Power hf

Working 100%, Tx Rx All bands 100w, Perfect conditions. No Filters. Frequency range: 10-160 m + WARC / 50-54 MHz Mode: AM/FM/SSB/CW/RTTY/Packet RF Power output: Max 100 W

HF all bands with all Xtals, Filter CW inclued, Power Cord, beautifull and working perfect !!

Radio Beacon NDB transmitter HF. It has a DDS generator with a step resolution of 1 Hz from 1 to 55 MHz. The final stage (30 W max power) is set to deliver 5 W. It may be set from 3.5 to 15 MHz (may be modified for 30 Mhz operation. The power supply (120 W) works from 100 to 280 Vac and it’s built in. No fans, no noise. The RF stage an oversized heatsink for continuous operation. The radio beacon has a directional beacon to indicate the forward and reflected power. The ID and the Morse code text may be easily reprogrammed, as well as the keying speed and the pause duration just connecting a PC via USB port using a simple code (provided). Very good stability in power and amplitude. For any further information you are welcome to ask !

Description: MINIWHIP VLF LF HF ACTIVE ANTENNA.This is known PA0NHC newest design of MiniWhip Antenna. I have redesigned and built it on SMD components but the circuit diagram itself stayed the same as it had been described on his web page in open source. This sale includes the MiniWhip and Power Splitter assembled and tested boards. They go with its circuit diagrams and part list specification. No cables or connectors are included. This new version of PA0NHC MiniWhip Antenna has these features.New version, using modern BF998 and BCX54 semi conductors.Real class A circuitry, clean reception without IMD.One coax connection.Broadband R/C coupling to the receiver, no transformer For best signal-to-noise ratio:install the Miniwhip onto a well grounded mast.connect "GND" of the Miniwhip PCB to that mast.place HI-Ui ferrite cores (Ui bwtween 5000 and 10.000) on the beginning and end of all cables to block cable noise currents. Specifications: Frequency range: 10 KHz - 30 MHz Power: 12 - 15 volts at 150 mA Second order output intercept point: Greater than + 70 dBm Third order output intercept point: Greater than + 30 dBm Maximum output power: in excess of - 15 dBm PCB Size: Length (mm): As the picture show Connector: BNC Feed line: 50 - 100 ohm coaxial cable up to 100 meter long T o note please: Each antenna performs as good as its installation permits it to. Any active antenna is not working good inside the house! It should be mounted OUTSIDE and as high as possible. Place this MiniWhip antenna PCB inside suitable enclosure of your choise and mount outside the house. Probably for the enclosure you can use a piece of the PVC tube which available in varios diameters in a local store. Do not use metal enclosure! It wont work there! For max. sensitivity: this antenna should be positioned as high and free from meta Package include: 1Set Board Note:   The color might be a little different from the actual product due to color display of different monitors.  Please allow 1-3 cm error. Le 11-mars-20 à 13:30:27 Paris, le vendeur a ajouté les informations suivantes:

Description: MINIWHIP VLF LF HF ACTIVE ANTENNA.This is known PA0NHC newest design of MiniWhip Antenna. I have redesigned and built it on SMD components but the circuit diagram itself stayed the same as it had been described on his web page in open source. This sale includes the MiniWhip and Power Splitter assembled and tested boards. They go with its circuit diagrams and part list specification. No cables or connectors are included. This new version of PA0NHC MiniWhip Antenna has these features.New version, using modern BF998 and BCX54 semi conductors.Real class A circuitry, clean reception without IMD.One coax connection.Broadband R/C coupling to the receiver, no transformer For best signal-to-noise ratio:install the Miniwhip onto a well grounded mast.connect "GND" of the Miniwhip PCB to that mast.place HI-Ui ferrite cores (Ui bwtween 5000 and 10.000) on the beginning and end of all cables to block cable noise currents. Specifications: Frequency range: 10 KHz - 30 MHz Power: 12 - 15 volts at 150 mA Second order output intercept point: Greater than + 70 dBm Third order output intercept point: Greater than + 30 dBm Maximum output power: in excess of - 15 dBm PCB Size: Length (mm): As the picture show Connector: BNC Feed line: 50 - 100 ohm coaxial cable up to 100 meter long T o note please: Each antenna performs as good as its installation permits it to. Any active antenna is not working good inside the house! It should be mounted OUTSIDE and as high as possible. Place this MiniWhip antenna PCB inside suitable enclosure of your choise and mount outside the house. Probably for the enclosure you can use a piece of the PVC tube which available in varios diameters in a local store. Do not use metal enclosure! It wont work there! For max. sensitivity: this antenna should be positioned as high and free from meta Package include: 1Set Board Note:   The color might be a little different from the actual product due to color display of different monitors.  Please allow 1-3 cm error. Le 04-avr.-20 à 15:50:26 Paris, le vendeur a ajouté les informations suivantes:

