Frame led hd high

Caractéristiques:. 100% tout neuf et de haute qualité Soutenir la prise casque Haut-parleurs intégrés (2 x 1.5W), joue de la musique... Expédition depuis la Chine dans 48h - Livraison sous 10 à 20 jours ouvrés.

Specification: LED Strip Size: 540mm x 4mm Driver board size:7x2cm Input:DC 10-30V OutPut:7.5V-9.6V Features: * The product of the original display-specific lights, high brightness, can not look directly * LED particles close, high-density arrangement bright LED SMD imports * Long life, is a display design, the life of 100,000 hours * Easy to install, use double-sided tape can be attached to the original LCD display tank, or posted elsewhere * Energy saving, power only 8W. Original four LCD power is generally 24W. Brief installation instructions: If your monitor is a high pressure plate, this pressure plate into a direct replacement driver board like if your monitor is one of the high-voltage power supply board, then: one version of the high-pressure electricity, find 12V (capacitance), then pull swap power supply with a multimeter to find and 12V (capacitance) is connected to the negative originals off, boost board then three lines 12V, ON, GND, 12V 12V positive electrode plate with high pressure booster is integrally connected to the board, GND with negative connected, oN even oN / OFF. it is simply the original high-voltage power supply is disconnected to replace the booster plate at the front end of the original pressure to take power. The following are the installation instructions for reference (for reference only): Easy modification steps: 1, open the metal frame: 2, cut the inner plastic protective frame angle: 3, out of the liquid crystal lamp: 4, insert the LED light bar Note, this modification method is simple, easy to light leakage. But it will destroy the border. Normal method: 1, open to protect the metal frame with a simple conversion step. 2. Remove the LCD glass panel (panel carefully on soft cable, such as careless easy to qualify and broadband) 3. Remove the plastic inner frame and lighthouse (Be careful not to get dirty fouling within the backlight assembly) 4. Remove the inner lamp lighthouse 5, LED light bar affixed inside the lighthouse 6, then restore the original removal steps carefully 7. Replace the glass panels and metal frame test 8, installed lights. Package Includes: 2x LED strips 1x Driver board 1x cable   Specification: LED Strip Size: 540mm x 4mm Driver board size:7x2cm Input:DC 10-30V OutPut:7.5V-9.6V Features: * The product of the original display-specific lights, high brightness, can not look directly * LED particles close, high-density arrangement bright LED SMD imports * Long life, is a display design, the life of 100,000 hours * Easy to install, use double-sided tape can be attached to the original LCD display tank, or posted elsewhere * Energy saving, power only 8W. Original four LCD power is generally 24W. Brief installation instructions: If your monitor is a high pressure plate, this pressure plate into a direct replacement driver board like if your monitor is one of the high-voltage power supply board, then: one version of the high-pressure electricity, find 12V (capacitance), then pull swap power supply with a multimeter to find and 12V (capacitance) is connected to the negative originals off, boost board then three lines 12V, ON, GND, 12V 12V positive electrode plate with high pressure booster is integrally connected to the board, GND with negative connected, oN even oN / OFF. it is simply the original high-voltage power supply is disconnected to replace the booster plate at the front end of the original pressure to take power. The following are the installation instructions for reference (for reference only): Easy modification steps: 1, open the metal frame: 2, cut the inner plastic protective frame angle: 3, out of the liquid crystal lamp: 4, insert the LED light bar Note, this modification method is simple, easy to light leakage. But it will destroy the border. Normal method: 1, open to protect the metal frame with a simple conversion step. 2. Remove the LCD glass panel (panel carefully on soft cable, such as careless easy to qualify and broadband) 3. Remove the plastic inner frame and lighthouse (Be careful not to get dirty fouling within the backlight assembly) 4. Remove the inner lamp lighthouse 5, LED light bar affixed inside the lighthouse 6, then restore the original removal steps carefully 7. Replace the glass panels and metal frame test 8, installed lights. Package Includes: 2x LED strips 1x Driver board 1x cable Le 02-avr.-19 à 09:52:29 Paris, le vendeur a ajouté les informations suivantes:

Specification: LED Strip Size: 540mm x 4mm Driver board size:7x2cm Input:DC 10-30V OutPut:7.5V-9.6V Features: * The product of the original display-specific lights, high brightness, can not look directly * LED particles close, high-density arrangement bright LED SMD imports * Long life, is a display design, the life of 100,000 hours * Easy to install, use double-sided tape can be attached to the original LCD display tank, or posted elsewhere * Energy saving, power only 8W. Original four LCD power is generally 24W. Brief installation instructions: If your monitor is a high pressure plate, this pressure plate into a direct replacement driver board like if your monitor is one of the high-voltage power supply board, then: one version of the high-pressure electricity, find 12V (capacitance), then pull swap power supply with a multimeter to find and 12V (capacitance) is connected to the negative originals off, boost board then three lines 12V, ON, GND, 12V 12V positive electrode plate with high pressure booster is integrally connected to the board, GND with negative connected, oN even oN / OFF. it is simply the original high-voltage power supply is disconnected to replace the booster plate at the front end of the original pressure to take power. The following are the installation instructions for reference (for reference only): Easy modification steps: 1, open the metal frame: 2, cut the inner plastic protective frame angle: 3, out of the liquid crystal lamp: 4, insert the LED light bar Note, this modification method is simple, easy to light leakage. But it will destroy the border. Normal method: 1, open to protect the metal frame with a simple conversion step. 2. Remove the LCD glass panel (panel carefully on soft cable, such as careless easy to qualify and broadband) 3. Remove the plastic inner frame and lighthouse (Be careful not to get dirty fouling within the backlight assembly) 4. Remove the inner lamp lighthouse 5, LED light bar affixed inside the lighthouse 6, then restore the original removal steps carefully 7. Replace the glass panels and metal frame test 8, installed lights. Package Includes: 2x LED strips 1x Driver board 1x cable   Specification: LED Strip Size: 540mm x 4mm Driver board size:7x2cm Input:DC 10-30V OutPut:7.5V-9.6V Features: * The product of the original display-specific lights, high brightness, can not look directly * LED particles close, high-density arrangement bright LED SMD imports * Long life, is a display design, the life of 100,000 hours * Easy to install, use double-sided tape can be attached to the original LCD display tank, or posted elsewhere * Energy saving, power only 8W. Original four LCD power is generally 24W. Brief installation instructions: If your monitor is a high pressure plate, this pressure plate into a direct replacement driver board like if your monitor is one of the high-voltage power supply board, then: one version of the high-pressure electricity, find 12V (capacitance), then pull swap power supply with a multimeter to find and 12V (capacitance) is connected to the negative originals off, boost board then three lines 12V, ON, GND, 12V 12V positive electrode plate with high pressure booster is integrally connected to the board, GND with negative connected, oN even oN / OFF. it is simply the original high-voltage power supply is disconnected to replace the booster plate at the front end of the original pressure to take power. The following are the installation instructions for reference (for reference only): Easy modification steps: 1, open the metal frame: 2, cut the inner plastic protective frame angle: 3, out of the liquid crystal lamp: 4, insert the LED light bar Note, this modification method is simple, easy to light leakage. But it will destroy the border. Normal method: 1, open to protect the metal frame with a simple conversion step. 2. Remove the LCD glass panel (panel carefully on soft cable, such as careless easy to qualify and broadband) 3. Remove the plastic inner frame and lighthouse (Be careful not to get dirty fouling within the backlight assembly) 4. Remove the inner lamp lighthouse 5, LED light bar affixed inside the lighthouse 6, then restore the original removal steps carefully 7. Replace the glass panels and metal frame test 8, installed lights. Package Includes: 2x LED strips 1x Driver board 1x cable Le 05-sept.-19 à 22:14:30 Paris, le vendeur a ajouté les informations suivantes:

Specification: LED Strip Size: 540mm x 4mm Driver board size:7x2cm Input:DC 10-30V OutPut:7.5V-9.6V Features: * The product of the original display-specific lights, high brightness, can not look directly * LED particles close, high-density arrangement bright LED SMD imports * Long life, is a display design, the life of 100,000 hours * Easy to install, use double-sided tape can be attached to the original LCD display tank, or posted elsewhere * Energy saving, power only 8W. Original four LCD power is generally 24W. Brief installation instructions: If your monitor is a high pressure plate, this pressure plate into a direct replacement driver board like if your monitor is one of the high-voltage power supply board, then: one version of the high-pressure electricity, find 12V (capacitance), then pull swap power supply with a multimeter to find and 12V (capacitance) is connected to the negative originals off, boost board then three lines 12V, ON, GND, 12V 12V positive electrode plate with high pressure booster is integrally connected to the board, GND with negative connected, oN even oN / OFF. it is simply the original high-voltage power supply is disconnected to replace the booster plate at the front end of the original pressure to take power. The following are the installation instructions for reference (for reference only): Easy modification steps: 1, open the metal frame: 2, cut the inner plastic protective frame angle: 3, out of the liquid crystal lamp: 4, insert the LED light bar Note, this modification method is simple, easy to light leakage. But it will destroy the border. Normal method: 1, open to protect the metal frame with a simple conversion step. 2. Remove the LCD glass panel (panel carefully on soft cable, such as careless easy to qualify and broadband) 3. Remove the plastic inner frame and lighthouse (Be careful not to get dirty fouling within the backlight assembly) 4. Remove the inner lamp lighthouse 5, LED light bar affixed inside the lighthouse 6, then restore the original removal steps carefully 7. Replace the glass panels and metal frame test 8, installed lights. Package Includes: 2x LED strips 1x Driver board 1x cable   Specification: LED Strip Size: 540mm x 4mm Driver board size:7x2cm Input:DC 10-30V OutPut:7.5V-9.6V Features: * The product of the original display-specific lights, high brightness, can not look directly * LED particles close, high-density arrangement bright LED SMD imports * Long life, is a display design, the life of 100,000 hours * Easy to install, use double-sided tape can be attached to the original LCD display tank, or posted elsewhere * Energy saving, power only 8W. Original four LCD power is generally 24W. Brief installation instructions: If your monitor is a high pressure plate, this pressure plate into a direct replacement driver board like if your monitor is one of the high-voltage power supply board, then: one version of the high-pressure electricity, find 12V (capacitance), then pull swap power supply with a multimeter to find and 12V (capacitance) is connected to the negative originals off, boost board then three lines 12V, ON, GND, 12V 12V positive electrode plate with high pressure booster is integrally connected to the board, GND with negative connected, oN even oN / OFF. it is simply the original high-voltage power supply is disconnected to replace the booster plate at the front end of the original pressure to take power. The following are the installation instructions for reference (for reference only): Easy modification steps: 1, open the metal frame: 2, cut the inner plastic protective frame angle: 3, out of the liquid crystal lamp: 4, insert the LED light bar Note, this modification method is simple, easy to light leakage. But it will destroy the border. Normal method: 1, open to protect the metal frame with a simple conversion step. 2. Remove the LCD glass panel (panel carefully on soft cable, such as careless easy to qualify and broadband) 3. Remove the plastic inner frame and lighthouse (Be careful not to get dirty fouling within the backlight assembly) 4. Remove the inner lamp lighthouse 5, LED light bar affixed inside the lighthouse 6, then restore the original removal steps carefully 7. Replace the glass panels and metal frame test 8, installed lights. Package Includes: 2x LED strips 1x Driver board 1x cable Le 04-sept.-19 à 18:24:09 Paris, le vendeur a ajouté les informations suivantes:

Specification: LED Strip Size: 540mm x 4mm Driver board size:7x2cm Input:DC 10-30V OutPut:7.5V-9.6V Features: * The product of the original display-specific lights, high brightness, can not look directly * LED particles close, high-density arrangement bright LED SMD imports * Long life, is a display design, the life of 100,000 hours * Easy to install, use double-sided tape can be attached to the original LCD display tank, or posted elsewhere * Energy saving, power only 8W. Original four LCD power is generally 24W. Brief installation instructions: If your monitor is a high pressure plate, this pressure plate into a direct replacement driver board like if your monitor is one of the high-voltage power supply board, then: one version of the high-pressure electricity, find 12V (capacitance), then pull swap power supply with a multimeter to find and 12V (capacitance) is connected to the negative originals off, boost board then three lines 12V, ON, GND, 12V 12V positive electrode plate with high pressure booster is integrally connected to the board, GND with negative connected, oN even oN / OFF. it is simply the original high-voltage power supply is disconnected to replace the booster plate at the front end of the original pressure to take power. The following are the installation instructions for reference (for reference only): Easy modification steps: 1, open the metal frame: 2, cut the inner plastic protective frame angle: 3, out of the liquid crystal lamp: 4, insert the LED light bar Note, this modification method is simple, easy to light leakage. But it will destroy the border. Normal method: 1, open to protect the metal frame with a simple conversion step. 2. Remove the LCD glass panel (panel carefully on soft cable, such as careless easy to qualify and broadband) 3. Remove the plastic inner frame and lighthouse (Be careful not to get dirty fouling within the backlight assembly) 4. Remove the inner lamp lighthouse 5, LED light bar affixed inside the lighthouse 6, then restore the original removal steps carefully 7. Replace the glass panels and metal frame test 8, installed lights. Package Includes: 2x LED strips 1x Driver board 1x cable   Le 24-déc.-18 à 13:37:18 Paris, le vendeur a ajouté les informations suivantes:

Specification: LED Strip Size: 540mm x 4mm Driver board size:7x2cm Input:DC 10-30V OutPut:7.5V-9.6V Features: * The product of the original display-specific lights, high brightness, can not look directly * LED particles close, high-density arrangement bright LED SMD imports * Long life, is a display design, the life of 100,000 hours * Easy to install, use double-sided tape can be attached to the original LCD display tank, or posted elsewhere * Energy saving, power only 8W. Original four LCD power is generally 24W. Brief installation instructions: If your monitor is a high pressure plate, this pressure plate into a direct replacement driver board like if your monitor is one of the high-voltage power supply board, then: one version of the high-pressure electricity, find 12V (capacitance), then pull swap power supply with a multimeter to find and 12V (capacitance) is connected to the negative originals off, boost board then three lines 12V, ON, GND, 12V 12V positive electrode plate with high pressure booster is integrally connected to the board, GND with negative connected, oN even oN / OFF. it is simply the original high-voltage power supply is disconnected to replace the booster plate at the front end of the original pressure to take power. The following are the installation instructions for reference (for reference only): Easy modification steps: 1, open the metal frame: 2, cut the inner plastic protective frame angle: 3, out of the liquid crystal lamp: 4, insert the LED light bar Note, this modification method is simple, easy to light leakage. But it will destroy the border. Normal method: 1, open to protect the metal frame with a simple conversion step. 2. Remove the LCD glass panel (panel carefully on soft cable, such as careless easy to qualify and broadband) 3. Remove the plastic inner frame and lighthouse (Be careful not to get dirty fouling within the backlight assembly) 4. Remove the inner lamp lighthouse 5, LED light bar affixed inside the lighthouse 6, then restore the original removal steps carefully 7. Replace the glass panels and metal frame test 8, installed lights. Package Includes: 2x LED strips 1x Driver board 1x cable Le 02-avr.-19 à 12:08:11 Paris, le vendeur a ajouté les informations suivantes:

Specification: LED Strip Size: 540mm x 4mm Driver board size:7x2cm Input:DC 10-30V OutPut:7.5V-9.6V Features: * The product of the original display-specific lights, high brightness, can not look directly * LED particles close, high-density arrangement bright LED SMD imports * Long life, is a display design, the life of 100,000 hours * Easy to install, use double-sided tape can be attached to the original LCD display tank, or posted elsewhere * Energy saving, power only 8W. Original four LCD power is generally 24W. Brief installation instructions: If your monitor is a high pressure plate, this pressure plate into a direct replacement driver board like if your monitor is one of the high-voltage power supply board, then: one version of the high-pressure electricity, find 12V (capacitance), then pull swap power supply with a multimeter to find and 12V (capacitance) is connected to the negative originals off, boost board then three lines 12V, ON, GND, 12V 12V positive electrode plate with high pressure booster is integrally connected to the board, GND with negative connected, oN even oN / OFF. it is simply the original high-voltage power supply is disconnected to replace the booster plate at the front end of the original pressure to take power. The following are the installation instructions for reference (for reference only): Easy modification steps: 1, open the metal frame: 2, cut the inner plastic protective frame angle: 3, out of the liquid crystal lamp: 4, insert the LED light bar Note, this modification method is simple, easy to light leakage. But it will destroy the border. Normal method: 1, open to protect the metal frame with a simple conversion step. 2. Remove the LCD glass panel (panel carefully on soft cable, such as careless easy to qualify and broadband) 3. Remove the plastic inner frame and lighthouse (Be careful not to get dirty fouling within the backlight assembly) 4. Remove the inner lamp lighthouse 5, LED light bar affixed inside the lighthouse 6, then restore the original removal steps carefully 7. Replace the glass panels and metal frame test 8, installed lights. Package Includes: 2x LED strips 1x Driver board 1x cable Le 01-avr.-19 à 13:08:56 Paris, le vendeur a ajouté les informations suivantes:

  Specification: LED Strip Size: 540mm x 4mm Driver board size:7x2cm Input:DC 10-30V OutPut:7.5V-9.6V Features: * The product of the original display-specific lights, high brightness, can not look directly * LED particles close, high-density arrangement bright LED SMD imports * Long life, is a display design, the life of 100,000 hours * Easy to install, use double-sided tape can be attached to the original LCD display tank, or posted elsewhere * Energy saving, power only 8W. Original four LCD power is generally 24W. Brief installation instructions: If your monitor is a high pressure plate, this pressure plate into a direct replacement driver board like if your monitor is one of the high-voltage power supply board, then: one version of the high-pressure electricity, find 12V (capacitance), then pull swap power supply with a multimeter to find and 12V (capacitance) is connected to the negative originals off, boost board then three lines 12V, ON, GND, 12V 12V positive electrode plate with high pressure booster is integrally connected to the board, GND with negative connected, oN even oN / OFF. it is simply the original high-voltage power supply is disconnected to replace the booster plate at the front end of the original pressure to take power. The following are the installation instructions for reference (for reference only): Easy modification steps: 1, open the metal frame: 2, cut the inner plastic protective frame angle: 3, out of the liquid crystal lamp: 4, insert the LED light bar Note, this modification method is simple, easy to light leakage. But it will destroy the border. Normal method: 1, open to protect the metal frame with a simple conversion step. 2. Remove the LCD glass panel (panel carefully on soft cable, such as careless easy to qualify and broadband) 3. Remove the plastic inner frame and lighthouse (Be careful not to get dirty fouling within the backlight assembly) 4. Remove the inner lamp lighthouse 5, LED light bar affixed inside the lighthouse 6, then restore the original removal steps carefully 7. Replace the glass panels and metal frame test 8, installed lights. Package Includes: 2x LED strips 1x Driver board 1x cable     Le 09-mai-19 à 05:43:10 Paris, le vendeur a ajouté les informations suivantes:

Specification: LED Strip Size: 540mm x 4mm Driver board size:7x2cm Input:DC 10-30V OutPut:7.5V-9.6V Features: * The product of the original display-specific lights, high brightness, can not look directly * LED particles close, high-density arrangement bright LED SMD imports * Long life, is a display design, the life of 100,000 hours * Easy to install, use double-sided tape can be attached to the original LCD display tank, or posted elsewhere * Energy saving, power only 8W. Original four LCD power is generally 24W. Brief installation instructions: If your monitor is a high pressure plate, this pressure plate into a direct replacement driver board like if your monitor is one of the high-voltage power supply board, then: one version of the high-pressure electricity, find 12V (capacitance), then pull swap power supply with a multimeter to find and 12V (capacitance) is connected to the negative originals off, boost board then three lines 12V, ON, GND, 12V 12V positive electrode plate with high pressure booster is integrally connected to the board, GND with negative connected, oN even oN / OFF. it is simply the original high-voltage power supply is disconnected to replace the booster plate at the front end of the original pressure to take power. The following are the installation instructions for reference (for reference only): Easy modification steps: 1, open the metal frame: 2, cut the inner plastic protective frame angle: 3, out of the liquid crystal lamp: 4, insert the LED light bar Note, this modification method is simple, easy to light leakage. But it will destroy the border. Normal method: 1, open to protect the metal frame with a simple conversion step. 2. Remove the LCD glass panel (panel carefully on soft cable, such as careless easy to qualify and broadband) 3. Remove the plastic inner frame and lighthouse (Be careful not to get dirty fouling within the backlight assembly) 4. Remove the inner lamp lighthouse 5, LED light bar affixed inside the lighthouse 6, then restore the original removal steps carefully 7. Replace the glass panels and metal frame test 8, installed lights. Package Includes: 2x LED strips 1x Driver board 1x cable Le 06-mai-19 à 09:56:09 Paris, le vendeur a ajouté les informations suivantes:

Specification: LED Strip Size: 540mm x 4mm Driver board size:7x2cm Input:DC 10-30V OutPut:7.5V-9.6V Features: * The product of the original display-specific lights, high brightness, can not look directly * LED particles close, high-density arrangement bright LED SMD imports * Long life, is a display design, the life of 100,000 hours * Easy to install, use double-sided tape can be attached to the original LCD display tank, or posted elsewhere * Energy saving, power only 8W. Original four LCD power is generally 24W. Brief installation instructions: If your monitor is a high pressure plate, this pressure plate into a direct replacement driver board like if your monitor is one of the high-voltage power supply board, then: one version of the high-pressure electricity, find 12V (capacitance), then pull swap power supply with a multimeter to find and 12V (capacitance) is connected to the negative originals off, boost board then three lines 12V, ON, GND, 12V 12V positive electrode plate with high pressure booster is integrally connected to the board, GND with negative connected, oN even oN / OFF. it is simply the original high-voltage power supply is disconnected to replace the booster plate at the front end of the original pressure to take power. The following are the installation instructions for reference (for reference only): Easy modification steps: 1, open the metal frame: 2, cut the inner plastic protective frame angle: 3, out of the liquid crystal lamp: 4, insert the LED light bar Note, this modification method is simple, easy to light leakage. But it will destroy the border. Normal method: 1, open to protect the metal frame with a simple conversion step. 2. Remove the LCD glass panel (panel carefully on soft cable, such as careless easy to qualify and broadband) 3. Remove the plastic inner frame and lighthouse (Be careful not to get dirty fouling within the backlight assembly) 4. Remove the inner lamp lighthouse 5, LED light bar affixed inside the lighthouse 6, then restore the original removal steps carefully 7. Replace the glass panels and metal frame test 8, installed lights. Package Includes: 2x LED strips 1x Driver board 1x cable Le 06-mai-19 à 07:54:08 Paris, le vendeur a ajouté les informations suivantes:

Specification: LED Strip Size: 540mm x 4mm Driver board size:7x2cm Input:DC 10-30V OutPut:7.5V-9.6V Features: * The product of the original display-specific lights, high brightness, can not look directly * LED particles close, high-density arrangement bright LED SMD imports * Long life, is a display design, the life of 100,000 hours * Easy to install, use double-sided tape can be attached to the original LCD display tank, or posted elsewhere * Energy saving, power only 8W. Original four LCD power is generally 24W. Brief installation instructions: If your monitor is a high pressure plate, this pressure plate into a direct replacement driver board like if your monitor is one of the high-voltage power supply board, then: one version of the high-pressure electricity, find 12V (capacitance), then pull swap power supply with a multimeter to find and 12V (capacitance) is connected to the negative originals off, boost board then three lines 12V, ON, GND, 12V 12V positive electrode plate with high pressure booster is integrally connected to the board, GND with negative connected, oN even oN / OFF. it is simply the original high-voltage power supply is disconnected to replace the booster plate at the front end of the original pressure to take power. The following are the installation instructions for reference (for reference only): Easy modification steps: 1, open the metal frame: 2, cut the inner plastic protective frame angle: 3, out of the liquid crystal lamp: 4, insert the LED light bar Note, this modification method is simple, easy to light leakage. But it will destroy the border. Normal method: 1, open to protect the metal frame with a simple conversion step. 2. Remove the LCD glass panel (panel carefully on soft cable, such as careless easy to qualify and broadband) 3. Remove the plastic inner frame and lighthouse (Be careful not to get dirty fouling within the backlight assembly) 4. Remove the inner lamp lighthouse 5, LED light bar affixed inside the lighthouse 6, then restore the original removal steps carefully 7. Replace the glass panels and metal frame test 8, installed lights. Package Includes: 2x LED strips 1x Driver board 1x cable Le 06-juin-19 à 13:31:05 Paris, le vendeur a ajouté les informations suivantes:

  Specification: LED Strip Size: 540mm x 4mm Driver board size:7x2cm Input:DC 10-30V OutPut:7.5V-9.6V Features: * The product of the original display-specific lights, high brightness, can not look directly * LED particles close, high-density arrangement bright LED SMD imports * Long life, is a display design, the life of 100,000 hours * Easy to install, use double-sided tape can be attached to the original LCD display tank, or posted elsewhere * Energy saving, power only 8W. Original four LCD power is generally 24W. Brief installation instructions: If your monitor is a high pressure plate, this pressure plate into a direct replacement driver board like if your monitor is one of the high-voltage power supply board, then: one version of the high-pressure electricity, find 12V (capacitance), then pull swap power supply with a multimeter to find and 12V (capacitance) is connected to the negative originals off, boost board then three lines 12V, ON, GND, 12V 12V positive electrode plate with high pressure booster is integrally connected to the board, GND with negative connected, oN even oN / OFF. it is simply the original high-voltage power supply is disconnected to replace the booster plate at the front end of the original pressure to take power. The following are the installation instructions for reference (for reference only): Easy modification steps: 1, open the metal frame: 2, cut the inner plastic protective frame angle: 3, out of the liquid crystal lamp: 4, insert the LED light bar Note, this modification method is simple, easy to light leakage. But it will destroy the border. Normal method: 1, open to protect the metal frame with a simple conversion step. 2. Remove the LCD glass panel (panel carefully on soft cable, such as careless easy to qualify and broadband) 3. Remove the plastic inner frame and lighthouse (Be careful not to get dirty fouling within the backlight assembly) 4. Remove the inner lamp lighthouse 5, LED light bar affixed inside the lighthouse 6, then restore the original removal steps carefully 7. Replace the glass panels and metal frame test 8, installed lights. Package Includes: 2x LED strips 1x Driver board 1x cable     Le 08-juil.-19 à 08:14:13 Paris, le vendeur a ajouté les informations suivantes:

Specification: LED Strip Size: 540mm x 4mm Driver board size:7x2cm Input:DC 10-30V OutPut:7.5V-9.6V Features: * The product of the original display-specific lights, high brightness, can not look directly * LED particles close, high-density arrangement bright LED SMD imports * Long life, is a display design, the life of 100,000 hours * Easy to install, use double-sided tape can be attached to the original LCD display tank, or posted elsewhere * Energy saving, power only 8W. Original four LCD power is generally 24W. Brief installation instructions: If your monitor is a high pressure plate, this pressure plate into a direct replacement driver board like if your monitor is one of the high-voltage power supply board, then: one version of the high-pressure electricity, find 12V (capacitance), then pull swap power supply with a multimeter to find and 12V (capacitance) is connected to the negative originals off, boost board then three lines 12V, ON, GND, 12V 12V positive electrode plate with high pressure booster is integrally connected to the board, GND with negative connected, oN even oN / OFF. it is simply the original high-voltage power supply is disconnected to replace the booster plate at the front end of the original pressure to take power. The following are the installation instructions for reference (for reference only): Easy modification steps: 1, open the metal frame: 2, cut the inner plastic protective frame angle: 3, out of the liquid crystal lamp: 4, insert the LED light bar Note, this modification method is simple, easy to light leakage. But it will destroy the border. Normal method: 1, open to protect the metal frame with a simple conversion step. 2. Remove the LCD glass panel (panel carefully on soft cable, such as careless easy to qualify and broadband) 3. Remove the plastic inner frame and lighthouse (Be careful not to get dirty fouling within the backlight assembly) 4. Remove the inner lamp lighthouse 5, LED light bar affixed inside the lighthouse 6, then restore the original removal steps carefully 7. Replace the glass panels and metal frame test 8, installed lights. Package Includes: 2x LED strips 1x Driver board 1x cable   Le 20-juil.-19 à 16:13:15 Paris, le vendeur a ajouté les informations suivantes:

Specification: LED Strip Size: 540mm x 4mm Driver board size:7x2cm Input:DC 10-30V OutPut:7.5V-9.6V Features: * The product of the original display-specific lights, high brightness, can not look directly * LED particles close, high-density arrangement bright LED SMD imports * Long life, is a display design, the life of 100,000 hours * Easy to install, use double-sided tape can be attached to the original LCD display tank, or posted elsewhere * Energy saving, power only 8W. Original four LCD power is generally 24W. Brief installation instructions: If your monitor is a high pressure plate, this pressure plate into a direct replacement driver board like if your monitor is one of the high-voltage power supply board, then: one version of the high-pressure electricity, find 12V (capacitance), then pull swap power supply with a multimeter to find and 12V (capacitance) is connected to the negative originals off, boost board then three lines 12V, ON, GND, 12V 12V positive electrode plate with high pressure booster is integrally connected to the board, GND with negative connected, oN even oN / OFF. it is simply the original high-voltage power supply is disconnected to replace the booster plate at the front end of the original pressure to take power. The following are the installation instructions for reference (for reference only): Easy modification steps: 1, open the metal frame: 2, cut the inner plastic protective frame angle: 3, out of the liquid crystal lamp: 4, insert the LED light bar Note, this modification method is simple, easy to light leakage. But it will destroy the border. Normal method: 1, open to protect the metal frame with a simple conversion step. 2. Remove the LCD glass panel (panel carefully on soft cable, such as careless easy to qualify and broadband) 3. Remove the plastic inner frame and lighthouse (Be careful not to get dirty fouling within the backlight assembly) 4. Remove the inner lamp lighthouse 5, LED light bar affixed inside the lighthouse 6, then restore the original removal steps carefully 7. Replace the glass panels and metal frame test 8, installed lights. Package Includes: 2x LED strips 1x Driver board 1x cable Le 17-juil.-19 à 09:19:16 Paris, le vendeur a ajouté les informations suivantes:

  Specification: LED Strip Size: 540mm x 4mm Driver board size:7x2cm Input:DC 10-30V OutPut:7.5V-9.6V Features: * The product of the original display-specific lights, high brightness, can not look directly * LED particles close, high-density arrangement bright LED SMD imports * Long life, is a display design, the life of 100,000 hours * Easy to install, use double-sided tape can be attached to the original LCD display tank, or posted elsewhere * Energy saving, power only 8W. Original four LCD power is generally 24W. Brief installation instructions: If your monitor is a high pressure plate, this pressure plate into a direct replacement driver board like if your monitor is one of the high-voltage power supply board, then: one version of the high-pressure electricity, find 12V (capacitance), then pull swap power supply with a multimeter to find and 12V (capacitance) is connected to the negative originals off, boost board then three lines 12V, ON, GND, 12V 12V positive electrode plate with high pressure booster is integrally connected to the board, GND with negative connected, oN even oN / OFF. it is simply the original high-voltage power supply is disconnected to replace the booster plate at the front end of the original pressure to take power. The following are the installation instructions for reference (for reference only): Easy modification steps: 1, open the metal frame: 2, cut the inner plastic protective frame angle: 3, out of the liquid crystal lamp: 4, insert the LED light bar Note, this modification method is simple, easy to light leakage. But it will destroy the border. Normal method: 1, open to protect the metal frame with a simple conversion step. 2. Remove the LCD glass panel (panel carefully on soft cable, such as careless easy to qualify and broadband) 3. Remove the plastic inner frame and lighthouse (Be careful not to get dirty fouling within the backlight assembly) 4. Remove the inner lamp lighthouse 5, LED light bar affixed inside the lighthouse 6, then restore the original removal steps carefully 7. Replace the glass panels and metal frame test 8, installed lights. Package Includes: 2x LED strips 1x Driver board 1x cable     Le 13-juil.-19 à 14:54:17 Paris, le vendeur a ajouté les informations suivantes:

  Specification: LED Strip Size: 540mm x 4mm Driver board size:7x2cm Input:DC 10-30V OutPut:7.5V-9.6V Features: * The product of the original display-specific lights, high brightness, can not look directly * LED particles close, high-density arrangement bright LED SMD imports * Long life, is a display design, the life of 100,000 hours * Easy to install, use double-sided tape can be attached to the original LCD display tank, or posted elsewhere * Energy saving, power only 8W. Original four LCD power is generally 24W. Brief installation instructions: If your monitor is a high pressure plate, this pressure plate into a direct replacement driver board like if your monitor is one of the high-voltage power supply board, then: one version of the high-pressure electricity, find 12V (capacitance), then pull swap power supply with a multimeter to find and 12V (capacitance) is connected to the negative originals off, boost board then three lines 12V, ON, GND, 12V 12V positive electrode plate with high pressure booster is integrally connected to the board, GND with negative connected, oN even oN / OFF. it is simply the original high-voltage power supply is disconnected to replace the booster plate at the front end of the original pressure to take power. The following are the installation instructions for reference (for reference only): Easy modification steps: 1, open the metal frame: 2, cut the inner plastic protective frame angle: 3, out of the liquid crystal lamp: 4, insert the LED light bar Note, this modification method is simple, easy to light leakage. But it will destroy the border. Normal method: 1, open to protect the metal frame with a simple conversion step. 2. Remove the LCD glass panel (panel carefully on soft cable, such as careless easy to qualify and broadband) 3. Remove the plastic inner frame and lighthouse (Be careful not to get dirty fouling within the backlight assembly) 4. Remove the inner lamp lighthouse 5, LED light bar affixed inside the lighthouse 6, then restore the original removal steps carefully 7. Replace the glass panels and metal frame test 8, installed lights. Package Includes: 2x LED strips 1x Driver board 1x cable     Le 13-juil.-19 à 04:59:04 Paris, le vendeur a ajouté les informations suivantes:

Specification: LED Strip Size: 540mm x 4mm Driver board size:7x2cm Input:DC 10-30V OutPut:7.5V-9.6V Features: * The product of the original display-specific lights, high brightness, can not look directly * LED particles close, high-density arrangement bright LED SMD imports * Long life, is a display design, the life of 100,000 hours * Easy to install, use double-sided tape can be attached to the original LCD display tank, or posted elsewhere * Energy saving, power only 8W. Original four LCD power is generally 24W. Brief installation instructions: If your monitor is a high pressure plate, this pressure plate into a direct replacement driver board like if your monitor is one of the high-voltage power supply board, then: one version of the high-pressure electricity, find 12V (capacitance), then pull swap power supply with a multimeter to find and 12V (capacitance) is connected to the negative originals off, boost board then three lines 12V, ON, GND, 12V 12V positive electrode plate with high pressure booster is integrally connected to the board, GND with negative connected, oN even oN / OFF. it is simply the original high-voltage power supply is disconnected to replace the booster plate at the front end of the original pressure to take power. The following are the installation instructions for reference (for reference only): Easy modification steps: 1, open the metal frame: 2, cut the inner plastic protective frame angle: 3, out of the liquid crystal lamp: 4, insert the LED light bar Note, this modification method is simple, easy to light leakage. But it will destroy the border. Normal method: 1, open to protect the metal frame with a simple conversion step. 2. Remove the LCD glass panel (panel carefully on soft cable, such as careless easy to qualify and broadband) 3. Remove the plastic inner frame and lighthouse (Be careful not to get dirty fouling within the backlight assembly) 4. Remove the inner lamp lighthouse 5, LED light bar affixed inside the lighthouse 6, then restore the original removal steps carefully 7. Replace the glass panels and metal frame test 8, installed lights. Package Includes: 2x LED strips 1x Driver board 1x cable Le 19-août-19 à 13:43:11 Paris, le vendeur a ajouté les informations suivantes:

  Specification: LED Strip Size: 540mm x 4mm Driver board size:7x2cm Input:DC 10-30V OutPut:7.5V-9.6V Features: * The product of the original display-specific lights, high brightness, can not look directly * LED particles close, high-density arrangement bright LED SMD imports * Long life, is a display design, the life of 100,000 hours * Easy to install, use double-sided tape can be attached to the original LCD display tank, or posted elsewhere * Energy saving, power only 8W. Original four LCD power is generally 24W. Brief installation instructions: If your monitor is a high pressure plate, this pressure plate into a direct replacement driver board like if your monitor is one of the high-voltage power supply board, then: one version of the high-pressure electricity, find 12V (capacitance), then pull swap power supply with a multimeter to find and 12V (capacitance) is connected to the negative originals off, boost board then three lines 12V, ON, GND, 12V 12V positive electrode plate with high pressure booster is integrally connected to the board, GND with negative connected, oN even oN / OFF. it is simply the original high-voltage power supply is disconnected to replace the booster plate at the front end of the original pressure to take power. The following are the installation instructions for reference (for reference only): Easy modification steps: 1, open the metal frame: 2, cut the inner plastic protective frame angle: 3, out of the liquid crystal lamp: 4, insert the LED light bar Note, this modification method is simple, easy to light leakage. But it will destroy the border. Normal method: 1, open to protect the metal frame with a simple conversion step. 2. Remove the LCD glass panel (panel carefully on soft cable, such as careless easy to qualify and broadband) 3. Remove the plastic inner frame and lighthouse (Be careful not to get dirty fouling within the backlight assembly) 4. Remove the inner lamp lighthouse 5, LED light bar affixed inside the lighthouse 6, then restore the original removal steps carefully 7. Replace the glass panels and metal frame test 8, installed lights. Package Includes: 2x LED strips 1x Driver board 1x cable -Nous acceptons seulement le paiement Paypal. - acheteurs   internationaux - veuillez   noter: a) les taxes et frais d'importation ne sont pas inclus dans le prix de l'article ou les frais d'expédition.  Ces   charges   sont   la   responsabilité   de   l' acheteur. b) Veuillez vérifier auprès du Bureau de douane de votre pays pour déterminer ce que ces coûts supplémentaires seront avant d'enchérir/acheter. * Nous ne pouvons pas expédier aux cases postales ou aux adresses d'APO/FPO Merci!     Le 23-août-19 à 18:22:31 Paris, le vendeur a ajouté les informations suivantes:

540mm LED Backlight Strip Kit For 24" inch Update CCFL LCD Screen To MonitWFFR Specification: LED Strip Size: 540mm x 4mm Driver board size:7x2cm Input:DC 10-30V OutPut:7.5V-9.6V Features: * The product of the original display-specific lights, high brightness, can not look directly * LED particles close, high-density arrangement bright LED SMD imports * Long life, is a display design, the life of 100,000 hours * Easy to install, use double-sided tape can be attached to the original LCD display tank, or posted elsewhere * Energy saving, power only 8W. Original four LCD power is generally 24W. Brief installation instructions: If your monitor is a high pressure plate, this pressure plate into a direct replacement driver board like if your monitor is one of the high-voltage power supply board, then: one version of the high-pressure electricity, find 12V (capacitance), then pull swap power supply with a multimeter to find and 12V (capacitance) is connected to the negative originals off, boost board then three lines 12V, ON, GND, 12V 12V positive electrode plate with high pressure booster is integrally connected to the board, GND with negative connected, oN even oN / OFF. it is simply the original high-voltage power supply is disconnected to replace the booster plate at the front end of the original pressure to take power. The following are the installation instructions for reference (for reference only): Easy modification steps: 1, open the metal frame: 2, cut the inner plastic protective frame angle: 3, out of the liquid crystal lamp: 4, insert the LED light bar Note, this modification method is simple, easy to light leakage. But it will destroy the border. Normal method: 1, open to protect the metal frame with a simple conversion step. 2. Remove the LCD glass panel (panel carefully on soft cable, such as careless easy to qualify and broadband) 3. Remove the plastic inner frame and lighthouse (Be careful not to get dirty fouling within the backlight assembly) 4. Remove the inner lamp lighthouse 5, LED light bar affixed inside the lighthouse 6, then restore the original removal steps carefully 7. Replace the glass panels and metal frame test 8, installed lights. Package Includes: 2x LED strips 1x Driver board 1x cable Le 22-août-19 à 10:39:35 Paris, le vendeur a ajouté les informations suivantes:

Specification: LED Strip Size: 540mm x 4mm Driver board size:7x2cm Input:DC 10-30V OutPut:7.5V-9.6V Features: * The product of the original display-specific lights, high brightness, can not look directly * LED particles close, high-density arrangement bright LED SMD imports * Long life, is a display design, the life of 100,000 hours * Easy to install, use double-sided tape can be attached to the original LCD display tank, or posted elsewhere * Energy saving, power only 8W. Original four LCD power is generally 24W. Brief installation instructions: If your monitor is a high pressure plate, this pressure plate into a direct replacement driver board like if your monitor is one of the high-voltage power supply board, then: one version of the high-pressure electricity, find 12V (capacitance), then pull swap power supply with a multimeter to find and 12V (capacitance) is connected to the negative originals off, boost board then three lines 12V, ON, GND, 12V 12V positive electrode plate with high pressure booster is integrally connected to the board, GND with negative connected, oN even oN / OFF. it is simply the original high-voltage power supply is disconnected to replace the booster plate at the front end of the original pressure to take power. The following are the installation instructions for reference (for reference only): Easy modification steps: 1, open the metal frame: 2, cut the inner plastic protective frame angle: 3, out of the liquid crystal lamp: 4, insert the LED light bar Note, this modification method is simple, easy to light leakage. But it will destroy the border. Normal method: 1, open to protect the metal frame with a simple conversion step. 2. Remove the LCD glass panel (panel carefully on soft cable, such as careless easy to qualify and broadband) 3. Remove the plastic inner frame and lighthouse (Be careful not to get dirty fouling within the backlight assembly) 4. Remove the inner lamp lighthouse 5, LED light bar affixed inside the lighthouse 6, then restore the original removal steps carefully 7. Replace the glass panels and metal frame test 8, installed lights. Package Includes: 2x LED strips 1x Driver board 1x cable Le 03-sept.-19 à 19:13:32 Paris, le vendeur a ajouté les informations suivantes:

Etat: Neuf Marque: Acer Modèle:  B247WBMIPRX  Garantie: 90jours Type d'affichage  :   Écran LCD à rétroéclairage LED / matrice active TFT Classe énergétique  :   Classe A+ Consommation d'énergie annuelle  :   25 kWh Consommation électrique en mode marche  :   17 Watt Taille de la diagonale  :   24" Type de panneau  :   IPS Facteur de forme  :   16:10 Résolution Native  :   WUXGA 1920 x 1200 à 60 Hz Luminosité  :   300 cd/m² Rapport de contraste  :   1000:1 / 100000000:1 (dynamique) Prise en charge des couleurs  :   16,7 millions de couleurs Temps de réponse  :   4 ms (gris à gris) Angle de visualisation horizontale  :   178 Angle de visualisation verticale  :   178 Revêtement de l'écran  :   Anti-éblouissement Technologie de rétroéclairage  :   Rétroéclairage par LED FonctionsErgoStand, Acer Adaptive Contrast Management (ACM), High Frame Rate Control (Hi-FRC), ComfyView,  Zero Frame, technologie Flicker-Less, technologie de réglage de la luminosité Low Dimming, Acer VisionCare,  gamma 6 bits, Grand angle de visualisation, technologie Acer BluelightShield, 6-Axis Color Adjustments Dimensions (LxPxH)  :   54.1 cm x 19.3 cm x 49.8 cm - avec support Poids  :   5.58 kg AUDIO Type  :   Haut-parleurs - stéreo Puissance de sortie/canal  :   2 Watt

Etat: Neuf Marque: IIYAMA Modèle: X2474HS-B2 Garantie: 90jours GÉNÉRAL Type d'affichage  :   Écran LCD à rétroéclairage LED / matrice active TFT Classe énergétique  :   Classe B Consommation d'énergie annuelle  :   39 kWh Consommation électrique en mode marche  :   26.8 Watt Taille de la diagonale  :   24" Surface visible  :   23.6" Type de panneau  :   VA Facteur de Forme  :   16:9 Résolution native  :   Full HD (1080p) 1920 x 1080 Densité par pixel  :   0.272 mm Luminosité  :   250 cd/m² Rapport de contraste  :   3000:1 / 80000000:1 (dynamique) Prise en charge des couleurs  :   16,7 Millions de Couleurs Temps de réponse  :   4 ms Fréquence de réactualisation verticale  :   55 - 75 Hz Fréquence de réactualisation horizontale  :   30 - 80 kHz Angle de visualisation horizontale  :   +89 / -89 Angle de visualisation verticale  :   +89 / -89 Revêtement de l'écran  :   Mat Technologie de rétroéclairage  :   Rétroéclairage par LED Langages OSD  :   Tchèque, anglais, allemand, français, italien, polonais,  russe, espagnol, hollandais, japonais, chinois Type de lunette  :   Élevé Fonctions  :   HDCP, Eco-Mode, gamme de couleurs étendue NTSC de 72 %, High Frame Rate Control (Hi-FRC), Advanced Contrast Ratio (ACR), gamme étendue de couleurs sRGB 99 %, technologie Flicker Free, réduction de la lumière bleue Couleur  :   Noir Dimensions (LxPxH)  :   54.6 cm x 19.95 cm x 40.3 cm Poids  :   3.7 kg AUDIO Type  :   Haut-parleurs - stéreo Puissance de sortie/canal  :   2 Watt

Etat: Neuf Marque: IIYAMA Modèle: E2483HSU-B5 Garantie: 90jours GÉNÉRAL Type d'affichage  :   Écran LCD à rétroéclairage LED / matrice active TFT Classe énergétique  :   Classe A+ Consommation d'énergie annuelle  :   28 kWh Taille de la diagonale  :   24" Surface visible  :   24" Appareils Intégrés  :   Concentrateur USB 2.0 Type de panneau  :   TN Facteur de Forme  :   16:9 Résolution Native  :   Full HD (1080p) 1920 x 1080 à 75 Hz Densité par pixel  :   0.277 mm Luminosité  :   250 cd/m² Rapport de contraste  :   1000:1 / 80000000:1 (dynamique) Prise en charge des couleurs  :   16,7 Millions de Couleurs Temps de Réponse  :   1 ms Fréquence de réactualisation verticale  :   56 - 75 Hz Fréquence de réactualisation horizontale  :   31 - 85 kHz Angle de visualisation horizontale  :   +85 / -85 Angle de visualisation verticale  :   +80 / -80 Revêtement de l'écran  :   Mat Technologie de rétroéclairage  :   Rétroéclairage par LED Langages OSD  :   Tchèque, anglais, allemand, français, italien, polonais, russe, espagnol, hollandais, japonais Type de lunette  :   Élevé Fonctions  :   HDCP, gamme de couleurs étendue NTSC de 72 %, High Frame Rate Control (Hi-FRC), Advanced Contrast Ratio (ACR), gamme étendue de couleurs sRGB 99 %, technologie Flicker Free, réduction de la lumière bleue Couleur  :   Noir Dimensions (LxPxH)  :   56.5 cm x 18.7 cm x 41.4 cm Poids  :   3.4 kg AUDIO Type  :   Haut-parleurs - stéreo Puissance de sortie/canal  :   1 Watt

Etat: Neuf Marque: IIYAMA Modèle: B2483HSU-W5 Garantie: 90jours GÉNÉRAL Type d'affichage  :   Écran LCD à rétroéclairage LED / matrice active TFT Classe énergétique  :   Classe A+ Consommation d'énergie annuelle  :   28 kWh Consommation électrique en mode marche  :   18 Watt Taille de la diagonale  :   24" Surface visible  :   24" Appareils Intégrés  :   Concentrateur USB 2.0 Type de panneau  :   TN Facteur de forme  :   16:9 Résolution native  :   Full HD (1080p) 1920 x 1080 à 60 Hz Densité par pixel  :   0.277 mm Luminosité  :   250 cd/m² Rapport de contraste  :   1000:1 / 80000000:1 (dynamique) Prise en charge des couleurs  :   16,7 millions de couleurs Temps de réponse  :   1 ms Fréquence de réactualisation verticale  :   56 - 75 Hz Fréquence de réactualisation horizontale  :   31 - 85 kHz Angle de visualisation horizontale  :   +85 / -85 Angle de visualisation verticale  :   +80 / -80 Revêtement de l'écran  :   Mat Technologie de rétroéclairage  :   Rétroéclairage par LED Langages OSD  :   Tchèque, anglais, allemand, français, italien, polonais, russe, espagnol, hollandais, japonais Type de lunette  :   Élevé Fonctions  :   HDCP, gamme de couleurs étendue NTSC de 72 %, High Frame Rate Control (Hi-FRC), Advanced Contrast Ratio (ACR), gamme étendue de couleurs sRGB 99 %, technologie Flicker Free, réduction de la lumière  bleue Couleur  :  B lanc Dimensions (LxPxH)  :   56.55 cm x 21 cm x 37.55 cm Poids  :   5.1 kg AUDIO Type  :   Haut-parleurs - stéreo Puissance de sortie/canal  :   1 watt MÉCANIQUE Réglages de la position de l'écran  :   Hauteur, pivot (rotation), pivotant, inclinaison Angle d'inclinaison  :   -5/+22 Angle de pivotement  :   90 Angle de rotation  :   90 Réglage de la hauteur  :   130 mm Interface de montage VESA  :   100 x 100 mm

Etat: Neuf Marque: IIYAMA Modèle:  B2483HSU-B5 Garantie: 90jours GÉNÉRAL Type d'affichage  :   Écran LCD à rétroéclairage LED / matrice active TFT Classe énergétique  :   Classe A+ Consommation d'énergie annuelle  :   28 kWh Consommation électrique en mode marche  :   18 Watt Taille de la diagonale  :   24" Surface visible  :   24" Appareils Intégrés  :   Concentrateur USB 2.0 Type de panneau  :   TN Facteur de Forme  :   16:9 Résolution Native  :   Full HD (1080p) 1920 x 1080 à 60 Hz Densité par pixel  :   0.277 mm Luminosité  :   250 cd/m² Rapport de contraste  :   1000:1 / 80000000:1 (dynamique) Prise en charge des couleurs  :   16,7 Millions de Couleurs Temps de Réponse  :   1 ms Fréquence de réactualisation verticale  :   56 - 75 Hz Fréquence de réactualisation horizontale  :   31 - 85 kHz Angle de visualisation horizontale  :   +85 / -85 Angle de visualisation verticale  :   +80 / -80 Revêtement de l'écran  :   Mat Technologie de rétroéclairage  :   Rétroéclairage par LED Langages OSD  :   Tchèque, anglais, allemand, français, italien, polonais, russe, espagnol, hollandais, japonais Type de lunette  :   Élevé Fonctions  :   HDCP, gamme de couleurs étendue NTSC de 72 %, High Frame Rate Control (Hi-FRC), Advanced Contrast Ratio (ACR), gamme étendue de couleurs sRGB 99 %, technologie Flicker Free, réduction de la lumière bleue Couleur  :   Noir mat Dimensions (LxPxH)  :   56.55 cm x 21 cm x 37.55 cm Poids  :   5.1 kg AUDIO Type  :   Haut-parleurs - stéreo Puissance de sortie/canal  :   1 watt MÉCANIQUE Réglages de la position de l'écran  :   Hauteur, pivot (rotation), pivotant, inclinaison Angle d'inclinaison  :   -5/+22 Angle de pivotement  :   90 Angle de rotation  :   90 Réglage de la hauteur  :   130 mm Interface de montage VESA  :   100 x 100 mm

Etat: Neuf Marque: IIYAMA Modèle: XUB2294HSU-B1 Garantie: 90jours Type d'affichage  :   Écran LCD à rétroéclairage LED / matrice active TFT Classe énergétique  :   Classe A+ Consommation d'énergie annuelle  :   23 kWh Consommation électrique en mode marche  :   16 Watt Taille de la diagonale  :   22" Surface visible  :   21.5" Appareils Intégrés  :   Concentrateur USB 2.0 Type de panneau  :   VA Facteur de forme  :   16:9 Résolution Native  :   Full HD (1080p) 1920 x 1080 à 75 Hz Densité par pixel  :   0.248 mm Luminosité  :   250 cd/m² Rapport de contraste  :   3000:1 / 80000000:1 (dynamique) Prise en charge des couleurs  :   16,7 millions de couleurs Temps de réponse  :   4 ms Fréquence de réactualisation verticale  :   55 - 75 Hz Fréquence de réactualisation horizontale  :   30 - 83 kHz Angle de visualisation horizontale  :   +89 / -89 Angle de visualisation verticale  :   +89 / -89 Revêtement de l'écran  :   Mat Technologie de rétroéclairage  :   Rétroéclairage par LED Langages OSD  :   Tchèque, anglais, allemand, français, italien, polonais,  russe, espagnol, hollandais, japonais Type de lunette  :   Avant plat Fonctions  :   Design ultra fin, HDCP, Eco-Mode, gamme de couleurs  étendue NTSC de 72 %, High Frame Rate Control (Hi-FRC), Advanced  Contrast Ratio (ACR), gamme étendue de couleurs sRGB 99 %,  technologie Flicker Free, réduction de la lumière bleue, i-Style Color,  gamma 8 bits Couleur  :   Noir mat Dimensions (LxPxH)  :   48.85 cm x 21 cm x 35.2 cm Poids  :   4.7 kg AUDIO Type  :   Haut-parleurs - stéreo Puissance de sortie/canal  :   1 Watt

Etat: Neuf Marque: IIYAMA Modèle:  XUB2294HSU-W1 Garantie: 90jours GÉNÉRAL Type d'affichage Écran LCD à rétroéclairage LED / matrice active TFT Classe énergétique Classe A+ Consommation d'énergie annuelle 23 kWh Consommation électrique en mode marche 16 Watt Taille de la diagonale 22" Surface visible 21.5" Appareils intégrés Concentrateur USB 2.0 Type de panneau VA Facteur de Forme 16:9 Résolution native Full HD (1080p) 1920 x 1080 à 75 Hz Densité par pixel 0.248 mm Luminosité 250 cd/m² Rapport de contraste 3000:1 / 80000000:1 (dynamique) Prise en charge des couleurs 16,7 millions de couleurs Temps de réponse 4 ms Fréquence de réactualisation verticale 55 - 75 Hz Fréquence de réactualisation horizontale 30 - 83 kHz Angle de visualisation horizontale +89 / -89 Angle de visualisation verticale +89 / -89 Revêtement de l'écran Mat Technologie de rétroéclairage Rétroéclairage par LED Langages OSD Tchèque, anglais, allemand, français, italien, polonais, russe, espagnol, hollandais, japonais Type de lunette Avant plat Fonctions Design ultra fin, HDCP, Eco-Mode, gamme de couleurs étendue NTSC de 72 %, High Frame Rate Control (Hi-FRC), Advanced Contrast Ratio (ACR), gamme étendue de couleurs sRGB 99 %, technologie Flicker Free, réduction de la lumière bleue, i-Style Color, gamma 8 bits Couleur Blanc mat Dimensions (LxPxH) 48.85 cm x 21 cm x 35.2 cm Poids 4.7 kg AUDIO Type Haut-parleurs - stéreo Puissance de sortie/canal 1 Watt CONNECTIVITÉ Interfaces Interfaces MÉCANIQUE Réglages de la position de l'écran Hauteur, pivot (rotation), pivotant, inclinaison Angle d'inclinaison -5/+22 Angle de pivotement 90 Angle de rotation 90 Réglage de la hauteur 130 mm Interface de montage VESA 100 x 100 mm DIVERS Caractéristiques Fente de verrouillage de sécurité (câble de verrouillage vendu séparément) Câbles inclus 1 x câble HDMI Normes de conformité TUV GS, DDC-2B, PSE Mark, REACH, VCCI Class B, CU, REACH SvHC Type de logement de sécurité Serrure de sécurité Kensington

Etat: Neuf Marque: IIYAMA Modèle: XU2294HSU-B1 Garantie: 90jours GÉNÉRAL Type d'affichage Écran LCD à rétroéclairage LED / matrice active TFT Classe énergétique Classe A+ Consommation d'énergie annuelle 23 kWh Consommation électrique en mode marche 16 Watt Taille de la diagonale 22" Surface visible 21.5" Appareils Intégrés Concentrateur USB 2.0 Type de panneau VA Facteur de Forme 16:9 Résolution Native Full HD (1080p) 1920 x 1080 (DisplayPort: 75 Hz, VGA: 60 Hz, HDMI: 75 Hz) Densité par pixel 0.248 mm Luminosité 250 cd/m² Rapport de contraste 3000:1 / 80000000:1 (dynamique) Prise en charge des couleurs 16,7 millions de couleurs Temps de réponse 4 ms Fréquence de réactualisation verticale 55 - 75 Hz Fréquence de réactualisation horizontale 30 - 85 kHz Angle de visualisation horizontale +89 / -89 Angle de visualisation verticale +89 / -89 Revêtement de l'écran Mat Technologie de rétroéclairage Rétroéclairage par LED Langages OSD Tchèque, anglais, allemand, français, italien, polonais, russe, espagnol, hollandais, japonais Type de lunette Avant plat Fonctions Design ultra fin, HDCP, Eco-Mode, gamme de couleurs étendue NTSC de 72 %, High Frame Rate Control (Hi-FRC), Advanced Contrast Ratio (ACR), gamme étendue de couleurs sRGB 99 %, technologie Flicker Free, réduction de la lumière bleue, i-Style Color, gamma 8 bits Couleur Noir mat Dimensions (LxPxH) 48.85 cm x 18.7 cm x 37.6 cm - avec support Poids 3 kg AUDIO Type Haut-parleurs - stéreo Puissance de sortie/canal 1 Watt CONNECTIVITÉ Interfaces Interfaces MÉCANIQUE Réglages de la position de l'écran Inclinaison Angle d'inclinaison -5/+22 Interface de montage VESA 100 x 100 mm DIVERS Caractéristiques Fente de verrouillage de sécurité (câble de verrouillage vendu séparément) Câbles inclus 1 x câble HDMI Normes de conformité TUV GS, DDC-2B, PSE Mark, REACH, VCCI Class B, CU, REACH SvHC Type de logement de sécurité Serrure de sécurité Kensington

Etat: Neuf Marque: IIYAMA Modèle: XU2292HS-B1 Garantie: 90jours Type d'affichage Écran LCD à rétroéclairage LED / matrice active TFT Classe énergétique Classe A Consommation d'énergie annuelle 24 kWh Consommation électrique en mode marche 16.5 Watt Taille de la diagonale 22" Surface visible 21.5" Appareils Intégrés Concentrateur USB 2.0 Type de panneau IPS Facteur de forme 16:9 Résolution Native Full HD (1080p) 1920 x 1080 (DisplayPort: 75 Hz, VGA: 60 Hz, HDMI: 75 Hz) Densité par pixel 0.248 mm Luminosité 250 cd/m² Rapport de contraste 1000:1 / 80000000:1 (dynamique) Prise en charge des couleurs 16,7 millions de couleurs Temps de Réponse 4 ms Fréquence de réactualisation verticale 55 - 75 Hz Fréquence de réactualisation horizontale 30 - 85 kHz Angle de visualisation horizontale +89 / -89 Angle de visualisation verticale +89 / -89 Revêtement de l'écran Mat Technologie de rétroéclairage Rétroéclairage par LED Langages OSD Tchèque, anglais, allemand, français, italien, polonais, russe, espagnol, hollandais, japonais Type de lunette Avant plat Fonctions Design ultra fin, HDCP, Eco-Mode, gamme de couleurs étendue NTSC de 72 %, High Frame Rate Control (Hi-FRC), Advanced Contrast Ratio (ACR), gamme étendue de couleurs sRGB 99 %, technologie Flicker Free, réduction de la lumière bleue, i-Style Color, gamma 8 bits Couleur Noir mat Dimensions (LxPxH) 48.85 cm x 18.7 cm x 37.6 cm Poids 3.2 kg AUDIO Type Haut-parleurs - stéreo Puissance de sortie/canal 1 watt CONNECTIVITÉ Interfaces Interfaces MÉCANIQUE Réglages de la position de l'écran Inclinaison Angle d'inclinaison -5/+22 Interface de montage VESA 100 x 100 mm DIVERS Caractéristiques Fente de verrouillage de sécurité (câble de verrouillage vendu séparément) Câbles inclus 1 x câble HDMI Normes de conformité TUV GS, DDC-2B, PSE Mark, REACH, VCCI Class B, CU, REACH SvHC Type de logement de sécurité Serrure de sécurité Kensington