Ssb narrow

Vends SSB NARROW FILTER ICOM FL-223 (1, kHz) en parfait état de présentation et de fonctionnement. Filtre ICOM FL-223 (SSB étroit 1,9 kHz) compatible ICOM IC-706MK1 IC-706MKII IC-706MKIIG IC-703 IC-718 IC-756 IC-R75 IC-756 IC-775DSP IC-746 etc...

Filtre ICOM type FL-223 SSB  1,9KHz à -6dB, fréquence 9,0115MHz. Pour TX Icom Excellent état

Filtre ICOM type FL-222 SSB  1,8KHz à -6dB, fréquence 455KHz. Pour TX Icom Excellent état

Inrad #110 narrow SSB 2.1 kHz crystal filter for many Icom transceivers (9.011 MHz IF)   ENGLISH BELOW   =========   FRANCAIS ========= Il s'agit d'un filtre à quartz Inrad (International Radio) de haute qualité pour la fréquence intermédiaire typique 9.0115 MHz pour un grand nombre d'émetteurs-récepteurs Icom. Ce filtre est de type étroit avec une bande passante de 2100 Hz, ce qui permet d'obtenir une bonne sélectivité pour la réception des signaux BLU (SSB) sur des bandes encombrées, ainsi que pour certaines émissions digitales. Le filtre est entièrement fonctionnel, en très bon état. Je l’ai utilisé dans mon IC-746, mais je n’en ai plus besoin puisque j’utilise un autre émetteur-récepteur sans filtres. Ce filtre é tait vendu au prix de 118 USD sans taxes et livraison (site inrad.net), mais il n'est plus disponible et il est devenu un article très rare. Donc cette vente pourrait donc être considérée comme une bonne affaire. Vous achetez auprès d'un radioamateur licencié. Mon indicatif est F4VTS / SP9SOY. Livraison en Europe. L'endroit d'où j'expédie peut dépendre de la période car j'ai deux domiciles. Remise en mains propres possible à Nice uniquement après fixation d'un RV, Merci et 73!   ======== ENGLISH ======== This is a high quality Inrad (International Radio) quartz filter for the standard Icom I.F. of   9.0115 MHz for a large number of Icom transceivers and receivers. This filter is of the narrow type with a bandwidth of 2100 Hz, which provides good selectivity for the reception of SSB signals in our crowded bands, as well as for some digital emissions. The filter is fully functioning and in very good condition. I used it in my IC-746, but I don't need it anymore since I use now another transceiver that has no filter option. This filter was priced at 118 USD (inrad.net store) without duty fees and shipping, but it is no longer available and has become a very rare item. So this sale could be considered as a good deal. You are buying from a licensed radioamateur. My call is F4VTS / SP9SOY. Shipping to Europe. The place I ship from may depend on the period because I have two homes. I can ship outside Europe but you should contact me first in this case in order to check the shipping cost. Also local custom/import taxes may apply in your country, if outside European Union. Be aware of that.   Personnal collection possible in Nice, France, only after fixing a date, Thank you for bidding and best 73 !  

ICOM ICR-70 SUPERBE récepteur de qualité professionnelle Façade en aluminium Le système de réception Icom IC-R70 est un superhétérodyne à quadruple conversion couvrant 100 kHz à 30 MHz avec une résolution d'affichage de 100 Hz.  Les modes de réception comprennent AM, SSB, RTTY, CW et FM [avec option EX257]. (OPTION INCLUSE dans cette vente)  Les fonctionnalités avancées comprennent: le réglage de la bande passante,  l'encoche IF,  l'AGC réglable 3 niveaux de réglage,  deux VFO's,  la prise Scope, la sortie ligne,  le RIT,  le verrouillage du cadran,  la prise d'entrée du convertisseur,  le suppresseur de bruit réglable  et le préamplificateur intégré. lire les avis sur eham.net https://www.eham.net/reviews/view-product?id=2594 FILTRES FL32 CW étroit FL30 SSB FL-33 filtre AM Emballage d'origine Alimentation incorporée Paiement par virement de préférence ou éventuellement chèque (espèces sur place) Envoi soigné The  Icom IC-R70  receiver system is a quadruple conversion superheterodyne covering 100 kHz to 30 MHz with 100 Hz  display resolution.  Modes of reception  includes AM, SSB, RTTY, CW and FM [with EX257 option]. FM OPTION is include  Advanced features include:  Pass Band Tuning, IF notch, adjustable AGC, three tuning rates, dual VFOs, Scope Jack, Line Output, RIT, dial lock, converter input jack, adjustable noise blanker and built-in preamplifier. read reviews on eham.net https://www.eham.net/reviews/view-product?id=2594 FILTERS FL32 CW narrow FL30 SSB FL-33 AM filter ORIGINAL PACKAGING Integrated power supply Payment by transfer preferably or possibly check (cash on site) Careful shipping idem yaesu kenwood ts sommerkamp radioamateur transceiver ham radio cibi icom

Ts-440sat décamétrique kenwood  En très bel état Emballage d'origine Transceiver décamétrique révisé, superbe fonctionnement Options installées: FILTRE CW YK88CN, FILTRE SSB étroit YK88SN et boite d'accord automatique. Ouvert en fréquences toutes bandes y compris 11m, très bonne modulation Très bel état, à saisir Micro à main et cordon d'alimentation. Paiement chèque virement  NO PAYPAL PAYPAL NOT ACCEPTED Envoi rapide et très soigné Ts-440sat Beautiful conditions Original packaging Revised transceiver, superb operation Options included: CW FILTER YK88CN, narrow SSB YK88SN FILTER and automatic tuner. Open in all band frequencies Very nice condition, to be seized Hand microphone and power cord. Payment by bank transfer NO PAYPAL PAYPAL NOT ACCEPTED Sending fast and very neat

ESSAYÉ EN FM ET LW OK POUR LES AUTRES BANDES PAS D’ANTENNES APPROPRIÉES Année: 1976-1978? Catégorie: Récepteur de diffusion - ou passé tuner WW2 Semi-conducteurs (le compte est seulement pour des transistors) 34: Superhétérodyne, conversion double / triple; IF / IF 2000/455 kHz bandes onde Diffusion, grande longueur d'onde, morethan 2 x SW, plus FM ou UHF. détails Type de puissance et de tension Ligne / piles (tout type) / 110/220 Volt Haut-parleur aimant permanent (Dynamic Pdyn) Haut-parleur (à bobine mobile) / 4 de pouce de diamètre = 10,2 cm out Power 2 W (qualité inconnue) de Radiomuseum.org Modèle: RF-4800 LBS / DR-48 - Panasonic, Matsushita, matière divers matériaux forme Modèle de table, profil bas (grande taille). Dimensions (LHP) 480 x 200 x 355 mm / 18,9 x 7,9 x 14 pouces notes Couverture LW, BC (MW), SW 1600-30000 kHz, VHF (FM). Dessous de 3000 kHz seule conversion, au-dessus de 3000 kHz à double conversion. Compteur numérique uniquement pour les bandes 2 ondes courtes - 8. Vendu aux États - Unis en tant que RF-4800 celui ci contrairement au DR 48 ne couvre pas le pas LW). Poids net (2,2 lb = 1 kg) 8 kg / 17 lb 9,9 oz (17.621 lb) The Panasonic RF-4800 LBS has been sold in Europe as DR-48, it covers also the longwave band. The DR-48 is a quite bulky desktop receiver with it's dimensions of 48 x 20, x 35,5 cm and it's weight of 8 kg; two metal handles give protection to the front panel, when the set is turned face down - the give the set the aspect of a semiprofessional receiver. The RF-4800 can be powered from 110 / 220 V mains, from a 12 V car battery or eight UM-1 / mono cells accomodated in two battery compartments. At the left side of the frontpanel, You find the big speaker and below the mains switch, the jacks for an external speaker and a cassette recorder at further right the rotary controls for volume, bass, treble and the BFO pitch control. In the middle of the display window at the right, You find the red LED display of the frequency counter active on shortwave bands SW 2 - 7 and the auxiliary dials for long-, mediumwaves, tropical bands (SW 1) and the FM broadcast band at the left and the shortwave bands SW 2 - 7, each 4 MHz wide, at the right. In the middle of the frontpanel the huge main tuning knob is located, it is equipped with a crank and can be set to slow and fast tuning speed by pressing the knob in the centre - this knob will tune the shortwave bands. The frequency display is active on these band segments and the receiver operates as a double conversion receiver. The second smaller tuning knob tunes the long-, mediumwave, SW1 and FM broadcast bands, in these bands, the set operates as single conversion set and the frequency display is not active. The signal strength meter tends to read high, in the RF-4800 it has a white background, this is a possibility to distinguish the set from the RF-4900, the S meter of the successor comes with a black background. Below You find a row of switches: the switch to activate the AFC in FM mode selects between the two AM bandwidths in AM mode, the middle switch activates the noise limiter and the third one the BFO: use the BFO pitch control just below for an optimum BFO note when receiving CW transmissions and for optimum speech reproduction in SSB mode - voices should no sound like mickey mouse. The bandswitch for LW - MW - SW1 - FM and the band segment switch for SW 2 - 7 are located below the right auxilitary frequency dial. The frequency counter can be calibrated from a 5 or 10 MHz time signal and frequency standard transmission from WWV / WWVH or even from another station transmitting exactly on a known frequency. Tune in to "Radio Deutsche" Welle on 6075 kHz and wait for news and station identification, then tune to maximum S meter reading and use the SW 2-7 CAL control to set the frequency display exactly to display 6.075 - with this control not set correctly, the frequency displayed can be 2 - 4 kHz off the actual frequency. Keep in mind, the RF-4800 is no PLL synthesized set. In the right lower part of the front panel, You find the ANT TRIM to match an external antenna, the R.F. gain control. This should be set to maximum position or "DX" as a standard, in case of overloading of the receiver front end due to high signal level conditions in acrowded shortwave broadcast band wit ha long antenna, You can reduce the R.F. gain. In fact, this knob acts more like an attenuator as there is no switch to turn off the AGC (automated gain control) completely. Three more switches activate dial illumination, frequency display and set the S meter to indicate battery power. At the rear face of the DR-48 / RF-4800 LBS, You find the two folding out ferrite antennas for long- and mediumwaves, the international variant comes with only one ferrite antenna. Next to the antenna sockets, there is a PL / SO 239 antenna socket for SW 2 - 7. The DIN socket can be used to feed the DR-48's audio signal to a cassette recorder and also to feed a signal from an external audio source to the receiver, set the switch at the rear to "PHONO" to use the DR-48 as audio amplifier. The operation scheme of the DR-48 is quite straightforward: turn on the set, make sure the RF gain control is turned to the MAX setting, the AM bandwidth to wide and the BFO turned off. The right bandselector should be on SW 2 - 7 and the left on "2" to select the 3 - 7 MHz range, the use the big tuning knob to find the "Deutsche Welle" from Cologne on 6.075 MHz. If the signal peak is one or two kHz higher or lower then 6.075, use the SW 2-7 CAL to adjust the frequency display setting to the correct frequency. Due to it's conventional design as a double conversion receiver with a quite low first I.F. and a frequency counter, the receiver shows a certain frequency drift even after warm up, CW or radioteletype decoding with an automatic decoder and even reception of SSB signals need slight retuning of the set from time to time, automated recordings won't work properly. The skirt selectivity of the two I.F. filter's is mediocre. quite often, You hear an 5 kHz interference whistle from a adjacent channel carrier. As the receiver operates as single conversion set below 3 MHz, You might encounter mirroring or "ghost signals" appearing 900 kHz from the original signal away. As the internal ferrite antennas cannot be switched of, the DR-48 / RF-4800 is not well suited as a longwave / mediumwave DX receiver. Conclusion: the DR-48 / RF-4800 represents the state of the art from the early eighties as desktop receiver with double conversion circuitry connected to a frequency counter, stability, suppression on unwanted signals and selectivity of the I.F. filters is all below the expectations for a shortwave receiver in the 21st century. The DR-48 / RF-4800 looks very impressive and makes a decent secondary or entry level shortwave radio, for real Dxing, You would need a set with better filters, maybe a notch filter and passband tuning and a few memories to compare different frequencies. If You find a DR-48 / RF-4800 for a bargain price, get one, and You might have lot of fun with it. The technical built quality is not superior, so You might encounter some work until the receiver is running properly. In my sets, the wave band and shortwave band switches all did contact poorly and needed cleaning, as well as the AM narrow / wide switch and even the rotary volume and tone controls.

ulsionnels) •Atténuateur 20 dB Récepteur AOR - AR 8200Mk3 Réception sans trou de 500Khz à 3Ghz  Vendu avec Accessoires + Notice en Français Etat comme neuf - Très très peu servi !   Caractéristiques: Le récepteur/scanner portable AOR AR8200 Mark III dispose d’une plage de fréquence inégalée de 500 kHz à 3 GHz. Une grande amélioration de l’étage RF permet une stabilité en fréquence particulièrement performante ainsi qu’une grande sensibilité toute en améliorant la résistance aux produits d’inter-modulations et les ratios signal-bruit. Caractéristiques: Nouveau TCXO pour une meilleure stabilité - Performances inexistantes sur la plupart des récepteurs de tables ! Couverture de 500 kHz à 3 GHz - C’est le seul portatif du marché à avoir cette page de fréquence. Batteries Ni-MH fournis (1500 mAH). 1000 canaux mémoires (20 banques de 50 canaux). 40 banques de recherche. 2 VFO. Labellisation alphanumérique des mémoires. Contrôle et programmation par ordinateur (nécessite un câble en option). Récepteur tous modes incluant les modes FM « super narrow », AM large ou étroit en plus des modes standards USB, LSB et AM / FM. Véritable démodulateur USB et LSB. Inclut un filtre SSB de 3 kHz ! Antenne détachable sur support BNC avec masse négative. Emplacement interne pour cartes additionnelles en option permettant d’étendre les possibilités du Mark III: jusqu’à 4000 mémoires avec CTCSS, Squelch, recherche, éliminateur de tonalité, enregistreur audio (sauvegarde jusqu’à 20 secondes). Pas programmable par multiples de 50 Hz dans tous les modes. Supporte le pas aéronautique de 8,33 kHz. Limiteur de bruit et atténuateur. Analyseur d’activité « bande scope » avec possibilité de sauvegarde de l’activité. Quatre touches de fonction sur le côté permettent le fonctionnement d’une seule main. Afficheur large et multifonctions, clavier rétro illuminé. Économiseur de batterie avec indicateur de batterie déchargée. Fonctionnement possible avec une alimentation 12 Volts continue externe. Large choix d’accessoires. Contenu du coffret AR8200 Mark III: des accus NiMH 1500 mAh un chargeur secteur 220V un cordon allume-cigare une antenne télescopique une antenne cadre AM compacte un clip ceinture une dragonne ***************** Le récepteur Aor sera bien protégé pour le transport Expédition en Colissimo Suivi   N'hésitez pas à visiter notre boutique !  

SPECIFICATIONS GENERAL Type: HF (VHF) receiver Frequency range: 0.17-30 MHz in 6 bands (87.5-108 MHz option (76-90 MHz in Japan)) A: 0.17-0.41 MHz B: 0.525-1.25 MHz C: 1.25-3 MHz D: 3-7.5 MHz E: 7.5-18 MHz F: 18-30 MHz (Band spread on ham bands and major BC bands) Tuning steps: Continuous Mode: AM/SSB/CW (WFM option) Channels/memory management: No Power supply: Mains: 100 / 117 / 220 / 240 VAC External DC: 12-15 VDC Batteries: 8*R20/D Current drain/power consumption: ? mA Antenna impedance/connector: 50 ohms / SO-239 Hi-Z / Screw terminals Built-in telescopic whip Dimensions (W*H*D): 362*163*322 mm (14.25*6.42*12.68"), without options Weight: 7.3 Kg (16.1 lbs), without options Other features: RECEIVER SECTION Receiver system: Single conversion superheterodyne (Band A-E) IF: 455 KHz (WFM option: 10.7 MHz) Double conversion superheterodyne (Band F) 1st IF: 4.034 MHz 2nd IF: 455 KHz Sensitivity: Selectivity: AM narrow: 3 KHz (-6 dB), 15 KHz (-60 dB) AM wide: 5 KHz (-6 dB), 15 KHz (-50 dB) WFM (option): 150 KHz (-6 dB), 750 KHz (-50 dB) Image rejection: 50-70 dB depending on band AF output power/speaker: 1.5 W at 10% distortion / 8 ohms ! RETOUR REFUSER / NO RETURN !

Hi I just purchased an FT-891 and the IC-706MKIIG is no longer needed The '706 works fine and I have had many /M QSO's with it including /M to /M contact MA to WI last week. Comes with narrow SSB filter installed and the ICOM separation cable,  DC power cable  and  HM-103 microphone I usually used it with a Yaesu ATAS120 screwdriver antenna and I'm including the MFJ 1925 screwdriver controller and Comet CF-706 duplexer with it Great bargain if you're looking for a good mobile rig!