Xiegu XPA125B 100W HF Power Amplifier + Auto tuner ATU For X5105 X108G G1M G90.  État : Occasion très peu servi Service de livraison : Mondial relay

DR-7800 can be ideally used for HF email, for example, over the Winlink network. Externally, it stands out due to its high-resolution OLED display which, among other things, can be configured for waterfall and spectral views. Thanks to its reliability and low power consumption of 3 W, the modem is also well-suited for distress radio communications and other applications under severe conditions.   Modes: PACTOR-4, PACTOR-3, PACTOR-2, PACTOR-1 Weather-FAX (Receive) RTTY NAVTEX (Receive) Packet Radio 1k2, Packet Radio 9k6, Robust PR PSK31 DR-7800 Pactor controller: GPS decoder Processor: Quadcore-DSP by Freescale, 6400 MIPS, 64 Bit Connections: USB GPS antenna (RS232- and TTL) 2 x radio AF/PTT (Main, Aux, confi gurable - PTC-II compatible or symmetrical, opt. dual-port operation) 1 x radio-remote control (all usual transceiver types) microphone input loudspeaker output (2 W) Audio level / imp.: Input: max 5.5V p-p, 15kΩ, output: max. 9V p-p, 300Ω Display: 256 x 64 pixel OLED, blue, high contrast, excellent readability, no viewing angle problems, display of spectrum and much more Power supply: 10 - 26 V 400 mA (max at 10 V input) Weight / size: 770 g, 172 x 43 x 205 mm (width, height and depth) package contents: 1 MODEM DR-7800 1 USB cable 1 DIN 8 PIN cable for ICOM transceiver (wires need to be soldered on the other side) 1 DIN 13 PIN cable for ICOM tranceive r (wires need to be soldered on the other side) 1 Installation guide 1 CD-ROM New, open but never used ! Perfect for sailor, navigator or radioamateur ! Pay attention: no shipping outside Europe

Amplifier HF 1200 W 8 X MRF151 With Heatsink for HAM Radio Bands. The pallet has a massive copper plate of 5 mm. It is fixed to the aluminum heatsink of 3 kg. Super robust construction. The pallet requires a 50 Vdc 38 A power supply. The enable input accepts from 5 to 24 Vdc, 300 mA. The pallet has 8 trimmer for biasing adjust. Each mosfet has its current measurement output. On the PCB the current values table is clearly marched on the components side. The bias has been already set, so the amplifier is ready for use. The amplifier is tested and requires a drive power of 20 W max. Just the copper plate and the heatsink has a very good value. For shipping costs to the countries non specified in the bid, please ask for a quotation. The item is quite heavy.

Rx HF 0-30 Mhz (117vlt) GENERAL Type: HF receiver Frequency range: 10-80 m in seven bands 80 m: 3.5-4.0 MHz 40 m: 7.0-7.5 MHz 20 m: 14.0-14.5 MHz 15 m: 21.0-21.5 MHz 10 m: 28.0-28.5 MHz 10 m: 28.5-29.1 MHz 10 m: 29.1-29.7 MHz plus WWV on 51 MHz Tuning steps: Continuous Mode: AM/SSB/CW Channels/memory management: No Power supply: Mains: 110-120 VAC

Rx Kenwood R599 HF. État : "Occasion"                        ONLY CHROME VERSION AVAIBLE !!! 0-30 Mhz Ts Modes + Module VHF (Option) TBE de fonctionnement et de présentation Type: HF receiver Frequency range: 10-160 m + CB (2 m & 6 m options) Tuning steps: Continuous Mode: AM/FM/SSB/CW Channels/memory management: No Power supply: 13.8 VDC or mains

Sloper HF 1/4 onde 5 MHz. Longueur 13,31 m. Isolateur avec connecteur SO-239, fil de cuivre 1.5 mm² sous gaine isolante avec isolateurs aux extrémités. Puissance maximale: 1500 W, poids: 0,4 kg. NB: Ce sloper existe également en mono bande pour: 6m (SP-6)  10m (SP-10)  12m (SP-12)  15m (SP-15)  17m (SP-17)  20m (SP-20)  30m (SP-30)  40m (SP-40)  80m (SP-80)  160m (SP-160) Fiche technique Bande de fréquences - Bands: 5 Mhz Longueur des éléments - Elements length: 13,31m Diamètre des éléments - Elements diameter: 1,5mm² Puissance admissible - Maximum power: 1500w Impédance - Impedance: 50 ohms Connecteur - Connector: SO-239 (PL) Poids - Weight: 0,4 kg

Dipôle HF 1/2 onde 5 MHz. Longueur  2 x 13,33 m. Isolateur central avec connecteur SO-239, fil de cuivre 1.5 mm² sous gaine isolante avec isolateurs aux extrémités. Puissance maximale: 1500 W, gain: 2,15 dBi, poids: 0,5 kg. NB: Ce dipôle existe également en mono bande pour: 6m (DP-6)  10m (DP-10)  12m (DP-12)  15m (DP-15)  17m (DP-17)  20m (DP-20)  30m (DP-30)  40m (DP-40)  80m (DP-80)  160m (DP-160) Fiche technique Bande de fréquences - Bands: 5 Mhz Longueur des éléments - Elements length: 2 x 13,33m Diamètre des éléments - Elements diameter: 1,5mm² Gain: 2,15 dBi Puissance admissible - Maximum power: 1500w Impédance - Impedance: 50 ohms Connecteur - Connector: SO-239 (PL) Poids - Weight: 0,5 kg

Dipôle HF 1/2 onde 27 MHz. Longueur  2 x 2,64 m. Isolateur central avec connecteur SO-239, fil de cuivre 1.5 mm² sous gaine isolante avec isolateurs aux extrémités. Puissance maximale: 1500 W, gain: 2,15 dBi, poids: 0,4 kg. Fiche technique Bande de fréquences - Bands: 27 Mhz Longueur des éléments - Elements length: 2 x 2,64m Diamètre des éléments - Elements diameter: 1,5mm² Gain: 2,15 dBi Puissance admissible - Maximum power: 1500w Impédance - Impedance: 50 ohms Connecteur - Connector: SO-239 (PL) Poids - Weight: 0,4 kg

Sloper HF 1/4 onde 27 MHz. Longueur 2,50 m. Isolateur avec connecteur SO-239, fil de cuivre 1.5 mm² sous gaine isolante avec isolateurs aux extrémités. Puissance maximale: 1500 W, poids: 0,3 kg. Fiche technique Bande de fréquences - Bands: 27 Mhz Longueur des éléments - Elements length: 2,50m Diamètre des éléments - Elements diameter: 1,5mm² Puissance admissible - Maximum power: 1500w Impédance - Impedance: 50 ohms Connecteur - Connector: SO-239 (PL) Poids - Weight: 0,3 kg

Neuf en boite DIAMOND - SX-100 - SWR mètre / puissance de 1,6 à 60 MHz 30/300/3000 Watt Référence SX-100 État: Neuf SWR mètre / PWR mètre - HF / 6M  (1,6 à 60 MHz - 30/300/3000 Watt) envoi rapide

 . Direct from an estate sale of a ham radio operator/collector - all of his vintage gear is in beautiful shape and a nice mix of equipment - including a MINT IN THE BOX Yaesu MD-1B8 Desk Microphone. Please view my other auctions. I will be listing radio gear weekly. This auction is for a beautiful, working YAESU FRG-7700 AM/SSB-CW SHORTWAVE HF RECEIVER. Absolutely PERFECT FRONT PANEL - all controls, lamps and fluorescent digital display operate as designed - all original control knobs with polished silver brights, all control lettering perfect. Steel cabinet looks great, has not dents or dings, only a few light, age-related scratches. Receiver is super clean inside and out. Tested, all bands engage, all modes engage (except FM) - tuning is smooth, selectivity and sensitivity is excellent - very loud audio with a nice, useful Tone control. This is a full sized "real radio" - no tiny confusing drop down sub menus menus - controls are solid and full size - has the feel of a classic communications receiver and is built to last. Comes with AC power cable, Operating Manual and Service Manual is available for free download on numerous websites.  Here is some additional info:   The Yaesu FRG-7700 is a multi-mode receiver covering 150 kHz to 30 MHz in 1 MHz bands to include all longwave, medium wave (AM) and shortwave frequencies. Modes of reception include LSB/CW, USB, AM and FM. An analog dial supplements the 1 kHz yellow LED digital display. The built in clock-timer includes remote activation terminals on the rear panel. Convenience features include:  Variable RF Attenuator, S-Meter, Dimmer, AGC Fast/Slow, Squelch, Tone Control and Noise Blanker. Twelve memories (fine tunable with M FINE knob), are available if the optional MU7700 memory unit is installed on the rear panel. The rear panel has dual antenna inputs, remote timer activation jacks and speaker output.  The detailed well lit photos are a perfect representation of the condition. Enlarge them and ask questions before bidding please. All equipment is sold as vintage electronics and may need repairs and parts replaced over time - SOLD AS IS - NO RETURNS.   US BUYERS PAYS FEDEX SHIPPING ONLY CONTINENTAL USA WE DO NOT SHIP TO P.O. BOXES We strive for 100% customer satisfaction. Incredible customer service along with a fun auction experience is our number one goal! I have successfully shipped delicate vintage radios and electronics for over 20 years - all over the globe. I double-box, bubble wrap and use plenty of padding...at no extra charge! This is a real auction....99 Cents OPENING BID...NO RESERVE...NO REGRETS! PLEASE VIEW MY OTHER AUCTIONS FOR MORE QUALITY VINTAGE ELECTRONICS

Bandpass filter for HF bands. État : "Occasion" Set of 2 bandpass filters. Each filters covers the following bands: 10M, 15M, 20M, 40M, 80M, 160M. Filters are built in a metal case with BNC connectors. They are provided with a remote control and built-in power supply. W3LPL design.

Codan HF transceiver 9780 you can with front keybord programming 15 channel at you choose to 3 to 30 Mhz lsb or usb you are also listen in free tune in reception 250 khz to 30 Mhz power output 120 watts

Codan HF transceiver 9780 you can with front keybord programming 15 channel at you choose to 3 to 30 Mhz lsb or usb you are also listen in free tune in reception 250 khz to 30 Mhz maximum power output 120 watts

DRAKE TR-7 tranceiver serial:9232 RV-7 External VFO  serial:2815 (value: 100€ included) PS-7 Power Supply  serial:8521 (value: 180€ included) AUX-7 Auxilary board (value: 100€ included) NB-7 Noise blanker (value: 160€ included) FAN-7 Fan (value: 50€ included) 3 Filters 6k, 1.8k, 0.5k (value: 200€ included) + original maintenance manuals PAYPAL ONLY This bundle will be dispatched in 2 card boxes. Remise en mains propres possible sur Nice et sa région (me contacter)

This multimode transceiver covers 160 to 10 meters plus a general coverage receiver. There is a digital display with analog subdial. Other features include PBT, RIT, VOX, meter and NB. Has optional FA7 fan kit on the rear panel. DRAKE TR-7 tranceiver serial:9232 + RV-7 External VFO  serial:2815 (included) + PS-7 Power Supply  serial:8521 (included) + AUX-7 Auxilary board (included) + NB-7 Noise blanker (included) + FAN-7 Fan (included) + 3 Filters 6k, 1.8k, 0.5k (included) + original maintenance manuals This bundle will be dispatched in 2 card boxes. Feel free to contact me OFFER WELCOME PAYPAL ONLY 

Description:    Manual download   Simple and practical PC control software, you can export Touchstone (snp) files for various radio design and simulation software through PC software. The improved frequency algorithm can use the odd harmonic extension of si5351 to support the measurement frequency up to 900MHz. The metal shield is designed to reduce the external interference and improve the measurement accuracy. The 50535-300MHz frequency range of the si5351 direct output provides better than 70dB dynamic. The extended 300M-600MHz band provides better than 60dB of dynamics, and the 600M-900M band is better than 50dB of dynamics.   This is a DIY product that provides perfect vector network measurement capabilities in the size of a credit card. It includes a 2.8-inch touch screen and 500mAh battery, which can be used offline for 2 hours. For longer measurement, please connect external power supply or contact me to make a larger battery version. The TX/RX method can measure the complete S11 and S21 parameters. If you need to obtain S12 and S22, you need to manually replace the transceiver port wiring.           Basic performance:   ● PCB: 54mm x 85.5mm x 11mm (without connectors, switches) ● Measurement frequency: 50KHz ~ 300MHz (50KHz -900MHz, enable extended firmware) ● RF output: -13dbm (maximum -9dbm) ● Measurement range: 70dB (50kHz-300MHz), 60dB (300M-600MHz), 50dB (600M-900MHz) enable extended firmware); ● Port SWR: ● Display: 2.8 inch TFT (320 x240) ● USB interface: USB type-C communication mode: CDC (serial) ● Power: USB 5V 120mA, built-in 300mAh or 500mAh battery, maximum charging current 0.8A ● Number of scanning points: 101 (fixed) ● Display Tracking: 4   ●  Marking: 4   ● Setting Save: 5   ● Measuring S parameters, voltage standing wave ratio, phase, delay, Smith chart...     Package list:   1X NanoVNA host (with 500mAh battery)   1X USB Type-C data cable   Le 04-avr.-20 à 14:27:06 Paris, le vendeur a ajouté les informations suivantes:

Ampli cibi 27MHz AM/BLU 50w ZETAGI B47 Frequency: 26-30MHz Modes: AM/FM/SSB Input power: 1-4W AM 2-8W SSB Output power: 50W AM 100W SSB Alimentation: 13.8v DC Current drain: 6 amps Connecteurs: 2 X SO239 sockets

Sloper raccourci 5 MHz. Longueur 9,33m. Isolateur avec connecteur SO-239, fil de cuivre 1.5 mm² sous gaine isolante avec isolateur à l'extrémité. Puissance maximale: 1500 W, poids: 0,45 kg. NB: Ce sloper raccourci existe également en mono bande pour: 6m (SPR-6)  10m (SPR-10)  12m (SPR-12)  15m (SPR-15)  17m (SPR-17)  20m (SPR-20)  30m (SPR-30)  40m (SPR-40)  80m (SPR-80)  160m (SPR-160) Fiche technique Bande de fréquences - Bands: 5 Mhz Longueur des éléments - Elements length: 9,33m Diamètre des éléments - Elements diameter: 1,5mm² Puissance admissible - Maximum power: 1500w Impédance - Impedance: 50 ohms Connecteur - Connector: SO-239 (PL) Poids - Weight: 0,45 kg

Dipôle raccourci 5 mhz tout neuf. Longueur 2 x 7,62 m. Isolateur central avec connecteur SO-239, fil de cuivre 1.5 mm² sous gaine isolante avec isolateurs aux extrémités. Puissance maximale: 1500 W, gain: 2,15 dBi, poids: 0,7 kg. NB: Ce dipôle existe également en mono bande pour: 6m (DP-6R)  10m (DP-10R)  12m (DP-12R)  15m (DP-15R)  17m (DP-17R)  20m (DP-20R)  30m (DP-30R)  40m (DP-40R)  80m (DP-80R)  160m (DP-160R) Fiche technique Bande de fréquences - Bands: 5 Mhz Longueur des éléments - Elements length: 2 x 7,62m Diamètre des éléments - Elements diameter: 1,5mm² Gain: 2,15 dBi Puissance admissible - Maximum power: 1500w Impédance - Impedance: 50 ohms Connecteur - Connector: SO-239 (PL) Poids - Weight: 0,7 kg

Dipôle raccourci 50 mhz tout neuf. Longueur 2 x 1.10 m. Isolateur central avec connecteur SO-239, fil de cuivre souple 1.5 mm² sous gaine isolante avec isolateurs aux extrémités. Puissance maximale: 1500 W, gain: 2,15 dBi, poids: 0,3 kg. NB: Ce dipôle existe également en mono bande pour: 10m (DP-10R)  12m (DP-12R)  15m (DP-15R)  17m (DP-17R)  20m (DP-20R)  30m (DP-30R)  40m (DP-40R)  60m (DP-60R)  80m (DP-80R) 160m (DP-160R) Fiche technique Bande de fréquences - Bands: 50 Mhz Longueur des éléments - Elements length: 2 x 1,10m Diamètre des éléments - Elements diameter: 1,5mm² Gain: 2,15 dBi Puissance admissible - Maximum power: 1500w Impédance - Impedance: 50 ohms Connecteur - Connector: SO-239 (PL) Poids - Weight: 0,3 kg

Dipôle raccourci 28 mhz tout neuf. Longueur 2 x 1.90 m. Isolateur central avec connecteur SO-239, fil de cuivre souple 1.5 mm² sous gaine isolante avec isolateurs aux extrémités. Puissance maximale: 1500 W, gain: 2,15 dBi, poids: 0,4 kg. NB: Ce dipôle existe également en mono bande pour: 6m (DP-6R)  12m (DP-12R)  15m (DP-15R)  17m (DP-17R)  20m (DP-20R)  30m (DP-30R)  40m (DP-40R)  60m (DP-60R)  80m (DP-80R) 160m (DP-160R) Fiche technique Bande de fréquences - Bands: 28 Mhz Longueur des éléments - Elements length: 2 x 1;90m Diamètre des éléments - Elements diameter: 1,5mm² Gain: 2,15 dBi Puissance admissible - Maximum power: 1500w Impédance - Impedance: 50 ohms Connecteur - Connector: SO-239 (PL) Poids - Weight: 0,4 kg

Dipôle raccourci 24 mhz tout neuf. Longueur 2 x 2.50 m. Isolateur central avec connecteur SO-239, fil de cuivre souple 1.5 mm² sous gaine isolante avec isolateurs aux extrémités. Puissance maximale: 1500 W, gain: 2,15 dBi, poids: 0,5 kg. NB: Ce dipôle existe également en mono bande pour: 6m (DP-6R)  10m (DP-10R)  12m (DP-12R)  15m (DP-15R)  17m (DP-17R)  20m (DP-20R)  30m (DP-30R)  40m (DP-40R)  60m (DP-60R)  80m (DP-80R) 160m (DP-160R) Fiche technique Bande de fréquences - Bands: 24 Mhz Longueur des éléments - Elements length: 2 x 2,50m Diamètre des éléments - Elements diameter: 1,5mm² Gain: 2,15 dBi Puissance admissible - Maximum power: 1500w Impédance - Impedance: 50 ohms Connecteur - Connector: SO-239 (PL) Poids - Weight: 0,5 kg

Dipôle raccourci 21 mhz tout neuf. Longueur 2 x 2.90 m. Isolateur central avec connecteur SO-239, fil de cuivre souple 1.5 mm² sous gaine isolante avec isolateurs aux extrémités. Puissance maximale: 1500 W, gain: 2,15 dBi, poids: 0,5 kg. NB: Ce dipôle existe également en mono bande pour: 6m (DP-6R)  10m (DP-10R)  12m (DP-12R)  17m (DP-17R)  20m (DP-20R)  30m (DP-30R)  40m (DP-40R)  60m (DP-60R)  80m (DP-80R) 160m (DP-160R) Fiche technique Bande de fréquences - Bands: 21 Mhz Longueur des éléments - Elements length: 2 x 2,90m Diamètre des éléments - Elements diameter: 1,5mm² Gain: 2,15 dBi Puissance admissible - Maximum power: 1500w Impédance - Impedance: 50 ohms Connecteur - Connector: SO-239 (PL) Poids - Weight: 0,5 kg

Dipôle raccourci 18 mhz tout neuf. Longueur 2 x 3.10 m. Isolateur central avec connecteur SO-239, fil de cuivre souple 1.5 mm² sous gaine isolante avec isolateurs aux extrémités. Puissance maximale: 1500 W, gain: 2,15 dBi, poids: 0,5 kg. NB: Ce dipôle existe également en mono bande pour: 6m (DP-6R)  10m (DP-10R)  12m (DP-12R)  15m (DP-15R)  20m (DP-20R)  30m (DP-30R)  40m (DP-40R)  60m (DP-60R)  80m (DP-80R) 160m (DP-160R) Fiche technique Bande de fréquences - Bands: 18 Mhz Longueur des éléments - Elements length: 2 x 3,10m Diamètre des éléments - Elements diameter: 1,5mm² Gain: 2,15 dBi Puissance admissible - Maximum power: 1500w Impédance - Impedance: 50 ohms Connecteur - Connector: SO-239 (PL) Poids - Weight: 0,5 kg