Fm broadcast

1000W DSP + PLL STEREO FM Broadcast Transmitter. État : "Pour pièces détachées/ne fonctionne pas" Technical Specification   - RF Output Power: 0 to 1000 Watt ±10%, 1W/Step - Frequency range: 87.5-108 Mhz, 5Khz/Step - AC power source: AC110V~240V,50-60Hz, single phase - Frequency Stability: better than ±100Hz - S/N Ratio: More than 60dB - Distortion: less than 0.1% - Modulation: FM,±75KHz peak deviation - Transmission Signal: FM Stereo or Mono - Tuning Design: Stable PLL Technology - Harmonic suppression: <    -75dBC - Stereo Separation: More than 50db - RF Output Connector: N Type (L16) -female - RF Output Impedance: 50 ohm - Audio channel Frequency Response: 50 - 15000Hz ±0.5dB - Audio Input Level: -15db, Max -30db - Audio Input Connector: RCA type - AUX Input Connector: none - Operating temperature range: -10 to 45 ℃ - Size of Transmitter Unit: 483mm * 400mm * 88mm (19" Standard 2U case) - Shipping Weight: 11.5Kg bonjour le circuit RF a changé  le site pour le réparer merci il a la photo du circuit RF http://www.warner-rf.com plus d infos au 06.95.04.61.34

Emetteur FM Broadcast Professional TEM 100W- 300W FM Transmitter 88-108 Mhz. État : "Occasion" -Pilote Emetteur TEM 7A 960-2 (Exciter) 20W pré-réglable par cavalier 6w-12w-20w puis par potentiomètre. -Entrée MPX seulement, pas d'entrée BF. -Entrée RDS -Réglage puissance -Réglage Excursion MPX -Amplificateur RF TEM 7P30DH20T (Amplifier) 300W mais réglé sur 100W. Non testé sur 300w, monte à 150W Max ! Transistor de puissance: BLF278

Emetteur FM Broadcast Professional ECRESO 20W FM Transmitter 88-108 Mhz. État : "Occasion" En très bon état de fonctionnement. Entrées Signal MPX, BF droite et gauche, mono. Entrée Auxiliaire RDS Puissance HF réglable 0-20W Réglage Excursion MPX, BF Mono et stéréo. Réglage Fréquence d'émission par Switch. Notice fournie

SCOOPY   AETA  AUDIO Reportage en direct  par telephone lignes NUMERIS  avec 5AS lignes ANALOGIQUES 2 Eentrees micro lignes  XLR  / FILTRES  / Limiteur compresseur 2 Prises casques  individuelles   volume en face Alimentation  12V   /  compartiment batteries rechargeables

Technical Specification   - RF Output Power: 0 to 1000 Watt ±10%, 1W/Step - Frequency range: 87.5-108 Mhz, 5Khz/Step - AC power source: AC110V~240V,50-60Hz, single phase - Frequency Stability: better than ±100Hz - S/N Ratio: More than 60dB - Distortion: less than 0.1% - Modulation: FM,±75KHz peak deviation - Transmission Signal: FM Stereo or Mono - Tuning Design: Stable PLL Technology - Harmonic suppression: <      -75dBC - Stereo Separation: More than 50db - RF Output Connector: N Type (L16) -female - RF Output Impedance: 50 ohm - Audio channel Frequency Response: 50 - 15000Hz ±0.5dB - Audio Input Level: -15db, Max -30db - Audio Input Connector: RCA type - AUX Input Connector: none - Operating temperature range: -10 to 45 ℃ - Size of Transmitter Unit: 483mm * 400mm * 88mm (19" Standard 2U case) - Shipping Weight: 11.5Kg bonjour le circuit RF a changé  le site pour le réparer merci il a la photo du circuit RF http://www.warner-rf.com/

