Unknown board probably

Here I am selling a Yaesu FT-707 wreck, not working, for spare parts or other use. This includes:          Front panel with Perspex display window, potentiometers, rotary switches, push buttons and power switch (all switches and potentiometers work smoothly, the face plate in nice condition)          Case (fair condition, look at photos) and chassis.         100W PA module with band filters and fan. The PA transistors are not short-circuited or burnt out, probably working condition.          AF board with band crystals and BFO circuit (working-pull condition)          Regulator board (working-pull condition)   Look at my others auctions, I sell the complete VFO assembly with knob too.   Relatively low shipment fee by post with tracking (30 eur). Weight 6 kg.   Custom duties may apply if shipped outside Europe. Place where I will ship from can vary, because I have two homes.  

Miniwhip Active Antenna MC LF VlF Mini Whip Shortwave SDR RX Portable Recei M ZH Description: MINIWHIP VLF LF HF ACTIVE ANTENNA.This is known PA0NHC newest design of MiniWhip Antenna. I have redesigned and built it on SMD components but the circuit diagram itself stayed the same as it had been described on his web page in open source. This sale includes the MiniWhip and Power Splitter assembled and tested boards. They go with its circuit diagrams and part list specification. No cables or connectors are included. This new version of PA0NHC MiniWhip Antenna has these features.New version, using modern BF998 and BCX54 semi conductors.Real class A circuitry, clean reception without IMD.One coax connection.Broadband R/C coupling to the receiver, no transformer For best signal-to-noise ratio:install the Miniwhip onto a well grounded mast.connect "GND" of the Miniwhip PCB to that mast.place HI-Ui ferrite cores (Ui bwtween 5000 and 10.000) on the beginning and end of all cables to block cable noise currents. Specifications: Frequency range: 10 KHz - 30 MHz Power: 12 - 15 volts at 150 mA Second order output intercept point: Greater than + 70 dBm Third order output intercept point: Greater than + 30 dBm Maximum output power: in excess of - 15 dBm PCB Size: Length (mm): As the picture show Connector: BNC Feed line: 50 - 100 ohm coaxial cable up to 100 meter long T o note please: Each antenna performs as good as its installation permits it to. Any active antenna is not working good inside the house! It should be mounted OUTSIDE and as high as possible. Place this MiniWhip antenna PCB inside suitable enclosure of your choise and mount outside the house. Probably for the enclosure you can use a piece of the PVC tube which available in varios diameters in a local store. Do not use metal enclosure! It wont work there! For max. sensitivity: this antenna should be positioned as high and free from meta Package include: 1Set Board Note:   The color might be a little different from the actual product due to color display of different monitors.  Please allow 1-3 cm error. Le 06-févr.-20 à 21:45:18 Paris, le vendeur a ajouté les informations suivantes:

Description: MINIWHIP VLF LF HF ACTIVE ANTENNA.This is known PA0NHC newest design of MiniWhip Antenna. I have redesigned and built it on SMD components but the circuit diagram itself stayed the same as it had been described on his web page in open source. This sale includes the MiniWhip and Power Splitter assembled and tested boards. They go with its circuit diagrams and part list specification. No cables or connectors are included. This new version of PA0NHC MiniWhip Antenna has these features.New version, using modern BF998 and BCX54 semi conductors.Real class A circuitry, clean reception without IMD.One coax connection.Broadband R/C coupling to the receiver, no transformer For best signal-to-noise ratio:install the Miniwhip onto a well grounded mast.connect "GND" of the Miniwhip PCB to that mast.place HI-Ui ferrite cores (Ui bwtween 5000 and 10.000) on the beginning and end of all cables to block cable noise currents. Specifications: Frequency range: 10 KHz - 30 MHz Power: 12 - 15 volts at 150 mA Second order output intercept point: Greater than + 70 dBm Third order output intercept point: Greater than + 30 dBm Maximum output power: in excess of - 15 dBm PCB Size: Length (mm): As the picture show Connector: BNC Feed line: 50 - 100 ohm coaxial cable up to 100 meter long T o note please: Each antenna performs as good as its installation permits it to. Any active antenna is not working good inside the house! It should be mounted OUTSIDE and as high as possible. Place this MiniWhip antenna PCB inside suitable enclosure of your choise and mount outside the house. Probably for the enclosure you can use a piece of the PVC tube which available in varios diameters in a local store. Do not use metal enclosure! It wont work there! For max. sensitivity: this antenna should be positioned as high and free from meta Package include: 1Set Board Note:   The color might be a little different from the actual product due to color display of different monitors.  Please allow 1-3 cm error. Le 11-mars-20 à 13:30:27 Paris, le vendeur a ajouté les informations suivantes:

Description: MINIWHIP VLF LF HF ACTIVE ANTENNA.This is known PA0NHC newest design of MiniWhip Antenna. I have redesigned and built it on SMD components but the circuit diagram itself stayed the same as it had been described on his web page in open source. This sale includes the MiniWhip and Power Splitter assembled and tested boards. They go with its circuit diagrams and part list specification. No cables or connectors are included. This new version of PA0NHC MiniWhip Antenna has these features.New version, using modern BF998 and BCX54 semi conductors.Real class A circuitry, clean reception without IMD.One coax connection.Broadband R/C coupling to the receiver, no transformer For best signal-to-noise ratio:install the Miniwhip onto a well grounded mast.connect "GND" of the Miniwhip PCB to that mast.place HI-Ui ferrite cores (Ui bwtween 5000 and 10.000) on the beginning and end of all cables to block cable noise currents. Specifications: Frequency range: 10 KHz - 30 MHz Power: 12 - 15 volts at 150 mA Second order output intercept point: Greater than + 70 dBm Third order output intercept point: Greater than + 30 dBm Maximum output power: in excess of - 15 dBm PCB Size: Length (mm): As the picture show Connector: BNC Feed line: 50 - 100 ohm coaxial cable up to 100 meter long T o note please: Each antenna performs as good as its installation permits it to. Any active antenna is not working good inside the house! It should be mounted OUTSIDE and as high as possible. Place this MiniWhip antenna PCB inside suitable enclosure of your choise and mount outside the house. Probably for the enclosure you can use a piece of the PVC tube which available in varios diameters in a local store. Do not use metal enclosure! It wont work there! For max. sensitivity: this antenna should be positioned as high and free from meta Package include: 1Set Board Note:   The color might be a little different from the actual product due to color display of different monitors.  Please allow 1-3 cm error. Le 04-avr.-20 à 15:50:26 Paris, le vendeur a ajouté les informations suivantes: