When it is turned on, the brightness of backlight lamp made of LED does not need to wait at all. (2) The backlight made of ordinary lamp tube consumes no energy, and the LED backlight lamp is both energy-saving and environment-friendly. (3) And life is more than three times as long as the backlight lamp made by ordinary lamp tube. There is no need to change the backlight for a lifetime. One investment will benefit all one's life. Packaging includes: 1Set (LED lamp bar * 2 + constant current plate + connecting wire)   Le 08-août-19 à 16:48:14 Paris, le vendeur a ajouté les informations suivantes:

Product introduction: New original lamp beads, pure color temperature; A new scheme, LED cross-flow booster, supports 10-30V ultra-wide voltage input; Three pieces in one group, can be tailored freely! 15-24 inch universal omnipotence type; Adjustable brightness This lamp has 3 beads and 1 group. It can be cut freely according to actual requirements. For example, we usually use about 420 mm for 19 wide screen. Then we only need to cut it to the right length according to the rule of 3 beads and 1 group. It's very convenient. Cross-flow plate specification: 7cm*2cm (long*wide) constant current plate, also known as booster plate Specification of lamp bar: 490mm*4mm*2mm (length*width*height) (84 beads/strip) Input Voltage: 10V~30V Wide Voltage Characteristic: This product is a special lamp bar for original display. It has high brightness and can't be directly viewed. LED particles compact, high-density arrangement imported high-brightness LED patches Long life, designed for display, with a life of 100,000 hours Easy to install, double-sided glue can be used to paste in the original LCD slot of the display, or to paste elsewhere. Energy saving and power saving, power is only 8W. The power of the original four LCDs is generally 24 W. Modified LED Backlight Advantage: (1) The brightness of backlight lamp made of ordinary lamp tube is very dim when it is turned on. The brightness of backlight lamp made of LED does not need to wait until it is fully preheated. When it is turned on, the brightness of backlight lamp made of LED does not need to wait at all. (2) The backlight made of ordinary lamp tube consumes no energy, and the LED backlight lamp is both energy-saving and environment-friendly. (3) And life is more than three times as long as the backlight lamp made by ordinary lamp tube. There is no need to change the backlight for a lifetime. One investment will benefit all one's life. Packaging includes: 1Set (LED lamp bar * 2 + constant current plate + connecting wire)   Le 24-août-19 à 07:41:09 Paris, le vendeur a ajouté les informations suivantes:

  Product introduction: New original lamp beads, pure color temperature; A new scheme, LED cross-flow booster, supports 10-30V ultra-wide voltage input; Three pieces in one group, can be tailored freely! 15-24 inch universal omnipotence type; Adjustable brightness This lamp has 3 beads and 1 group. It can be cut freely according to actual requirements. For example, we usually use about 420 mm for 19 wide screen. Then we only need to cut it to the right length according to the rule of 3 beads and 1 group. It's very convenient. Cross-flow plate specification: 7cm*2cm (long*wide) constant current plate, also known as booster plate Specification of lamp bar: 490mm*4mm*2mm (length*width*height) (84 beads/strip) Input Voltage: 10V~30V Wide Voltage Characteristic: This product is a special lamp bar for original display. It has high brightness and can't be directly viewed. LED particles compact, high-density arrangement imported high-brightness LED patches Long life, designed for display, with a life of 100,000 hours Easy to install, double-sided glue can be used to paste in the original LCD slot of the display, or to paste elsewhere. Energy saving and power saving, power is only 8W. The power of the original four LCDs is generally 24 W. Modified LED Backlight Advantage: (1) The brightness of backlight lamp made of ordinary lamp tube is very dim when it is turned on. The brightness of backlight lamp made of LED does not need to wait until it is fully preheated. When it is turned on, the brightness of backlight lamp made of LED does not need to wait at all. (2) The backlight made of ordinary lamp tube consumes no energy, and the LED backlight lamp is both energy-saving and environment-friendly. (3) And life is more than three times as long as the backlight lamp made by ordinary lamp tube. There is no need to change the backlight for a lifetime. One investment will benefit all one's life. Packaging includes: 1Set (LED lamp bar * 2 + constant current plate + connecting wire)     Le 17-oct.-19 à 17:39:40 Paris, le vendeur a ajouté les informations suivantes:

Product introduction: New original lamp beads, pure color temperature; A new scheme, LED cross-flow booster, supports 10-30V ultra-wide voltage input; Three pieces in one group, can be tailored freely! 15-24 inch universal omnipotence type; Adjustable brightness This lamp has 3 beads and 1 group. It can be cut freely according to actual requirements. For example, we usually use about 420 mm for 19 wide screen. Then we only need to cut it to the right length according to the rule of 3 beads and 1 group. It's very convenient. Cross-flow plate specification: 7cm*2cm (long*wide) constant current plate, also known as booster plate Specification of lamp bar: 490mm*4mm*2mm (length*width*height) (84 beads/strip) Input Voltage: 10V~30V Wide Voltage Characteristic: This product is a special lamp bar for original display. It has high brightness and can't be directly viewed. LED particles compact, high-density arrangement imported high-brightness LED patches Long life, designed for display, with a life of 100,000 hours Easy to install, double-sided glue can be used to paste in the original LCD slot of the display, or to paste elsewhere. Energy saving and power saving, power is only 8W. The power of the original four LCDs is generally 24 W. Modified LED Backlight Advantage: (1) The brightness of backlight lamp made of ordinary lamp tube is very dim when it is turned on. The brightness of backlight lamp made of LED does not need to wait until it is fully preheated. When it is turned on, the brightness of backlight lamp made of LED does not need to wait at all. (2) The backlight made of ordinary lamp tube consumes no energy, and the LED backlight lamp is both energy-saving and environment-friendly. (3) And life is more than three times as long as the backlight lamp made by ordinary lamp tube. There is no need to change the backlight for a lifetime. One investment will benefit all one's life. Packaging includes: 1Set (LED lamp bar * 2 + constant current plate + connecting wire) Le 19-janv.-20 à 06:09:19 Paris, le vendeur a ajouté les informations suivantes:

Specification: LED Strip Size: 540mm x 4mm Driver board size:7x2cm Input:DC 10-30V OutPut:7.5V-9.6V Features: * The product of the original display-specific lights, high brightness, can not look directly * LED particles close, high-density arrangement bright LED SMD imports * Long life, is a display design, the life of 100,000 hours * Easy to install, use double-sided tape can be attached to the original LCD display tank, or posted elsewhere * Energy saving, power only 8W. Original four LCD power is generally 24W. Brief installation instructions: If your monitor is a high pressure plate, this pressure plate into a direct replacement driver board like if your monitor is one of the high-voltage power supply board, then: one version of the high-pressure electricity, find 12V (capacitance), then pull swap power supply with a multimeter to find and 12V (capacitance) is connected to the negative originals off, boost board then three lines 12V, ON, GND, 12V 12V positive electrode plate with high pressure booster is integrally connected to the board, GND with negative connected, oN even oN / OFF. it is simply the original high-voltage power supply is disconnected to replace the booster plate at the front end of the original pressure to take power. The following are the installation instructions for reference (for reference only): Easy modification steps: 1, open the metal frame: 2, cut the inner plastic protective frame angle: 3, out of the liquid crystal lamp: 4, insert the LED light bar Note, this modification method is simple, easy to light leakage. But it will destroy the border. Normal method: 1, open to protect the metal frame with a simple conversion step. 2. Remove the LCD glass panel (panel carefully on soft cable, such as careless easy to qualify and broadband) 3. Remove the plastic inner frame and lighthouse (Be careful not to get dirty fouling within the backlight assembly) 4. Remove the inner lamp lighthouse 5, LED light bar affixed inside the lighthouse 6, then restore the original removal steps carefully 7. Replace the glass panels and metal frame test 8, installed lights. Package Includes: 2x LED strips 1x Driver board 1x cable   Le 24-déc.-18 à 13:37:18 Paris, le vendeur a ajouté les informations suivantes:

Specification: LED Strip Size: 540mm x 4mm Driver board size:7x2cm Input:DC 10-30V OutPut:7.5V-9.6V Features: * The product of the original display-specific lights, high brightness, can not look directly * LED particles close, high-density arrangement bright LED SMD imports * Long life, is a display design, the life of 100,000 hours * Easy to install, use double-sided tape can be attached to the original LCD display tank, or posted elsewhere * Energy saving, power only 8W. Original four LCD power is generally 24W. Brief installation instructions: If your monitor is a high pressure plate, this pressure plate into a direct replacement driver board like if your monitor is one of the high-voltage power supply board, then: one version of the high-pressure electricity, find 12V (capacitance), then pull swap power supply with a multimeter to find and 12V (capacitance) is connected to the negative originals off, boost board then three lines 12V, ON, GND, 12V 12V positive electrode plate with high pressure booster is integrally connected to the board, GND with negative connected, oN even oN / OFF. it is simply the original high-voltage power supply is disconnected to replace the booster plate at the front end of the original pressure to take power. The following are the installation instructions for reference (for reference only): Easy modification steps: 1, open the metal frame: 2, cut the inner plastic protective frame angle: 3, out of the liquid crystal lamp: 4, insert the LED light bar Note, this modification method is simple, easy to light leakage. But it will destroy the border. Normal method: 1, open to protect the metal frame with a simple conversion step. 2. Remove the LCD glass panel (panel carefully on soft cable, such as careless easy to qualify and broadband) 3. Remove the plastic inner frame and lighthouse (Be careful not to get dirty fouling within the backlight assembly) 4. Remove the inner lamp lighthouse 5, LED light bar affixed inside the lighthouse 6, then restore the original removal steps carefully 7. Replace the glass panels and metal frame test 8, installed lights. Package Includes: 2x LED strips 1x Driver board 1x cable Le 02-avr.-19 à 12:08:11 Paris, le vendeur a ajouté les informations suivantes:

Specification: LED Strip Size: 540mm x 4mm Driver board size:7x2cm Input:DC 10-30V OutPut:7.5V-9.6V Features: * The product of the original display-specific lights, high brightness, can not look directly * LED particles close, high-density arrangement bright LED SMD imports * Long life, is a display design, the life of 100,000 hours * Easy to install, use double-sided tape can be attached to the original LCD display tank, or posted elsewhere * Energy saving, power only 8W. Original four LCD power is generally 24W. Brief installation instructions: If your monitor is a high pressure plate, this pressure plate into a direct replacement driver board like if your monitor is one of the high-voltage power supply board, then: one version of the high-pressure electricity, find 12V (capacitance), then pull swap power supply with a multimeter to find and 12V (capacitance) is connected to the negative originals off, boost board then three lines 12V, ON, GND, 12V 12V positive electrode plate with high pressure booster is integrally connected to the board, GND with negative connected, oN even oN / OFF. it is simply the original high-voltage power supply is disconnected to replace the booster plate at the front end of the original pressure to take power. The following are the installation instructions for reference (for reference only): Easy modification steps: 1, open the metal frame: 2, cut the inner plastic protective frame angle: 3, out of the liquid crystal lamp: 4, insert the LED light bar Note, this modification method is simple, easy to light leakage. But it will destroy the border. Normal method: 1, open to protect the metal frame with a simple conversion step. 2. Remove the LCD glass panel (panel carefully on soft cable, such as careless easy to qualify and broadband) 3. Remove the plastic inner frame and lighthouse (Be careful not to get dirty fouling within the backlight assembly) 4. Remove the inner lamp lighthouse 5, LED light bar affixed inside the lighthouse 6, then restore the original removal steps carefully 7. Replace the glass panels and metal frame test 8, installed lights. Package Includes: 2x LED strips 1x Driver board 1x cable Le 01-avr.-19 à 13:08:56 Paris, le vendeur a ajouté les informations suivantes:

  Specification: LED Strip Size: 540mm x 4mm Driver board size:7x2cm Input:DC 10-30V OutPut:7.5V-9.6V Features: * The product of the original display-specific lights, high brightness, can not look directly * LED particles close, high-density arrangement bright LED SMD imports * Long life, is a display design, the life of 100,000 hours * Easy to install, use double-sided tape can be attached to the original LCD display tank, or posted elsewhere * Energy saving, power only 8W. Original four LCD power is generally 24W. Brief installation instructions: If your monitor is a high pressure plate, this pressure plate into a direct replacement driver board like if your monitor is one of the high-voltage power supply board, then: one version of the high-pressure electricity, find 12V (capacitance), then pull swap power supply with a multimeter to find and 12V (capacitance) is connected to the negative originals off, boost board then three lines 12V, ON, GND, 12V 12V positive electrode plate with high pressure booster is integrally connected to the board, GND with negative connected, oN even oN / OFF. it is simply the original high-voltage power supply is disconnected to replace the booster plate at the front end of the original pressure to take power. The following are the installation instructions for reference (for reference only): Easy modification steps: 1, open the metal frame: 2, cut the inner plastic protective frame angle: 3, out of the liquid crystal lamp: 4, insert the LED light bar Note, this modification method is simple, easy to light leakage. But it will destroy the border. Normal method: 1, open to protect the metal frame with a simple conversion step. 2. Remove the LCD glass panel (panel carefully on soft cable, such as careless easy to qualify and broadband) 3. Remove the plastic inner frame and lighthouse (Be careful not to get dirty fouling within the backlight assembly) 4. Remove the inner lamp lighthouse 5, LED light bar affixed inside the lighthouse 6, then restore the original removal steps carefully 7. Replace the glass panels and metal frame test 8, installed lights. Package Includes: 2x LED strips 1x Driver board 1x cable     Le 09-mai-19 à 05:43:10 Paris, le vendeur a ajouté les informations suivantes:

Specification: LED Strip Size: 540mm x 4mm Driver board size:7x2cm Input:DC 10-30V OutPut:7.5V-9.6V Features: * The product of the original display-specific lights, high brightness, can not look directly * LED particles close, high-density arrangement bright LED SMD imports * Long life, is a display design, the life of 100,000 hours * Easy to install, use double-sided tape can be attached to the original LCD display tank, or posted elsewhere * Energy saving, power only 8W. Original four LCD power is generally 24W. Brief installation instructions: If your monitor is a high pressure plate, this pressure plate into a direct replacement driver board like if your monitor is one of the high-voltage power supply board, then: one version of the high-pressure electricity, find 12V (capacitance), then pull swap power supply with a multimeter to find and 12V (capacitance) is connected to the negative originals off, boost board then three lines 12V, ON, GND, 12V 12V positive electrode plate with high pressure booster is integrally connected to the board, GND with negative connected, oN even oN / OFF. it is simply the original high-voltage power supply is disconnected to replace the booster plate at the front end of the original pressure to take power. The following are the installation instructions for reference (for reference only): Easy modification steps: 1, open the metal frame: 2, cut the inner plastic protective frame angle: 3, out of the liquid crystal lamp: 4, insert the LED light bar Note, this modification method is simple, easy to light leakage. But it will destroy the border. Normal method: 1, open to protect the metal frame with a simple conversion step. 2. Remove the LCD glass panel (panel carefully on soft cable, such as careless easy to qualify and broadband) 3. Remove the plastic inner frame and lighthouse (Be careful not to get dirty fouling within the backlight assembly) 4. Remove the inner lamp lighthouse 5, LED light bar affixed inside the lighthouse 6, then restore the original removal steps carefully 7. Replace the glass panels and metal frame test 8, installed lights. Package Includes: 2x LED strips 1x Driver board 1x cable Le 06-mai-19 à 09:56:09 Paris, le vendeur a ajouté les informations suivantes:

Specification: LED Strip Size: 540mm x 4mm Driver board size:7x2cm Input:DC 10-30V OutPut:7.5V-9.6V Features: * The product of the original display-specific lights, high brightness, can not look directly * LED particles close, high-density arrangement bright LED SMD imports * Long life, is a display design, the life of 100,000 hours * Easy to install, use double-sided tape can be attached to the original LCD display tank, or posted elsewhere * Energy saving, power only 8W. Original four LCD power is generally 24W. Brief installation instructions: If your monitor is a high pressure plate, this pressure plate into a direct replacement driver board like if your monitor is one of the high-voltage power supply board, then: one version of the high-pressure electricity, find 12V (capacitance), then pull swap power supply with a multimeter to find and 12V (capacitance) is connected to the negative originals off, boost board then three lines 12V, ON, GND, 12V 12V positive electrode plate with high pressure booster is integrally connected to the board, GND with negative connected, oN even oN / OFF. it is simply the original high-voltage power supply is disconnected to replace the booster plate at the front end of the original pressure to take power. The following are the installation instructions for reference (for reference only): Easy modification steps: 1, open the metal frame: 2, cut the inner plastic protective frame angle: 3, out of the liquid crystal lamp: 4, insert the LED light bar Note, this modification method is simple, easy to light leakage. But it will destroy the border. Normal method: 1, open to protect the metal frame with a simple conversion step. 2. Remove the LCD glass panel (panel carefully on soft cable, such as careless easy to qualify and broadband) 3. Remove the plastic inner frame and lighthouse (Be careful not to get dirty fouling within the backlight assembly) 4. Remove the inner lamp lighthouse 5, LED light bar affixed inside the lighthouse 6, then restore the original removal steps carefully 7. Replace the glass panels and metal frame test 8, installed lights. Package Includes: 2x LED strips 1x Driver board 1x cable Le 06-mai-19 à 07:54:08 Paris, le vendeur a ajouté les informations suivantes:

Specification: LED Strip Size: 540mm x 4mm Driver board size:7x2cm Input:DC 10-30V OutPut:7.5V-9.6V Features: * The product of the original display-specific lights, high brightness, can not look directly * LED particles close, high-density arrangement bright LED SMD imports * Long life, is a display design, the life of 100,000 hours * Easy to install, use double-sided tape can be attached to the original LCD display tank, or posted elsewhere * Energy saving, power only 8W. Original four LCD power is generally 24W. Brief installation instructions: If your monitor is a high pressure plate, this pressure plate into a direct replacement driver board like if your monitor is one of the high-voltage power supply board, then: one version of the high-pressure electricity, find 12V (capacitance), then pull swap power supply with a multimeter to find and 12V (capacitance) is connected to the negative originals off, boost board then three lines 12V, ON, GND, 12V 12V positive electrode plate with high pressure booster is integrally connected to the board, GND with negative connected, oN even oN / OFF. it is simply the original high-voltage power supply is disconnected to replace the booster plate at the front end of the original pressure to take power. The following are the installation instructions for reference (for reference only): Easy modification steps: 1, open the metal frame: 2, cut the inner plastic protective frame angle: 3, out of the liquid crystal lamp: 4, insert the LED light bar Note, this modification method is simple, easy to light leakage. But it will destroy the border. Normal method: 1, open to protect the metal frame with a simple conversion step. 2. Remove the LCD glass panel (panel carefully on soft cable, such as careless easy to qualify and broadband) 3. Remove the plastic inner frame and lighthouse (Be careful not to get dirty fouling within the backlight assembly) 4. Remove the inner lamp lighthouse 5, LED light bar affixed inside the lighthouse 6, then restore the original removal steps carefully 7. Replace the glass panels and metal frame test 8, installed lights. Package Includes: 2x LED strips 1x Driver board 1x cable Le 06-juin-19 à 13:31:05 Paris, le vendeur a ajouté les informations suivantes:

  Specification: LED Strip Size: 540mm x 4mm Driver board size:7x2cm Input:DC 10-30V OutPut:7.5V-9.6V Features: * The product of the original display-specific lights, high brightness, can not look directly * LED particles close, high-density arrangement bright LED SMD imports * Long life, is a display design, the life of 100,000 hours * Easy to install, use double-sided tape can be attached to the original LCD display tank, or posted elsewhere * Energy saving, power only 8W. Original four LCD power is generally 24W. Brief installation instructions: If your monitor is a high pressure plate, this pressure plate into a direct replacement driver board like if your monitor is one of the high-voltage power supply board, then: one version of the high-pressure electricity, find 12V (capacitance), then pull swap power supply with a multimeter to find and 12V (capacitance) is connected to the negative originals off, boost board then three lines 12V, ON, GND, 12V 12V positive electrode plate with high pressure booster is integrally connected to the board, GND with negative connected, oN even oN / OFF. it is simply the original high-voltage power supply is disconnected to replace the booster plate at the front end of the original pressure to take power. The following are the installation instructions for reference (for reference only): Easy modification steps: 1, open the metal frame: 2, cut the inner plastic protective frame angle: 3, out of the liquid crystal lamp: 4, insert the LED light bar Note, this modification method is simple, easy to light leakage. But it will destroy the border. Normal method: 1, open to protect the metal frame with a simple conversion step. 2. Remove the LCD glass panel (panel carefully on soft cable, such as careless easy to qualify and broadband) 3. Remove the plastic inner frame and lighthouse (Be careful not to get dirty fouling within the backlight assembly) 4. Remove the inner lamp lighthouse 5, LED light bar affixed inside the lighthouse 6, then restore the original removal steps carefully 7. Replace the glass panels and metal frame test 8, installed lights. Package Includes: 2x LED strips 1x Driver board 1x cable     Le 08-juil.-19 à 08:14:13 Paris, le vendeur a ajouté les informations suivantes:

Specification: LED Strip Size: 540mm x 4mm Driver board size:7x2cm Input:DC 10-30V OutPut:7.5V-9.6V Features: * The product of the original display-specific lights, high brightness, can not look directly * LED particles close, high-density arrangement bright LED SMD imports * Long life, is a display design, the life of 100,000 hours * Easy to install, use double-sided tape can be attached to the original LCD display tank, or posted elsewhere * Energy saving, power only 8W. Original four LCD power is generally 24W. Brief installation instructions: If your monitor is a high pressure plate, this pressure plate into a direct replacement driver board like if your monitor is one of the high-voltage power supply board, then: one version of the high-pressure electricity, find 12V (capacitance), then pull swap power supply with a multimeter to find and 12V (capacitance) is connected to the negative originals off, boost board then three lines 12V, ON, GND, 12V 12V positive electrode plate with high pressure booster is integrally connected to the board, GND with negative connected, oN even oN / OFF. it is simply the original high-voltage power supply is disconnected to replace the booster plate at the front end of the original pressure to take power. The following are the installation instructions for reference (for reference only): Easy modification steps: 1, open the metal frame: 2, cut the inner plastic protective frame angle: 3, out of the liquid crystal lamp: 4, insert the LED light bar Note, this modification method is simple, easy to light leakage. But it will destroy the border. Normal method: 1, open to protect the metal frame with a simple conversion step. 2. Remove the LCD glass panel (panel carefully on soft cable, such as careless easy to qualify and broadband) 3. Remove the plastic inner frame and lighthouse (Be careful not to get dirty fouling within the backlight assembly) 4. Remove the inner lamp lighthouse 5, LED light bar affixed inside the lighthouse 6, then restore the original removal steps carefully 7. Replace the glass panels and metal frame test 8, installed lights. Package Includes: 2x LED strips 1x Driver board 1x cable   Le 20-juil.-19 à 16:13:15 Paris, le vendeur a ajouté les informations suivantes:

Specification: LED Strip Size: 540mm x 4mm Driver board size:7x2cm Input:DC 10-30V OutPut:7.5V-9.6V Features: * The product of the original display-specific lights, high brightness, can not look directly * LED particles close, high-density arrangement bright LED SMD imports * Long life, is a display design, the life of 100,000 hours * Easy to install, use double-sided tape can be attached to the original LCD display tank, or posted elsewhere * Energy saving, power only 8W. Original four LCD power is generally 24W. Brief installation instructions: If your monitor is a high pressure plate, this pressure plate into a direct replacement driver board like if your monitor is one of the high-voltage power supply board, then: one version of the high-pressure electricity, find 12V (capacitance), then pull swap power supply with a multimeter to find and 12V (capacitance) is connected to the negative originals off, boost board then three lines 12V, ON, GND, 12V 12V positive electrode plate with high pressure booster is integrally connected to the board, GND with negative connected, oN even oN / OFF. it is simply the original high-voltage power supply is disconnected to replace the booster plate at the front end of the original pressure to take power. The following are the installation instructions for reference (for reference only): Easy modification steps: 1, open the metal frame: 2, cut the inner plastic protective frame angle: 3, out of the liquid crystal lamp: 4, insert the LED light bar Note, this modification method is simple, easy to light leakage. But it will destroy the border. Normal method: 1, open to protect the metal frame with a simple conversion step. 2. Remove the LCD glass panel (panel carefully on soft cable, such as careless easy to qualify and broadband) 3. Remove the plastic inner frame and lighthouse (Be careful not to get dirty fouling within the backlight assembly) 4. Remove the inner lamp lighthouse 5, LED light bar affixed inside the lighthouse 6, then restore the original removal steps carefully 7. Replace the glass panels and metal frame test 8, installed lights. Package Includes: 2x LED strips 1x Driver board 1x cable Le 17-juil.-19 à 09:19:16 Paris, le vendeur a ajouté les informations suivantes:

  Specification: LED Strip Size: 540mm x 4mm Driver board size:7x2cm Input:DC 10-30V OutPut:7.5V-9.6V Features: * The product of the original display-specific lights, high brightness, can not look directly * LED particles close, high-density arrangement bright LED SMD imports * Long life, is a display design, the life of 100,000 hours * Easy to install, use double-sided tape can be attached to the original LCD display tank, or posted elsewhere * Energy saving, power only 8W. Original four LCD power is generally 24W. Brief installation instructions: If your monitor is a high pressure plate, this pressure plate into a direct replacement driver board like if your monitor is one of the high-voltage power supply board, then: one version of the high-pressure electricity, find 12V (capacitance), then pull swap power supply with a multimeter to find and 12V (capacitance) is connected to the negative originals off, boost board then three lines 12V, ON, GND, 12V 12V positive electrode plate with high pressure booster is integrally connected to the board, GND with negative connected, oN even oN / OFF. it is simply the original high-voltage power supply is disconnected to replace the booster plate at the front end of the original pressure to take power. The following are the installation instructions for reference (for reference only): Easy modification steps: 1, open the metal frame: 2, cut the inner plastic protective frame angle: 3, out of the liquid crystal lamp: 4, insert the LED light bar Note, this modification method is simple, easy to light leakage. But it will destroy the border. Normal method: 1, open to protect the metal frame with a simple conversion step. 2. Remove the LCD glass panel (panel carefully on soft cable, such as careless easy to qualify and broadband) 3. Remove the plastic inner frame and lighthouse (Be careful not to get dirty fouling within the backlight assembly) 4. Remove the inner lamp lighthouse 5, LED light bar affixed inside the lighthouse 6, then restore the original removal steps carefully 7. Replace the glass panels and metal frame test 8, installed lights. Package Includes: 2x LED strips 1x Driver board 1x cable     Le 13-juil.-19 à 14:54:17 Paris, le vendeur a ajouté les informations suivantes:

  Specification: LED Strip Size: 540mm x 4mm Driver board size:7x2cm Input:DC 10-30V OutPut:7.5V-9.6V Features: * The product of the original display-specific lights, high brightness, can not look directly * LED particles close, high-density arrangement bright LED SMD imports * Long life, is a display design, the life of 100,000 hours * Easy to install, use double-sided tape can be attached to the original LCD display tank, or posted elsewhere * Energy saving, power only 8W. Original four LCD power is generally 24W. Brief installation instructions: If your monitor is a high pressure plate, this pressure plate into a direct replacement driver board like if your monitor is one of the high-voltage power supply board, then: one version of the high-pressure electricity, find 12V (capacitance), then pull swap power supply with a multimeter to find and 12V (capacitance) is connected to the negative originals off, boost board then three lines 12V, ON, GND, 12V 12V positive electrode plate with high pressure booster is integrally connected to the board, GND with negative connected, oN even oN / OFF. it is simply the original high-voltage power supply is disconnected to replace the booster plate at the front end of the original pressure to take power. The following are the installation instructions for reference (for reference only): Easy modification steps: 1, open the metal frame: 2, cut the inner plastic protective frame angle: 3, out of the liquid crystal lamp: 4, insert the LED light bar Note, this modification method is simple, easy to light leakage. But it will destroy the border. Normal method: 1, open to protect the metal frame with a simple conversion step. 2. Remove the LCD glass panel (panel carefully on soft cable, such as careless easy to qualify and broadband) 3. Remove the plastic inner frame and lighthouse (Be careful not to get dirty fouling within the backlight assembly) 4. Remove the inner lamp lighthouse 5, LED light bar affixed inside the lighthouse 6, then restore the original removal steps carefully 7. Replace the glass panels and metal frame test 8, installed lights. Package Includes: 2x LED strips 1x Driver board 1x cable     Le 13-juil.-19 à 04:59:04 Paris, le vendeur a ajouté les informations suivantes:

Specification: LED Strip Size: 540mm x 4mm Driver board size:7x2cm Input:DC 10-30V OutPut:7.5V-9.6V Features: * The product of the original display-specific lights, high brightness, can not look directly * LED particles close, high-density arrangement bright LED SMD imports * Long life, is a display design, the life of 100,000 hours * Easy to install, use double-sided tape can be attached to the original LCD display tank, or posted elsewhere * Energy saving, power only 8W. Original four LCD power is generally 24W. Brief installation instructions: If your monitor is a high pressure plate, this pressure plate into a direct replacement driver board like if your monitor is one of the high-voltage power supply board, then: one version of the high-pressure electricity, find 12V (capacitance), then pull swap power supply with a multimeter to find and 12V (capacitance) is connected to the negative originals off, boost board then three lines 12V, ON, GND, 12V 12V positive electrode plate with high pressure booster is integrally connected to the board, GND with negative connected, oN even oN / OFF. it is simply the original high-voltage power supply is disconnected to replace the booster plate at the front end of the original pressure to take power. The following are the installation instructions for reference (for reference only): Easy modification steps: 1, open the metal frame: 2, cut the inner plastic protective frame angle: 3, out of the liquid crystal lamp: 4, insert the LED light bar Note, this modification method is simple, easy to light leakage. But it will destroy the border. Normal method: 1, open to protect the metal frame with a simple conversion step. 2. Remove the LCD glass panel (panel carefully on soft cable, such as careless easy to qualify and broadband) 3. Remove the plastic inner frame and lighthouse (Be careful not to get dirty fouling within the backlight assembly) 4. Remove the inner lamp lighthouse 5, LED light bar affixed inside the lighthouse 6, then restore the original removal steps carefully 7. Replace the glass panels and metal frame test 8, installed lights. Package Includes: 2x LED strips 1x Driver board 1x cable Le 19-août-19 à 13:43:11 Paris, le vendeur a ajouté les informations suivantes:

  Specification: LED Strip Size: 540mm x 4mm Driver board size:7x2cm Input:DC 10-30V OutPut:7.5V-9.6V Features: * The product of the original display-specific lights, high brightness, can not look directly * LED particles close, high-density arrangement bright LED SMD imports * Long life, is a display design, the life of 100,000 hours * Easy to install, use double-sided tape can be attached to the original LCD display tank, or posted elsewhere * Energy saving, power only 8W. Original four LCD power is generally 24W. Brief installation instructions: If your monitor is a high pressure plate, this pressure plate into a direct replacement driver board like if your monitor is one of the high-voltage power supply board, then: one version of the high-pressure electricity, find 12V (capacitance), then pull swap power supply with a multimeter to find and 12V (capacitance) is connected to the negative originals off, boost board then three lines 12V, ON, GND, 12V 12V positive electrode plate with high pressure booster is integrally connected to the board, GND with negative connected, oN even oN / OFF. it is simply the original high-voltage power supply is disconnected to replace the booster plate at the front end of the original pressure to take power. The following are the installation instructions for reference (for reference only): Easy modification steps: 1, open the metal frame: 2, cut the inner plastic protective frame angle: 3, out of the liquid crystal lamp: 4, insert the LED light bar Note, this modification method is simple, easy to light leakage. But it will destroy the border. Normal method: 1, open to protect the metal frame with a simple conversion step. 2. Remove the LCD glass panel (panel carefully on soft cable, such as careless easy to qualify and broadband) 3. Remove the plastic inner frame and lighthouse (Be careful not to get dirty fouling within the backlight assembly) 4. Remove the inner lamp lighthouse 5, LED light bar affixed inside the lighthouse 6, then restore the original removal steps carefully 7. Replace the glass panels and metal frame test 8, installed lights. Package Includes: 2x LED strips 1x Driver board 1x cable -Nous acceptons seulement le paiement Paypal. - acheteurs   internationaux - veuillez   noter: a) les taxes et frais d'importation ne sont pas inclus dans le prix de l'article ou les frais d'expédition.  Ces   charges   sont   la   responsabilité   de   l' acheteur. b) Veuillez vérifier auprès du Bureau de douane de votre pays pour déterminer ce que ces coûts supplémentaires seront avant d'enchérir/acheter. * Nous ne pouvons pas expédier aux cases postales ou aux adresses d'APO/FPO Merci!     Le 23-août-19 à 18:22:31 Paris, le vendeur a ajouté les informations suivantes:

540mm LED Backlight Strip Kit For 24" inch Update CCFL LCD Screen To MonitWFFR Specification: LED Strip Size: 540mm x 4mm Driver board size:7x2cm Input:DC 10-30V OutPut:7.5V-9.6V Features: * The product of the original display-specific lights, high brightness, can not look directly * LED particles close, high-density arrangement bright LED SMD imports * Long life, is a display design, the life of 100,000 hours * Easy to install, use double-sided tape can be attached to the original LCD display tank, or posted elsewhere * Energy saving, power only 8W. Original four LCD power is generally 24W. Brief installation instructions: If your monitor is a high pressure plate, this pressure plate into a direct replacement driver board like if your monitor is one of the high-voltage power supply board, then: one version of the high-pressure electricity, find 12V (capacitance), then pull swap power supply with a multimeter to find and 12V (capacitance) is connected to the negative originals off, boost board then three lines 12V, ON, GND, 12V 12V positive electrode plate with high pressure booster is integrally connected to the board, GND with negative connected, oN even oN / OFF. it is simply the original high-voltage power supply is disconnected to replace the booster plate at the front end of the original pressure to take power. The following are the installation instructions for reference (for reference only): Easy modification steps: 1, open the metal frame: 2, cut the inner plastic protective frame angle: 3, out of the liquid crystal lamp: 4, insert the LED light bar Note, this modification method is simple, easy to light leakage. But it will destroy the border. Normal method: 1, open to protect the metal frame with a simple conversion step. 2. Remove the LCD glass panel (panel carefully on soft cable, such as careless easy to qualify and broadband) 3. Remove the plastic inner frame and lighthouse (Be careful not to get dirty fouling within the backlight assembly) 4. Remove the inner lamp lighthouse 5, LED light bar affixed inside the lighthouse 6, then restore the original removal steps carefully 7. Replace the glass panels and metal frame test 8, installed lights. Package Includes: 2x LED strips 1x Driver board 1x cable Le 22-août-19 à 10:39:35 Paris, le vendeur a ajouté les informations suivantes:

Specification: LED Strip Size: 540mm x 4mm Driver board size:7x2cm Input:DC 10-30V OutPut:7.5V-9.6V Features: * The product of the original display-specific lights, high brightness, can not look directly * LED particles close, high-density arrangement bright LED SMD imports * Long life, is a display design, the life of 100,000 hours * Easy to install, use double-sided tape can be attached to the original LCD display tank, or posted elsewhere * Energy saving, power only 8W. Original four LCD power is generally 24W. Brief installation instructions: If your monitor is a high pressure plate, this pressure plate into a direct replacement driver board like if your monitor is one of the high-voltage power supply board, then: one version of the high-pressure electricity, find 12V (capacitance), then pull swap power supply with a multimeter to find and 12V (capacitance) is connected to the negative originals off, boost board then three lines 12V, ON, GND, 12V 12V positive electrode plate with high pressure booster is integrally connected to the board, GND with negative connected, oN even oN / OFF. it is simply the original high-voltage power supply is disconnected to replace the booster plate at the front end of the original pressure to take power. The following are the installation instructions for reference (for reference only): Easy modification steps: 1, open the metal frame: 2, cut the inner plastic protective frame angle: 3, out of the liquid crystal lamp: 4, insert the LED light bar Note, this modification method is simple, easy to light leakage. But it will destroy the border. Normal method: 1, open to protect the metal frame with a simple conversion step. 2. Remove the LCD glass panel (panel carefully on soft cable, such as careless easy to qualify and broadband) 3. Remove the plastic inner frame and lighthouse (Be careful not to get dirty fouling within the backlight assembly) 4. Remove the inner lamp lighthouse 5, LED light bar affixed inside the lighthouse 6, then restore the original removal steps carefully 7. Replace the glass panels and metal frame test 8, installed lights. Package Includes: 2x LED strips 1x Driver board 1x cable Le 03-sept.-19 à 19:13:32 Paris, le vendeur a ajouté les informations suivantes:

Dell P2014H Large 20" Noir Ecran LCD DVI VGA avec 4-Port USB Hub P2014Ht J6HFT“cables offerts sur demande "   Occasion Garantie 6 Mois  Cable alimenation fournie + cable vga  Retrait sur pantin   Flexible viewing featuresThe Dell™ 20 Monitor – P2014H adjusts to comfortably fit the way you work and play. - Tilt, pivot, swivel and adjust the height of your monitor to maximize viewing comfort. - Easily transition from landscape to portrait orientation for optimal viewing of lengthy web pages with less scrolling. - Dell Display Manager is your one stop software application to manually adjust or auto assign optimal preset modes to specific software applications. VESA compatibilityThe VESA-compatible mounting plate makes it easy to install your monitor the way you want (mounting kits sold separately): - Dell Single Monitor Arm - Dell Dual Monitor Stand - Wall-mounting kit Multiple connectivity optionsA comprehensive range of analog and digital ports, and their accompanying cables, provides virtually all the connectivity options you'll need over the course of the day: - DisplayPort - VGA - DVI-D (excluding DVI-D cables) - 4 x USB Excellent screen clarityEvery detail is bright and clear with the crispness of LED backlighting. - HD 1600 x 900 resolution at 60Hz (max.) - 250 cd/m² brightness (typical) - 83% color gamut1 (typical) Color clarity and consistency across an ultra-wide viewing angleThe in-plane switching technology offers clear images with consistent and accurate colors across a wide 16:9 aspect ratio that features: - An ultra-wide 178°/178° viewing angle - Excellent picture quality with high 2 million:1 dynamic contrast ratio (typical) for deep blacks, bright whites and outstanding details - 8ms (gray to gray) response time (typical) for clean, fluid motion Environment-conscious designThe Dell 20 Monitor – P2014H meets the latest regulatory and environmental standards. - ENERGY STAR® Qualified - EPEAT® Gold Rated - TCO Certified Displays - China Energy Label (CEL) compliant The P2014H is BFR/PVC-free (excluding external cables) with more than 25 percent post-consumer recycled plastics in the chassis.Energy-efficient designWith 20W normal-operation power consumption (typical) and less than 0.3W power consumption in active-off mode, the P2014H can help keep your energy costs down. Manage power consumption wisely with PowerNap, enabled through the Dell Display Manager to either dim the monitor to the minimum brightness level or put it into sleep mode when it is not in use   Complete your Dell Monitor experience Your Dell 20 Monitor – P2014H is just the start. Look for these great additions when finalizing your purchase.

Description La marque vous parle Fiche technique Questions / Réponses E-LOSTBAG Premium™ se place à l'intérieur de votre bagage pour éviter toute altération externe lors de l'acheminement de ce dernier et se connecte avec votre smartphone pour une utilisation simple et efficace.Origine: Suisse Livraison gratuite ! DÉCOUVREZ... E-LOSTBAG PREMIUM !E-LOSTBAG Premium™ - Luggage Smart TrackerLe E-LOSTBAG Premiu Voir toute la description Type de recharge Rechargeable Marque E-Lostbag Voir toute la fiche technique 124,79 €   € Qu’est-ce que l’éco-participation ? Le prix de cet article inclut l’Eco-participation. L’éco-participation correspond à la contribution financière du consommateur à la collecte, à la réutilisation et au recyclage des équipements électriques et électroniques et des meubles en fin de vie. Son montant est déterminé selon le produit et son type de traitement (pour la DEEE) et selon un barème en fonction du type de meuble et de son poids (pour l’éco-participation sur le mobilier). Pour l’éco-participation sur les équipements électriques et électroniques: Les équipements informatiques: Ordinateurs, imprimantes, claviers… Les équipements de télécommunication: téléphones, fax, répondeurs… Les équipements images et sons: chaînes hifi, caméscopes… Les jouets et équipements de loisirs et sport: consoles de jeux, trains ou voitures électriques… Les sources lumineuses à collecte et recyclage spécifique: lampes à économie d’énergie, néons… L’électroménager: machines à laver, réfrigérateurs, tables de cuisson… Dans le cadre de l’achat d’un appareil électrique et électronique neuf, vous pouvez nous restituer gratuitement votre ancien appareil. Dans un délai de 7 jours suivant le passage de votre commande, connectez-vous à votre espace client, et dans la section "Retourner un produit", sélectionnez "Reprendre mon ancien matériel". Pour l’éco-participation sur le mobilier : Les meubles de salon/séjour/salle à manger, Les meubles d’appoint, Les meubles de chambre à coucher, La literie, Les meubles de bureau, Les meubles de cuisine, Les meubles de salle de bains, Les meubles de jardin, Les sièges, Le mobilier technique, commercial et de collectivité... Participons au recyclage et à la revalorisation des équipements électroniques et électriques et des meubles en fin de vie. En savoir +. Ou 3 fois 42,55€ (avec frais) avec Cofidis Livré chez vous à partir du 19/08/2022 Livraison Offerte Détail des modes de livraison × Modes de livraison Livraison standard à domicile Livré entre le 19/08/2022 et 22/08/2022 Livraison gratuite en stock 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 Je fonce Ce produit n'est pas disponible, notre équipe fait le maximum pour qu'il le soit bientôt. Inscrivez-vous pour être tenu au courant. Créer une alerte Produit neuf Vendu et expédié par Onefantasticshop 0 avis 1 Neuf à partir de 124,79 € × Autres offres TOUT NEUF SECONDE VIE 124,79 € Onefantasticshop - Neuf Livraison gratuite 124,79 € Onefantasticshop - Neuf Livraison gratuite Il n'y a actuellement aucune offre d'occasion pour ce produit. Besoin d'aide pour votre achat ? Appelez-nous: du lundi au vendredi de 9h à 20h et le samedi de 9h à 18h (hors jours fériés). 2022-08-06 10:08:14 Publicité Description La marque vous parle Fiche technique Avis clients - Les avis sont publiés et conservés pendant une durée de cinq ans ; - Les avis publiés font l'objet d'une modération depuis la plateforme Avis Vérifiés labellisée AFNOR garantissant - l'authenticité et la transparence des avis publiés (positifs ou négatifs) ; - Les avis ne sont pas modifiables: si un client souhaite modifier son avis, il doit contacter notre partenaire Avis Vérifiés afin de supprimer l'avis existant, et en publier un nouveau"> Questions / Réponses Description - Traqueur GPS connecté - E-Lostbag - Tracker E-Lostbag Premium Pour Bagage Points forts E-Lostbag Tracker E-Lostbag Premium Pour Bagage DÉCOUVREZ... E-LOSTBAG PREMIUM ! E-LOSTBAG Premium™ - Luggage Smart Tracker Le E-LOSTBAG Premium™ est un tracker pour bagage basé sur la technologie E-LOSTBAG Standard. Il vous permet de rendre identifiable votre bagage auprès de toutes les compagnies aériennes grâce à nos partenariats uniques avec les services Lost et Found (services ayant la gestion des bagages perdus dans les lieux de transports). E-LOSTBAG Premium™ se place à l'intérieur de votre bagage pour éviter toute altération externe lors de l'acheminement de ce dernier et se connecte avec votre smartphone pour une utilisation simple et efficace. E-LOSTBAG Premium™ permet toujours de rendre identifiable n'importe quel bagage. Cependant il intègre une nouvelle technologie, le Bluetooth Low Energy, qui permet ainsi au propriétaire d'avoir plus d'interactivité avec son bagage. Le E-LOSTBAG Premium™ permet notamment de savoir si son bagage est à proximité, alerter son propriétaire lorsque son bagage est en approche sur le carrousel à bagage, faire sonner le bagage afin de le repérer plus facilement et éviter les erreurs. Mais sa plus grande force réside dans l'interaction avec le réseau NoL™ (Network Of Luggage) et permet ainsi de fournir une position GPS sans aucun abonnement. Enregistrez votre identifiant LPN (Licence Plate Number) Selon la norme IATA, lorsque vous enregistrez votre bagage au comptoir d'un aéroport, le DCS (departure control system) génère un numéro d'identification, le LPN (Licence Plate Number). Ce numéro permet une traçabilité interne de votre bagage grâce à des échanges entre les acteurs du transport. E-LOSTBAG Premium™ intègre la norme IATA pour l'enregistrement des numéros d'identification LPN et vous permet de lier votre E-LOSTBAG Premium ™ avec ce dernier. Cette liaison permet de renforcer la traçabilité de votre bagage en cas de perte. Recevez une alerte lorsque votre bagage arrive sur le carrousel ou s'il n'est plus à proximité (vol, perte, oublis) Votre bagage vous informe lorsqu'il arrive sur le carrousel. E-LOSTBAG Premium™ peut également sonner pour vous éviter les erreurs de bagages identiques. E-LOSTBAG Premium™ vous informe lorsque votre bagage se trouve à plus de 15 mètres de vous. Ainsi ce dernier vous alerte en cas de vols, oublie, perte...

Ecrans professionnels n'ayant servi que 48 heures, pour un évènement. Très bonnes notes sur les sites pros. 3 écrans équipés de supports, 3 autres manquants. PROLITE  XU2390HS-B1 Moniteur 23" avec dalle IPS et façade ultra plate Le ProLite XU2390HS est un écran 23" LCD au rétro-éclairage LED, équipé d'une dalle IPS, technologie la plus aboutie disponible sur le marché. Il offre une reproduction des couleurs fidèle et précise, avec des angles de vision larges (178°/178°) et un temps de réponse rapide de 5 ms (noir à noir). Le XU390HS est un écran « full HD », avec un ratio de contraste dynamique de 5.000.000:1 et une luminosité de 250 cd/m² assurant à son utilisateur une image claire et vive. Le ProLite XU2390HS fournira d'excellentes performances pour la retouche de photos, le développement de sites internet, ou la bureautique standard. Il sera également parfaitement adapté pour une configuration multi-écrans, pour des applications en affichage dynamique ou bureautique. Technologie de dalle IPS Diagonale 23" (58 cm) Définition 1920 x 1080 (FHD) Format Large (16:9) Pitch 0,265mm Fréquence de rafraîchissement maximale 60 Hz Angles de vision (H°/V°) 178°/178° Luminosité 250 cd/m² Rapport de contraste natif 1000:1 Rapport de contraste dynamique 10 000 000:1 Temps de réponse (gris-à-gris) 5 ms Dalle anti-reflets Oui   SPÉCIFICITÉS GAMING 3D Non   CONNECTIQUE VIDÉO VGA VGA (x1) DVI DVI-D (x1) HDMI HDMI (x1)   CONNECTIQUE DIVERSE Haut-parleurs intégrés 2 x 2 W   ERGONOMIE Inclinaison avant/arrière Oui Détachable Oui Montage VESA 100 x 100 mm   CARACTÉRISTIQUES PHYSIQUES Couleur cadre Noir Dimensions sur pied 532,5 x 387,5 x 180 Poids avec pied 4 kg Accessoires et fonctions Livré avec câble DVI, câble audio   CARACTÉRISTIQUES ÉNERGÉTIQUES Bloc d'alimentation intégré Oui Consommation En fonctionnement: 24W En veille Label énergétique Energy Star 6.0 / TCO 6.0

IIYAMA ProLite XU2390HS 23" Full HD IPS Noir écran plat de PC Consulter nos évaluations IIYAMA ProLite XU2390HS 23" Full HD IPS Noir écran plat de PC Disponibilité: en stock Référence: XU2390HS-B1 Moniteur 23" avec dalle IPS et façade ultra plate Le ProLite XU2390HS est un écran 23" LCD au rétro-éclairage LED, équipé d'une dalle IPS, technologie la plus aboutie disponible sur le marché. Il offre une reproduction des couleurs fidèle et précise, avec des angles de vision larges (178°/178°) et un temps de réponse rapide de 5 ms (noir à noir). Le XU390HS est un écran « full HD », avec un ratio de contraste dynamique de 5.000.000:1 et une luminosité de 250 cd/m² assurant à son utilisateur une image claire et vive. Le ProLite XU2390HS fournira d'excellentes performances pour la retouche de photos, le développement de sites internet, ou la bureautique standard. Il sera également parfaitement adapté pour une configuration multi-écrans, pour des applications en affichage dynamique ou bureautique. Écran Taille de l'écran 58,4 cm (23") Luminosité de l'écran 250 cd/m² Résolution de l'écran 1920 x 1080 pixels Temps de réponse 5 ms Écran LED Type HD Full HD Technologie d'affichage IPS Résolutions graphiques prises en charge 1920 x 1080 (HD 1080) Taux de contraste 1000:1 Angle de vision horizontal 178° Angle de vision vertical 178° Nombre de couleurs affichées 16,78 millions de couleurs Ratio de format d'image 16:9 Compatibilité 3D Non Rapport de contraste (dynamique) 5000000:1 Rapport d'aspect 16:9 Diagonale verrerie (cm) 58,42 cm Pas de pixel 0,265 x 0,265 mm Domaine de numérisation horizontale 24 - 80 kHz Fréquence de balayage vertical 56 - 75 Hz Taille visualisable horizontale 50,9 cm Taille visualisable verticale 28,6 cm Taille visualisable diagonale 58,4 cm Sync. Séparée H/V Oui HDCP Oui Modes vidéo pris en charge 1080p Forme d'écran Plat Multimedia Haut-parleurs intégrés Oui Appareil photo intégré Non Synthoniseur TV intégré Non Nombre de haut-parleurs 2 Puissance évaluée de RMS 4 W Design Couleur du produit Noir Performance Prise en charge du système d'exploitation Windows Windows 2000,Windows 7 Home Basic,Windows 7 Home Basic x64,Windows 7 Home Premium,Windows 7 Home Premium x64,Windows 7 Professional,Windows 7 Professional x64,Windows 7 Starter,Windows 7 Starter x64,Windows 7 Ultimate,Windows 7 Ultimate x64,Windows 95,Windows 98,Windows ME,Windows Vista Business,Windows Vista Business x64,Windows Vista Enterprise,Windows Vista Enterprise x64,Windows Vista Home Basic,Windows Vista Home Basic x64,Windows Vista Home Premium,Windows Vista Home Premium x64,Windows Vista Ultimate,Windows Vista Ultimate x64,Windows XP Home,Windows XP Home x64,Windows XP Professional,Windows XP Professional x64 Client léger Thin client installé Non Connectivité Nombre de ports VGA (D-Sub) 1 Port DVI Oui Quantité de ports HDMI 1 Quantité de ports DVI-D 1 Entrée audio Oui Secteur d'entrée d'alimentation Oui Ergonomie Port de câble antivol Kensington Montage VESA Oui Réglage de la hauteur Non Bouton marche/arrêt intégré Oui Norme VESA 100 x 100 mm Pivotant Non Ajustement de l'inclinaison Oui Angle d'inclinaison -4 - 20° Affichage à l'écran (OSD) Oui Pivot Non Nombre de langues OSD 9 Affichage multilingue à l'écran CHI (SIMPL), Anglais, Espagnol, Français, Italien, JPN, Portugais, Russe Plug and Play Oui Gestion d'énergie Consommation d'énergie (mode veille) 0,5 W Consommation électrique (typicale) 24 W Consommation annuelle d'énergie 32 kWh Classe d'efficacité énergétique A Tension d'entrée AC 100 - 240 Fréquence d'entrée AC 50/60 Conditions environnementales Température d'opération 5 - 35 °C Température hors fonctionnement -20 - 60 °C Taux d'humidité de fonctionnement 10 - 80% Taux d'humidité relative (stockage) 5 - 85% Certificat Certifié Energy Star Oui Conformité EPEAT Argent Certification TCO, CE, TÜV-Bauart, VCCI-B, EAC Poids et dimensions Largeur 532,5 mm Profondeur 44 mm Hauteur 317,5 mm Largeur appareil (support inclus) 532,5 mm Profondeur (support inclus) 180 mm Hauteur (support inclus) 387,5 mm Poids avec pied 4 kg Contenu de l'emballage Stand inclus Oui Câbles inclus Secteur, Audio (3,5 mm), DVI Guide de démarrage rapide Oui

Dell E176FP -17 pouces -  bon état général, article d'occasion pouvant présenter des traces  d’usage. - câbles d'alimentation et VGA fournis.. Garantie de 3 mois. Informations générales sur le produit Marque DELL Nom du produit Dell e176fp: TFT 17 / Noir / Dalle Plate Catégorie ECRAN ORDINATEUR Général Type d'affichage Ecran LCD / matrice active TFT Résolution native 1280 x 1024 Temps de réponse 12 ms Rapport de contraste 450:1 Luminosité 300 cd/m² Prise en charge des couleurs 16,2 millions de couleurs Couleur Gris anthracite Revêtement de l'écran Anti-éblouissement, revêtement dur Angle de visualisation horizontale +70 / -70 Angle de visualisation verticale +60 / -60 Dimensions (LxPxH) 37.5 cm x 13.7 cm x 38 cm Poids 4 kg Fréquence de réactualisation verticale 76 Hz Fréquence de réactualisation horizontale 81 kHz Surface visible 17" Taille de la diagonale 17" Densité par pixel 0.264 mm Connectivité Interfaces 1 x VGA - 15 broches HD D-Sub (HD-15) Mécanique Interface de montage VESA 100 x 100 mm Divers Caractéristiques Fente de verrouillage de sécurité (câble de verrouillage vendu séparément), montage mural possible Normes de conformité TUV GS, C-Tick, BSMI, VCCI Class B ITE, GOST, EN 60950, EN 61000-3-2, EN55022, ICES-003, IEC950, ISO 13406-2, NEMKO, NOM, SABS, SASO, TCO '99, TUV S, UL 1950, EN 61000-3-3, EN55024, FCC Part 15 B, CCC, PSB, MIC, SII Alimentation Tension requise CA 120/230 V (50/60 Hz) Normes environnementales Certifié ENERGY STAR Oui Caractéristiques d’environnement Taux d'humidité en fonctionnement 10 - 80% Température maximale de fonctionnement 35 °C Température minimale de fonctionnement 5 °C                                              Livraison  : - Groupez vos achats pour économiser sur les frais de port. - Livraison mondial relay  par défaut au point relais le plus proche de chez vous, ou choisissez et communiquez nous en un autre:   cliquez ici. -  Livraison par colissimo du lundi au vendredi. -  Livraison par mondial relay du mardi au samedi. - Assurance avec mondial relay disponible: 3,50 euros. Paiement  :                                 -  paypal, virement bancaire, chèque personnel, cartes bancaires via paypal - Évaluation  : Satisfaire nos clients est notre engagement, pour toutes questions ou réclamations, n'hésitez pas à nous contacter, nous trouverons une réponse ou une solution adaptée à vos besoins. Nous laissons une évaluation positive automatiquement dès réception du paiement en gage de notre confiance.  Contact:   Une question, un renseignement, n'hésitez pas à nous contacter en cliquant  ici,  N'oubliez pas de m'ajouter à votre liste de favoris  !

IIYAMA ProLite XU2390HS LED display 58,4 cm (23") 1920 x 1080 pixels Full HD Noir Consulter nos évaluations IIYAMA ProLite XU2390HS LED display 58,4 cm (23") 1920 x 1080 pixels Full HD Noir Disponibilité: en stock Référence: XU2390HS-B1 Moniteur 23" avec dalle IPS et façade ultra plate Le ProLite XU2390HS est un écran 23" LCD au rétro-éclairage LED, équipé d'une dalle IPS, technologie la plus aboutie disponible sur le marché. Il offre une reproduction des couleurs fidèle et précise, avec des angles de vision larges (178°/178°) et un temps de réponse rapide de 5 ms (noir à noir). Le XU390HS est un écran « full HD », avec un ratio de contraste dynamique de 5.000.000:1 et une luminosité de 250 cd/m² assurant à son utilisateur une image claire et vive. Le ProLite XU2390HS fournira d'excellentes performances pour la retouche de photos, le développement de sites internet, ou la bureautique standard. Il sera également parfaitement adapté pour une configuration multi-écrans, pour des applications en affichage dynamique ou bureautique. Écran Taille de l'écran 58,4 cm (23") Luminosité de l'écran (typique) 250 cd/m² Résolution de l'écran 1920 x 1080 pixels Format d'image 16:9 Temps de réponse 5 ms Compatibilité 3D Non Type de panneau IPS Type HD Full HD Technologie d'affichage LED Forme d'écran Plat Résolutions graphiques prises en charge 1920 x 1080 (HD 1080) Taux de contraste 1000:1 Angle de vision horizontal 178° Angle de vision vertical 178° Nombre de couleurs affichées 16,78 millions de couleurs Modes vidéo pris en charge 1080p Rapport de contraste (dynamique) 5000000:1 Diagonale d'écran (cm) 58,42 cm Pas de pixel 0,265 x 0,265 mm Domaine de numérisation horizontale 24 - 80 kHz Fréquence de balayage vertical 56 - 75 Hz Taille visualisable horizontale 50,9 cm Taille visualisable verticale 28,6 cm Taille visualisable diagonale 58,4 cm Sync. Séparée H/V Oui Performance Prise en charge du système d'exploitation Windows Windows 2000,Windows 7 Home Basic,Windows 7 Home Basic x64,Windows 7 Home Premium,Windows 7 Home Premium x64,Windows 7 Professional,Windows 7 Professional x64,Windows 7 Starter,Windows 7 Starter x64,Windows 7 Ultimate,Windows 7 Ultimate x64,Windows 95,Windows 98,Windows ME,Windows Vista Business,Windows Vista Business x64,Windows Vista Enterprise,Windows Vista Enterprise x64,Windows Vista Home Basic,Windows Vista Home Basic x64,Windows Vista Home Premium,Windows Vista Home Premium x64,Windows Vista Ultimate,Windows Vista Ultimate x64,Windows XP Home,Windows XP Home x64,Windows XP Professional,Windows XP Professional x64 Multimedia Haut-parleurs intégrés Oui Appareil photo intégré Non Synthoniseur TV intégré Non Nombre de haut-parleurs 2 Puissance évaluée de RMS 4 W Design position de marché Professionnel Certifié Energy Star Oui Conformité EPEAT Silver Couleur du produit Noir Certification TCO, CE, TÜV-Bauart, VCCI-B, EAC Connectivité Nombre de ports VGA (D-Sub) 1 Port DVI Oui Entrée audio Oui Quantité de ports DVI-D 1 Quantité de ports HDMI 1 HDCP Oui Secteur d'entrée d'alimentation Oui Ergonomie Montage VESA Oui Port de câble antivol Oui Bouton marche/arrêt intégré Oui Réglage de la hauteur Non Norme VESA 100 x 100 mm Type d'emplacement de verrouillage de câble Kensington Pivot Non Pivotant Non Ajustement de l'inclinaison Oui Angle d'inclinaison -4 - 20° Affichage à l'écran (OSD) Oui Affichage multilingue à l'écran Chinois simplifié, Anglais, Espagnol, Français, Italien, Japonais, Portugais, Russe Nombre de langues OSD 9 Plug and Play Oui Client léger Thin client installé Non Gestion d'énergie Classe d'efficacité énergétique A Consommation annuelle d'énergie 32 kWh Consommation électrique typique 24 W Consommation d'énergie (mode veille) 0,5 W Tension d'entrée AC 100 - 240 V Fréquence d'entrée AC 50 - 60 Hz Conditions environnementales Température d'opération 5 - 35 °C Température hors fonctionnement -20 - 60 °C Taux d'humidité de fonctionnement 10 - 80% Taux d'humidité relative (stockage) 5 - 85% Poids et dimensions Largeur 532,5 mm Profondeur 44 mm Hauteur 317,5 mm Largeur appareil (support inclus) 532,5 mm Profondeur (support inclus) 180 mm Hauteur (support inclus) 387,5 mm Poids (avec support) 4 kg Informations sur l'emballage Stand inclus Oui Câbles inclus Secteur, Audio (3,5 mm), DVI Guide de démarrage rapide Oui Autres caractéristiques Écran LED