LIKE NEW !   A COMPLETE FM Broadcast STATION 88-108Mhz : with FM 30 watts Pilot exciter, with RDS encoder, with Stereo coder, with FM 4 bands audio processor, with 2x Broadband antennas + 2 ways splitter: - BW DSPX = 880 €uros - AZTEC AUDEMAT FMB10 = 170 €uros - RVR PTX30UHT = 340 €uros - 2x Antennas = 290 €uros - Splitter 2 ways = 140 €uros Total initial price = 1820 euros ******************************************************************************************************************************** ALL NEW Never used !  - STEREO CODER and FM audio processor: BW - DSPX (it's not the '' mini '' version) But the great DSPX broadcast processor for FM - Dj's - Mastering...   (I pay this apparatus: 1800 €uros with all taxes) ALL new, never used, with technical notice, software and pdf (free) on the BW compagny site:  for the notice: http://a-bc.co.uk/Misc/Tools/DSPX-FM%20v320%20Manual.pdf Processeur audio FM traitement de son numérique multibandes 4 bandes ==>   https://www.youtube.com/watch?v=oLPv2J8_X1o     or     https://www.youtube.com/watch?v=5IFjZmZlzWo - 4 bandes AGC - limiteur 4 bandes - Clippeur 3 bandes - Connectivité LAN - Stereo Coder (50us or 75 us) - Output MPX 19Khz - Input RDS (with sync pilot) - sortie droite-gauche avec clippeur indépendant - Ethernet RJ45... Like NEW - Just revised and calibrated for 330 €uros by ''AUDEMAT-Bordeaux(France)'' - RDS Encoder: Aztec FMB10/40  Configuration wizard Simulated PS and Radiotext display Dynamic PS data from automation Labeling Command interpreter 19 kHz Synchronization - External, Internal or Automatic Synchronization monitoring Software control of RDS injection level – no trimpots Software adjustment of 57 kHz Phase ASCII Commands to enable or disable the RDS SCA Composite bypass feature in case of failure Superb spectral purity of the RDS signal Like NEW - Because used only 6 months in ''help mode'' - FM 88-108 MHz PLL Exciter transmitter - 0 to 30 watts: RVR - PTX30UHT Like NEW - 2x Broadband antennas for 1kW maxi (Mat Equipment) + 1,2 Kw Splitter 2 ways N/N ------------------------------------------------------------------------------------------------------------------------------ ------------------------------------------------------------------------------------------------------------------------------ NO DISPUTE - MY EVALUATION FEEDBACK IS MY GUARANTEE France: Paiement par virement uniquement, transport en plusieurs colis. International seller: NO PAYPAL (for no big service taxes) ==>  ONLY: money transfer bank to bank  with IBAN/BIC contact me for the right transport charges, with your country. It's heavy !  transport in 3 solids cardboards.

LIKE NEW !   A COMPLETE FM Broadcast STATION 88-108Mhz : with FM 30 watts Pilot exciter, with 2x Broadband antennas + 2 ways splitter: - RVR PTX30UHT = 400 €uros - 2x Antennas = 350 €uros - Splitter 2 ways = 170 €uros Total initial price = 920 euros ******************************************************************************************************************************** Like NEW - Because used only 6 months in ''help mode'' - FM 88-108 MHz PLL Exciter transmitter - 0 to 30 watts: RVR - PTX30UHT + Like NEW - 2x Broadband antennas for 1kW maxi (Mat Equipment) + 1,2 Kw Splitter 2 ways N/N ------------------------------------------------------------------------------------------------------------------------------ ------------------------------------------------------------------------------------------------------------------------------ NO DISPUTE - MY EVALUATION FEEDBACK IS MY GUARANTEE France: Paiement par virement uniquement, transport en plusieurs colis. International seller: NO PAYPAL (for no big service taxes) ==>  ONLY: money transfer bank to bank  with IBAN/BIC contact me for the right transport charges, with your country. It's heavy !  transport in 2 solids cardboards.

No sales if the buyer profile has less than 12 positive reviews PROFIL ACHETEUR avec moins de 12 évaluations positives, votre achat sera rejeté For a FM Broadcast Station... Good cosmetic, good condition... 2x Broadband Antennas - Folded Dipole (88-108 Mhz) - Gain 5.3 dB - without tune - réf. Mat Equipment (800 watts - N connector) = 208 €uros (2x 104 €uros) 1x Splitter 2 ways- N / N connectors = 140 €uros Total initial price = 348 euros ******************************************************************************************************************************** NO DISPUTE - MY EVALUATION FEEDBACK IS MY GUARANTEE France: Paiement par chèque, transport soigné. International seller: PAYPAL  ==> PRE-SALE: contact me for the right transport charges, with your country

Broadcast FM Band Stop Filter (88 - 108 MHz FM Trap) WLFR Includes  1x RTL-SDR Blog Broadcast FM Band-Stop Filter 1x SMA male to SMA male adapter Blocks the broadcast FM band between 88 – 108 MHz with over 50dB of attenuation.  Designed for maximum attenuation between 88 - 108 MHz and the 3dB roll off points are at 76 MHz and 122 MHz. Insertion loss is less than 0.5 dB between 0 – 1 GHz, and mostly less than 1.5 dB between 1 – 3 GHz.  Uses SMA female connectors. Comes with a free SMA male to SMA male adapter. A broadcast FM block filter can help if you have very strong broadcasts in your area that are overloading the SDR dongle. Also known as “FM Trap”. Notes: RX filter only. Designed for SDR users, but might also be useful for TV users struggling with FM interference. But TV users please carefully check the spectrum analyzer graphs and 3dB roll off points to ensure that it will not block a TV signal of interest. e.g. Channels between 76 - 88 MHz could be attenuated enough to lose reception. Le 16-juil.-19 à 17:26:15 Paris, le vendeur a ajouté les informations suivantes:

Broadcast Transmitter 1000W DSP PLL STEREO FM. État : "Neuf" Service de livraison : Livraison en Relais Mondial Relay Technical Specification    -  RF Output Power: 0 to 1000 Watt ±10% , 1W/Step  - Frequency range: 87.5-108 Mhz, 5Khz/Step - AC power source: AC110V~240V,50-60Hz, single phase - Frequency Stability: better than ±100Hz - S/N Ratio: More than 60dB - Distortion: less than 0.1% - Modulation: FM,±75KHz peak deviation - Transmission Signal: FM Stereo or Mono - Tuning Design: Stable PLL Technology - Harmonic suppression: - Stereo Separation: More than 50db - RF Output Connector: N Type (L16) -female - RF Output Impedance: 50 ohm - Audio channel Frequency Response: 50 - 15000Hz ±0.5dB - Audio Input Level: -15db, Max -30db - Audio Input Connector: RCA type - AUX Input Connector: none - Operating temperature range: -10 to 45 ℃ - Size of Transmitter Unit: 483mm * 400mm * 88mm (19" Standard 2U case)

Broadcast Transmitter 1000W DSP PLL STEREO FM [FMT3.0-1000]. État : "Occasion" Technical Specification   - RF Output Power: 0 to 1000 Watt ±10%, 1W/Step - Frequency range: 87.5-108 Mhz, 5Khz/Step - AC power source: AC110V~240V,50-60Hz, single phase - Frequency Stability: better than ±100Hz - S/N Ratio: More than 60dB - Distortion: less than 0.1% - Modulation: FM,±75KHz peak deviation - Transmission Signal: FM Stereo or Mono - Tuning Design: Stable PLL Technology - Harmonic suppression: <   -75dBC - Stereo Separation: More than 50db - RF Output Connector: N Type (L16) -female - RF Output Impedance: 50 ohm - Audio channel Frequency Response: 50 - 15000Hz ±0.5dB - Audio Input Level: -15db, Max -30db - Audio Input Connector: RCA type - AUX Input Connector: none - Operating temperature range: -10 to 45 ℃ - Size of Transmitter Unit: 483mm * 400mm * 88mm (19" Standard 2U case) - Shipping Weight: 11.5Kg

Broadcast Transmitter 1000W DSP PLL STEREO FM. État : "Pour pièces détachées/ne fonctionne pas" Technical Specification   - RF Output Power: 0 to 1000 Watt ±10%, 1W/Step - Frequency range: 87.5-108 Mhz, 5Khz/Step - AC power source: AC110V~240V,50-60Hz, single phase - Frequency Stability: better than ±100Hz - S/N Ratio: More than 60dB - Distortion: less than 0.1% - Modulation: FM,±75KHz peak deviation - Transmission Signal: FM Stereo or Mono - Tuning Design: Stable PLL Technology - Harmonic suppression: <   -75dBC - Stereo Separation: More than 50db - RF Output Connector: N Type (L16) -female - RF Output Impedance: 50 ohm - Audio channel Frequency Response: 50 - 15000Hz ±0.5dB - Audio Input Level: -15db, Max -30db - Audio Input Connector: RCA type - AUX Input Connector: none - Operating temperature range: -10 to 45 ℃ - Size of Transmitter Unit: 483mm * 400mm * 88mm (19" Standard 2U case) - Shipping Weight: 11.5Kg bonjour le circuit RF a changé  le site pour le réparer merci il a la photo du circuit RF http://www.warner-rf.com/

Broadcast radio FM A vendre émetteur FM de 40 watts de marque ELENOS. Réglable de 2 à 40 Watts. Entrée composite pour codeur RDS et/ou Stéréo. Top qualité c'est du Pro made in iltaly. En parfait état de fonctionnement, révisé et dispo de suite. Documentation complète.

Broadcast radio FM A vendre émetteur FM pilote de 40 watts de marque ELENOS. Réglable de 2 à 40 Watts. Entrée composite pour codeur RDS et/ou Stéréo. Top qualité c'est du Pro made in iltaly. En parfait état de fonctionnement et révisé. Documentation complète.

BROADCAST FM 88 108MHZ MARQUE QUARK REFERENCE FALCON 50 PUISSANCE 30W AUDIO MONO XLR ENTREE MPX BNC ENTREE SCA BNC UTILISATION UNIQUEMENT EN ATELIER POUR ESSAI TRAITEMENT DE SONO VENDU COMME SUR LE PHOTO

Includes  1x RTL-SDR Blog Broadcast FM Band-Stop Filter 1x SMA male to SMA male adapter Blocks the broadcast FM band between 88 – 108 MHz with over 50dB of attenuation.  Designed for maximum attenuation between 88 - 108 MHz and the 3dB roll off points are at 76 MHz and 122 MHz. Insertion loss is less than 0.5 dB between 0 – 1 GHz, and mostly less than 1.5 dB between 1 – 3 GHz.  Uses SMA female connectors. Comes with a free SMA male to SMA male adapter. A broadcast FM block filter can help if you have very strong broadcasts in your area that are overloading the SDR dongle. Also known as “FM Trap”. Notes: RX filter only. Designed for SDR users, but might also be useful for TV users struggling with FM interference. But TV users please carefully check the spectrum analyzer graphs and 3dB roll off points to ensure that it will not block a TV signal of interest. e.g. Channels between 76 - 88 MHz could be attenuated enough to lose reception.   Includes  1x RTL-SDR Blog Broadcast FM Band-Stop Filter 1x SMA male to SMA male adapter Blocks the broadcast FM band between 88 – 108 MHz with over 50dB of attenuation.  Designed for maximum attenuation between 88 - 108 MHz and the 3dB roll off points are at 76 MHz and 122 MHz. Insertion loss is less than 0.5 dB between 0 – 1 GHz, and mostly less than 1.5 dB between 1 – 3 GHz.  Uses SMA female connectors. Comes with a free SMA male to SMA male adapter. A broadcast FM block filter can help if you have very strong broadcasts in your area that are overloading the SDR dongle. Also known as “FM Trap”. Notes: RX filter only. Designed for SDR users, but might also be useful for TV users struggling with FM interference. But TV users please carefully check the spectrum analyzer graphs and 3dB roll off points to ensure that it will not block a TV signal of interest. e.g. Channels between 76 - 88 MHz could be attenuated enough to lose reception. Le 26-août-19 à 20:34:53 Paris, le vendeur a ajouté les informations suivantes:

Includes  1x RTL-SDR Blog Broadcast FM Band-Stop Filter 1x SMA male to SMA male adapter Blocks the broadcast FM band between 88 – 108 MHz with over 50dB of attenuation.  Designed for maximum attenuation between 88 - 108 MHz and the 3dB roll off points are at 76 MHz and 122 MHz. Insertion loss is less than 0.5 dB between 0 – 1 GHz, and mostly less than 1.5 dB between 1 – 3 GHz.  Uses SMA female connectors. Comes with a free SMA male to SMA male adapter. A broadcast FM block filter can help if you have very strong broadcasts in your area that are overloading the SDR dongle. Also known as “FM Trap”. Notes: RX filter only. Designed for SDR users, but might also be useful for TV users struggling with FM interference. But TV users please carefully check the spectrum analyzer graphs and 3dB roll off points to ensure that it will not block a TV signal of interest. e.g. Channels between 76 - 88 MHz could be attenuated enough to lose reception.   Le 22-mai-19 à 08:54:20 Paris, le vendeur a ajouté les informations suivantes:

Includes  1x RTL-SDR Blog Broadcast FM Band-Stop Filter 1x SMA male to SMA male adapter Blocks the broadcast FM band between 88 – 108 MHz with over 50dB of attenuation.  Designed for maximum attenuation between 88 - 108 MHz and the 3dB roll off points are at 76 MHz and 122 MHz. Insertion loss is less than 0.5 dB between 0 – 1 GHz, and mostly less than 1.5 dB between 1 – 3 GHz.  Uses SMA female connectors. Comes with a free SMA male to SMA male adapter. A broadcast FM block filter can help if you have very strong broadcasts in your area that are overloading the SDR dongle. Also known as “FM Trap”. Notes: RX filter only. Designed for SDR users, but might also be useful for TV users struggling with FM interference. But TV users please carefully check the spectrum analyzer graphs and 3dB roll off points to ensure that it will not block a TV signal of interest. e.g. Channels between 76 - 88 MHz could be attenuated enough to lose reception. Le 04-juil.-19 à 14:50:06 Paris, le vendeur a ajouté les informations suivantes:

Includes  1x RTL-SDR Blog Broadcast FM Band-Stop Filter 1x SMA male to SMA male adapter Blocks the broadcast FM band between 88 – 108 MHz with over 50dB of attenuation.  Designed for maximum attenuation between 88 - 108 MHz and the 3dB roll off points are at 76 MHz and 122 MHz. Insertion loss is less than 0.5 dB between 0 – 1 GHz, and mostly less than 1.5 dB between 1 – 3 GHz.  Uses SMA female connectors. Comes with a free SMA male to SMA male adapter. A broadcast FM block filter can help if you have very strong broadcasts in your area that are overloading the SDR dongle. Also known as “FM Trap”. Notes: RX filter only. Designed for SDR users, but might also be useful for TV users struggling with FM interference. But TV users please carefully check the spectrum analyzer graphs and 3dB roll off points to ensure that it will not block a TV signal of interest. e.g. Channels between 76 - 88 MHz could be attenuated enough to lose reception. Le 13-juil.-19 à 11:10:30 Paris, le vendeur a ajouté les informations suivantes:

Includes  1x RTL-SDR Blog Broadcast FM Band-Stop Filter 1x SMA male to SMA male adapter Blocks the broadcast FM band between 88 – 108 MHz with over 50dB of attenuation.  Designed for maximum attenuation between 88 - 108 MHz and the 3dB roll off points are at 76 MHz and 122 MHz. Insertion loss is less than 0.5 dB between 0 – 1 GHz, and mostly less than 1.5 dB between 1 – 3 GHz.  Uses SMA female connectors. Comes with a free SMA male to SMA male adapter. A broadcast FM block filter can help if you have very strong broadcasts in your area that are overloading the SDR dongle. Also known as “FM Trap”. Notes: RX filter only. Designed for SDR users, but might also be useful for TV users struggling with FM interference. But TV users please carefully check the spectrum analyzer graphs and 3dB roll off points to ensure that it will not block a TV signal of interest. e.g. Channels between 76 - 88 MHz could be attenuated enough to lose reception. Le 17-sept.-19 à 16:27:16 Paris, le vendeur a ajouté les informations suivantes:

émetteur broadcast professionnel FM (88 à 108mhz) de 20W (d'apres ce que ma dit le technicien il est modifiable pour la bande 144mhz, mais ne me demandez pas comment je ne sais pas !) fonctionne parfaitement (valeur neuf actuel 870€)

no sales if the buyer profile has less than 12 positive reviews PROFIL ACHETEUR avec moins de 12 évaluations positives, votre achat sera rejeté Like NEW - Because used only 8 months in ''help mode'' - FM 88-108 MHz PLL Exciter transmitter - 0 to 30 watts: RVR - PTX30UHT ------------------------------------------------------------------------------------------------------------------------------ NO DISPUTE - MY EVALUATION FEEDBACK IS MY GUARANTEE France: Paiement par chèque, transport colissimo contre signature. International seller: NO PAYPAL (for no big service taxes) ==>  ONLY: money transfer bank to bank  with IBAN/BIC contact me for the right transport charges, with your country. It's heavy !  transport in 3 solids cardboards. ==> PRE-SALE: contact me for the right transport charges, with your country

Technical Specification   - RF Output Power: 0 to 1000 Watt ±10%, 1W/Step - Frequency range: 87.5-108 Mhz, 5Khz/Step - AC power source: AC110V~240V,50-60Hz, single phase - Frequency Stability: better than ±100Hz - S/N Ratio: More than 60dB - Distortion: less than 0.1% - Modulation: FM,±75KHz peak deviation - Transmission Signal: FM Stereo or Mono - Tuning Design: Stable PLL Technology - Harmonic suppression: <   -75dBC - Stereo Separation: More than 50db - RF Output Connector: N Type (L16) -female - RF Output Impedance: 50 ohm - Audio channel Frequency Response: 50 - 15000Hz ±0.5dB - Audio Input Level: -15db, Max -30db - Audio Input Connector: RCA type - AUX Input Connector: none - Operating temperature range: -10 to 45 ℃ - Size of Transmitter Unit: 483mm * 400mm * 88mm (19" Standard 2U case) - Shipping Weight: 11.5Kg boujour  le circuit  RF a changer  le site pour répare au http://www.warner-rf.com  ou  au https://www.elecsky.com/

FM Broadcast pallet, solid copper base 6 mm, bias adjust, high quality roger PCB and capacitors. It is tuned on 70 - 110 Mhz FM band. It may modifed for 144 Mhz HAM radio operations.  It may work with BLF578, BFF188, 188XR and other LD MOS, even if less powerfull like MRF151G (300 W).  Fully tested. 

RVR PTX-30 - MADE IN ITALY PROFESSIONAL FM BROADCAST TRANSMITTER + included stereo coder  ELENOS MAX AMPLIFIED POWER  30-50 W EVERYTHING IS WORKING ! THIS IS A SERIOUS SELLING. BUY WITH CONFIDENCE. I CAN SHIP WORLDWIDE, THIS IS A VERY HEAVY ITEM AND I WILL PACK IT SOLID ! SHIPPING TO FRANCE: 15 EUROS EUROPE: 30 EUROS WORLD:  45 EUROS

Includes  1x RTL-SDR Blog Broadcast FM Band-Stop Filter 1x SMA male to SMA male adapter Blocks the broadcast FM band between 88 – 108 MHz with over 50dB of attenuation.  Designed for maximum attenuation between 88 - 108 MHz and the 3dB roll off points are at 76 MHz and 122 MHz. Insertion loss is less than 0.5 dB between 0 – 1 GHz, and mostly less than 1.5 dB between 1 – 3 GHz.  Uses SMA female connectors. Comes with a free SMA male to SMA male adapter. A broadcast FM block filter can help if you have very strong broadcasts in your area that are overloading the SDR dongle. Also known as “FM Trap”. Notes: RX filter only. Designed for SDR users, but might also be useful for TV users struggling with FM interference. But TV users please carefully check the spectrum analyzer graphs and 3dB roll off points to ensure that it will not block a TV signal of interest. e.g. Channels between 76 - 88 MHz could be attenuated enough to lose reception.   Includes  1x RTL-SDR Blog Broadcast FM Band-Stop Filter 1x SMA male to SMA male adapter Blocks the broadcast FM band between 88 – 108 MHz with over 50dB of attenuation.  Designed for maximum attenuation between 88 - 108 MHz and the 3dB roll off points are at 76 MHz and 122 MHz. Insertion loss is less than 0.5 dB between 0 – 1 GHz, and mostly less than 1.5 dB between 1 – 3 GHz.  Uses SMA female connectors. Comes with a free SMA male to SMA male adapter. A broadcast FM block filter can help if you have very strong broadcasts in your area that are overloading the SDR dongle. Also known as “FM Trap”. Notes: RX filter only. Designed for SDR users, but might also be useful for TV users struggling with FM interference. But TV users please carefully check the spectrum analyzer graphs and 3dB roll off points to ensure that it will not block a TV signal of interest. e.g. Channels between 76 - 88 MHz could be attenuated enough to lose reception. Le 09-juil.-19 à 18:28:20 Paris, le vendeur a ajouté les informations suivantes:

Includes  1x RTL-SDR Blog Broadcast FM Band-Stop Filter 1x SMA male to SMA male adapter Blocks the broadcast FM band between 88 – 108 MHz with over 50dB of attenuation.  Designed for maximum attenuation between 88 - 108 MHz and the 3dB roll off points are at 76 MHz and 122 MHz. Insertion loss is less than 0.5 dB between 0 – 1 GHz, and mostly less than 1.5 dB between 1 – 3 GHz.  Uses SMA female connectors. Comes with a free SMA male to SMA male adapter. A broadcast FM block filter can help if you have very strong broadcasts in your area that are overloading the SDR dongle. Also known as “FM Trap”. Notes: RX filter only. Designed for SDR users, but might also be useful for TV users struggling with FM interference. But TV users please carefully check the spectrum analyzer graphs and 3dB roll off points to ensure that it will not block a TV signal of interest. e.g. Channels between 76 - 88 MHz could be attenuated enough to lose reception. Le 06-mai-19 à 11:31:52 Paris, le vendeur a ajouté les informations suivantes:

Includes  1x RTL-SDR Blog Broadcast FM Band-Stop Filter 1x SMA male to SMA male adapter Blocks the broadcast FM band between 88 – 108 MHz with over 50dB of attenuation.  Designed for maximum attenuation between 88 - 108 MHz and the 3dB roll off points are at 76 MHz and 122 MHz. Insertion loss is less than 0.5 dB between 0 – 1 GHz, and mostly less than 1.5 dB between 1 – 3 GHz.  Uses SMA female connectors. Comes with a free SMA male to SMA male adapter. A broadcast FM block filter can help if you have very strong broadcasts in your area that are overloading the SDR dongle. Also known as “FM Trap”. Notes: RX filter only. Designed for SDR users, but might also be useful for TV users struggling with FM interference. But TV users please carefully check the spectrum analyzer graphs and 3dB roll off points to ensure that it will not block a TV signal of interest. e.g. Channels between 76 - 88 MHz could be attenuated enough to lose reception. Le 21-mai-19 à 18:55:04 Paris, le vendeur a ajouté les informations suivantes:

Includes  1x RTL-SDR Blog Broadcast FM Band-Stop Filter 1x SMA male to SMA male adapter Blocks the broadcast FM band between 88 – 108 MHz with over 50dB of attenuation.  Designed for maximum attenuation between 88 - 108 MHz and the 3dB roll off points are at 76 MHz and 122 MHz. Insertion loss is less than 0.5 dB between 0 – 1 GHz, and mostly less than 1.5 dB between 1 – 3 GHz.  Uses SMA female connectors. Comes with a free SMA male to SMA male adapter. A broadcast FM block filter can help if you have very strong broadcasts in your area that are overloading the SDR dongle. Also known as “FM Trap”. Notes: RX filter only. Designed for SDR users, but might also be useful for TV users struggling with FM interference. But TV users please carefully check the spectrum analyzer graphs and 3dB roll off points to ensure that it will not block a TV signal of interest. e.g. Channels between 76 - 88 MHz could be attenuated enough to lose reception. Le 08-juil.-19 à 16:50:21 Paris, le vendeur a ajouté les informations suivantes:

Includes  1x RTL-SDR Blog Broadcast FM Band-Stop Filter 1x SMA male to SMA male adapter Blocks the broadcast FM band between 88 – 108 MHz with over 50dB of attenuation.  Designed for maximum attenuation between 88 - 108 MHz and the 3dB roll off points are at 76 MHz and 122 MHz. Insertion loss is less than 0.5 dB between 0 – 1 GHz, and mostly less than 1.5 dB between 1 – 3 GHz.  Uses SMA female connectors. Comes with a free SMA male to SMA male adapter. A broadcast FM block filter can help if you have very strong broadcasts in your area that are overloading the SDR dongle. Also known as “FM Trap”. Notes: RX filter only. Designed for SDR users, but might also be useful for TV users struggling with FM interference. But TV users please carefully check the spectrum analyzer graphs and 3dB roll off points to ensure that it will not block a TV signal of interest. e.g. Channels between 76 - 88 MHz could be attenuated enough to lose reception. Le 08-juil.-19 à 10:31:14 Paris, le vendeur a ajouté les informations suivantes: