Normally use

- - - - - - - - - - - - Product Description After purchasing and receiving the goods, please pay attention to the following items: NOTE: The power must be cut off before the Epson print head is installed, otherwise it will cause the print head’s circuit board to be burned out. 1.When the print head is shipped, it will be coated with a protective liquid. When using it for the first time, wipe the print head before installing it. The protective liquid drops on the chip and where the ink bleeds. And use tissue to gently wipe the protective liquid on the chip (on the copper sheet). Don't use cleaning fluid or eraser. 2.During the regeneration process of the print head, the original ink will be cleaned and the protective liquid will be injected. If there is no protective liquid, printing will not be done when  the pipeline is dry. If the print head can be detected, but color irregularity or blurry is observed, you can continue to add ink to print, print sheets to use up the protection liquid. And then the color can be used to print. 3. If the printing is not clear, press the cleaning button of the machine. And the print head can be cleaned when the ink cartridge is full of ink. If there is no ink to clean the print head, it is easy to be burn out. And you can print clearly after printing a few times. 4. Clean the print head directly on the machine instead using cleaning fluid. If you clean it with cleaning fluid and do not drop the protective fluid, the print head will be completely blocked  and can not be used. 5. Don't use cleaning fluid or water to clean the print head, otherwise the print head will be completely blocked. When replacing the print head, please pay attention to the following items: 1.After receiving the print head, do not use a needle tube to inject water to check if the print head is blocked. It is a useless and dangerous practice. First of all, once the print head gets water and is not dry, and power on the machine, the main board will be burned out, and even the print head will be burned out. 2.The head surface of the print head is very fragile. It must not be touched, and needs to be protected. Its surface is an aluminum sheet, and inside is coated with a crystal oscillator and a very small ink tube. It will be deformed or even broken when touched, and the print head will be scrapped. 3.Be careful when installing the print head, be sure to cut off the power first, and install it in place. After installation, please push gently with your hands. Do not power on after installation, because if the head is not in place, the head will easily break when the machine moves. But your hands can feel, and it is easy to control. 4.When connecting the plug cable, do not be with ink. And make sure to make good contact with the socket and not touch the feet. Otherwise, it will cause the print head to short-circuit and burn. 5.The steel shaft should also be clean and smooth. Use tissue to stick some lubricating oil to wipe it off. Do not directly add oil to the shaft because excess oil will flow to the print head and cause damage. 6.After confirming that the machinery and circuit are normal, it is necessary to check the water circuit. First, check whether the amount of water in the ink cartridge is sufficient or not; second, check whether the small cleaning blade and the ink pump are dirty or not. 7.There will be air in the newly installed print head, so it will not print normally immediately. Only after the air in the print head is completely exhausted can the lines be printed normally. First of all, you can use the machine's cleaning function to perform intermittent cleaning (two cleanings each time,and then two more cleanings after a 30-minute pause). Excessive cleaning for many times will cause ink accumulation in the cleaning pump. It will not only cause color mixing and ink leakage, but also

- - - - - - - - - - - - - - - - - - - - - - - - Product Description After purchasing and receiving the goods, please pay attention to the following items: NOTE: The power must be cut off before the Epson print head is installed, otherwise it will cause the print head’s circuit board to be burned out. 1.When the print head is shipped, it will be coated with a protective liquid. When using it for the first time, wipe the print head before installing it. The protective liquid drops on the chip and where the ink bleeds. And use tissue to gently wipe the protective liquid on the chip (on the copper sheet). Don't use cleaning fluid or eraser. 2.During the regeneration process of the print head, the original ink will be cleaned and the protective liquid will be injected. If there is no protective liquid, printing will not be done when the pipeline is dry. If the print head can be detected, but color irregularity or blurry is observed, you can continue to add ink to print, print sheets to use up the protection liquid. And then the color can be used to print. 3. If the printing is not clear, press the cleaning button of the machine. And the print head can be cleaned when the ink cartridge is full of ink. If there is no ink to clean the print head, it is easy to be burn out. And you can print clearly after printing a few times. 4. Clean the print head directly on the machine instead using cleaning fluid. If you clean it with cleaning fluid and do not drop the protective fluid, the print head will be completely blocked and can not be used. 5. Don't use cleaning fluid or water to clean the print head, otherwise the print head will be completely blocked. When replacing the print head, please pay attention to the following items: 1.After receiving the print head, do not use a needle tube to inject water to check if the print head is blocked. It is a useless and dangerous practice. First of all, once the print head gets water and is not dry, and power on the machine, the main board will be burned out, and even the print head will be burned out. 2.The head surface of the print head is very fragile. It must not be touched, and needs to be protected. Its surface is an aluminum sheet, and inside is coated with a crystal oscillator and a very small ink tube. It will be deformed or even broken when touched, and the print head will be scrapped. 3.Be careful when installing the print head, be sure to cut off the power first, and install it in place. After installation, please push gently with your hands. Do not power on after installation, because if the head is not in place, the head will easily break when the machine moves. But your hands can feel, and it is easy to control. 4.When connecting the plug cable, do not be with ink. And make sure to make good contact with the socket and not touch the feet. Otherwise, it will cause the print head to short-circuit and burn. 5.The steel shaft should also be clean and smooth. Use tissue to stick some lubricating oil to wipe it off. Do not directly add oil to the shaft because excess oil will flow to the print head and cause damage. 6.After confirming that the machinery and circuit are normal, it is necessary to check the water circuit. First, check whether the amount of water in the ink cartridge is sufficient or not; second, check whether the small cleaning blade and the ink pump are dirty or not. 7.There will be air in the newly installed print head, so it will not print normally immediately. Only after the air in the print head is completely exhausted can the lines be printed normally. First of all, you can use the machine's cleaning function to perform intermittent cleaning (two cleanings each time,and then two more cleanings after a 30-minute pause). Excessive cleaning for many times will cause ink accumulation in the cleaning pump. It will not only cause color mixing and ink leakage, but also waste ink. 8.Secondly, you can print more pictures to let the print head exhaus En savoir plus Collaboration commerciale.

- - - - - - - - - - - - Product Description After purchasing and receiving the goods, please pay attention to the following items: NOTE: The power must be cut off before the Epson print head is installed, otherwise it will cause the print head’s circuit board to be burned out. 1.When the print head is shipped, it will be coated with a protective liquid. When using it for the first time, wipe the print head before installing it. The protective liquid drops on the chip and where the ink bleeds. And use tissue to gently wipe the protective liquid on the chip (on the copper sheet). Don't use cleaning fluid or eraser. 2.During the regeneration process of the print head, the original ink will be cleaned and the protective liquid will be injected. If there is no protective liquid, printing will not be done when the pipeline is dry. If the print head can be detected, but color irregularity or blurry is observed, you can continue to add ink to print, print sheets to use up the protection liquid. And then the color can be used to print. 3. If the printing is not clear, press the cleaning button of the machine. And the print head can be cleaned when the ink cartridge is full of ink. If there is no ink to clean the print head, it is easy to be burn out. And you can print clearly after printing a few times. 4. Clean the print head directly on the machine instead using cleaning fluid. If you clean it with cleaning fluid and do not drop the protective fluid, the print head will be completely blocked and can not be used. 5. Don't use cleaning fluid or water to clean the print head, otherwise the print head will be completely blocked. When replacing the print head, please pay attention to the following items: 1.After receiving the print head, do not use a needle tube to inject water to check if the print head is blocked. It is a useless and dangerous practice. First of all, once the print head gets water and is not dry, and power on the machine, the main board will be burned out, and even the print head will be burned out. 2.The head surface of the print head is very fragile. It must not be touched, and needs to be protected. Its surface is an aluminum sheet, and inside is coated with a crystal oscillator and a very small ink tube. It will be deformed or even broken when touched, and the print head will be scrapped. 3.Be careful when installing the print head, be sure to cut off the power first, and install it in place. After installation, please push gently with your hands. Do not power on after installation, because if the head is not in place, the head will easily break when the machine moves. But your hands can feel, and it is easy to control. 4.When connecting the plug cable, do not be with ink. And make sure to make good contact with the socket and not touch the feet. Otherwise, it will cause the print head to short-circuit and burn. 5.The steel shaft should also be clean and smooth. Use tissue to stick some lubricating oil to wipe it off. Do not directly add oil to the shaft because excess oil will flow to the print head and cause damage. 6.After confirming that the machinery and circuit are normal, it is necessary to check the water circuit. First, check whether the amount of water in the ink cartridge is sufficient or not; second, check whether the small cleaning blade and the ink pump are dirty or not. 7.There will be air in the newly installed print head, so it will not print normally immediately. Only after the air in the print head is completely exhausted can the lines be printed normally. First of all, you can use the machine's cleaning function to perform intermittent cleaning (two cleanings each time,and then two more cleanings after a 30-minute pause). Excessive cleaning for many times will cause ink accumulation in the cleaning pump. It will not only cause color mixing and ink leakage, but also waste ink. 8.Secondly, you can print more pictures to let the print head exhaust air during work. Third, if the mac En savoir plus Collaboration commerciale.

Souris sans fil souris sans fil 2,4 GHz défilement optique pour ordinateur po SH   Features: 1.100% brand new and high quality. 2.Supports Plug & Play - no drivers required. 3.2.4 GHz Bluetooth. 4.The USB receiver can be accommodated in the battery compartment. 5.Integrated battery saving function - automatic shutdown of the mouse when inactive. 6.Power supply: 2 x AAA batteries (not included). 7.Buttons With scroll wheel (2 buttons + 1 scroll wheel + 1 DPI button). 8.Receiving range: approx 10 meters. Specification: About 2.4G+Bluetooth dual-mode charging wireless mouse installation process: 2.4G mode 1.Plug the receiver into the USB port of the computer (The receiver is located at the bottom of the mouse, please pull it out with your hand and come out) 2. Wait about 20 seconds and then push the power switch to the 2.4G mode file, the connection can be used normally. Bluetooth mode: 1.First open the computer Bluetooth search, 2.Push the power switch to the Bluetooth mode 3.Then find (BT5.1Mouse or BluetoothMouse) on the device that supports Bluetooth 4. Click the pairing link, the link can be used normally after successful. mma About the dual-mode charging wireless mouse charging process: Plug the charging cable or data cable with microUSB2.0 interface into the microUSB2.0 charging interface of the mouse, and then plug the other end of the cable into the USB interface of the computer to charge the mouse. (Computer USB interface, mobile phone charger, mobile power supply can charge the A5 intelligent multi-mode mouse) When the mouse is charging, the blue light on the charging interface will always be on, and it will automatically turn off when fully charged. It will be full in about 3 hours. Compatible operating systems: Windows Vista, 7, 8, 10 or later | Mac OS 10.6 or later | Linux Our easy-to-use, reliable and wireless mouse is available in black, white or pink. The wireless ultra slim mouse will quickly convince you with its ergonomic shape, thanks to which you can handle the input device comfortably. Due to the dimensions, the mouse is ideal for mobile use in conjunction with a notebook / laptop. Work efficiently on your laptop or PC thanks to the smooth and precise tracking of mouse movements. The mouse has an energy saving function. This automatically switches the mouse off when it is inactive, which saves the batteries and extends the life of the mouse. Note: We have different types of products, you can choose which one you need. Package inclulding: 1x 2.4GHz ultra slim mouse 1x USB receiver Payment Nous n'acceptons que Paypal comme moyen de paiement. L'article sera envoyé dans 24 heures suivant le paiement reçu du lundi au vendredi, et les commandes reçues le samedi et le dimanche seront affichées le lundi suivant. Shipping Nous fournissons des choix multiples pour les méthodes d'expédition et la date d'arrivée estimée, mais veuillez comprendre que nous ne pouvons pas contrôler la condition d'expédition actuelle et la date d'arrivée. Terms of Sale Si vous n'êtes pas satisfait de votre achat, contactez-nous sans hésiter. Les articles peuvent être retournés dans 30 jours en état inutilisé, nous effectuerons un échange et un remboursement une fois que nous aurons reçu l'objet. Gardez les étiquettes entières et les éléments propres sans saveur, si non nous n'accepterons pas le retour. About US Si vous avez des questions, contactez-nous par l'intermédiaire de l'onglet «Demandez-nous un vendeur» au bas de la page d'inscription. Répondre à votre satisfaction est la chose la plus imotante pour nous, nous souhaitons résoudre chaque problème pour vous. Et laissez-nous une note de  5 étoiles  si vous vous sentez heureux de notre produit et service. Features: 1.100% brand new and high quality. 2.Supports Plug & Play - no drivers required. 3.2.4 GHz Bluetooth. 4.The USB receiver can be accommodated in the battery compartment. 5.Integrated battery saving function - automatic shutdown of the mouse when inactive. 6.Power supply: 2 x AAA batteries (not included). 7.Buttons With scroll wheel (2 buttons + 1 scroll wheel + 1 DPI button). 8.Receiving range: approx 10 meters. Specification: About 2.4G+Bluetooth dual-mode charging wireless mouse installation process: 2.4G mode 1.Plug the receiver into the USB port of the computer (The receiver is located at the bottom of the mouse, please pull it out with your hand and come out) 2. Wait about 20 seconds and then push the power switch to the 2.4G mode file, the connection can be used normally. Bluetooth mode: 1.First open the computer Bluetooth search, 2.Push the power switch to the Bluetooth mode 3.Then find (BT5.1Mouse or BluetoothMouse) on the device that supports Bluetooth 4. Click the pairing link, the link can be used normally after successful. mma About the dual-mode charging wireless mouse charging process: Plug the charging cable or data cable with microUSB2.0 interface into the microUSB2.0 charging interface of the mouse, and then plug the other end of the cable into the USB interface of the computer to charge the mouse. (Computer USB interface, mobile phone charger, mobile power supply can charge the A5 intelligent multi-mode mouse) When the mouse is charging, the blue light on the charging interface will always be on, and it will automatically turn off when fully charged. It will be full in about 3 hours. Compatible operating systems: Windows Vista, 7, 8, 10 or later | Mac OS 10.6 or later | Linux Our easy-to-use, reliable and wireless mouse is available in black, white or pink. The wireless ultra slim mouse will quickly convince you with its ergonomic shape, thanks to which you can handle the input device comfortably. Due to the dimensions, the mouse is ideal for mobile use in conjunction with a notebook / laptop. Work efficiently on your laptop or PC thanks to the smooth and precise tracking of mouse movements. The mouse has an energy saving function. This automatically switches the mouse off when it is inactive, which saves the batteries and extends the life of the mouse. Note: We have different types of products, you can choose which one you need. Package inclulding: 1x 2.4GHz ultra slim mouse 1x USB receiver PAYMENT Nous n'acceptons que Paypal comme moyen de paiement. L'article sera envoyé dans 24 heures suivant le paiement reçu du lundi au vendredi, et les commandes reçues le samedi et le dimanche seront affichées le lundi suivant. SHIPPING Nous fournissons des choix multiples pour les méthodes d'expédition et la date d'arrivée estimée, mais veuillez comprendre que nous ne pouvons pas contrôler la condition d'expédition actuelle et la date d'arrivée. Terms of Sale Si vous n'êtes pas satisfait de votre achat, contactez-nous sans hésiter. Les articles peuvent être retournés dans 30 jours en état inutilisé, nous effectuerons un échange et un remboursement une fois que nous aurons reçu l'objet. Gardez les étiquettes entières et les éléments propres sans saveur, si non nous n'accepterons pas le retour. ABOUT US Si vous avez des questions, contactez-nous par l'intermédiaire de l'onglet «Demandez-nous un vendeur» au bas de la page d'inscription. Répondre à votre satisfaction est la chose la plus imotante pour nous, nous souhaitons résoudre chaque problème pour vous. Et laissez-nous une note de  5 étoiles  si vous vous sentez heureux de notre produit et service. Le 24-sept.-20 à 13:01:00 Paris, le vendeur a ajouté les informations suivantes:

- - - - - - - - Product Description Before you buy this product, you need to pay attention to: NOTE: The printer must be disconnected from the power source before the print head is installed, otherwise it has the risk of causing the print head circuit board to burn out. 1. When the print head is shipped, a protective liquid will be applied to the print head. Before using it for the first time, wipe the print head before installing it.Just wipe the copper sheet gently, wipe it clean with soft paper, don't wipe it with cleaning fluid or eraser. 2. During the regeneration process of the print head, the ink will be cleaned and the protection liquid will be injected. If there is no protective liquid, the print head cannot print because the pipeline channel is dry.If the print head can be detected, but the colors are uneven or blurred, you can continue printing with ink. Print a few more sheets of paper and wait for the excess protection fluid to run out, then you can print normally 3. If the printing effect is not clear, press the machine cleaning button to clean (the print head must be cleaned only when the ink cartridge is sufficient, or it will burn out easily). 4. You don't need to clean the print head with cleaning fluid, you can clean the print head directly on the machine. If you clean the print head with the cleaning fluid(or water) and do not drop the protective fluid, the print head will be completely blocked, and it will be useless.   Before you install this product, you need to pay attention to: 1.After receiving the print head, if you use a needle tube to inject water to check the nozzle or see if it is blocked, this is a very redundant and dangerous behavior.If the printing effect is not clear, press the machine cleaning button (the pFirst of all, once the print head enters the water, if the water is not dry, it is powered on. The main board will be burned out, and the print head will be burnt out. Secondly, the print heads sold in our shop have been strictly tested and filled with protective liquid.If you use a needle to inject water into the print head, it will not only wash away the protective liquid in the head, but also easily cause air blockage in the print head, resulting in no ink. 2.Be careful when installing the print head, be sure to cut off the power first, and install it in place. 3.When connecting the plug cable, do not have ink on it, and make sure that it is in good contact with the socket. 4.The steel shaft should also be clean and smooth. You can use a paper towel to stick some lubricating oil to wipe it. Do not directly add oil to the shaft. The excess oil will flow to the print head and cause damage. 5.After the machinery and circuit are all correct, check the water circuit. Firstly, check whether the ink volume in the ink cartridge is sufficient; secondly, check whether the small cleaning blade and the ink suction pump are dirty. 6.There will be air in the newly installed print head, so it will not print normally immediately. The printer can only produce perfect results after the air in the head is completely discharged.You can use the machine's own cleaning function for intermittent cleaning(Clean 2 times each time, and then 2 times after 30 minutes) Repeated over-cleaning will cause ink accumulation in the cleaning pump, which will not only cause color mixing, ink leakage, and waste ink.Finally, you can print more pictures to let the print head exhaust air during work. Reufrbished 950 951 Printhead for Hp officejet pro 8100 8600 CM751 950 951 Printhead for Hp 8100 8600 8610 8620 8630 8640 251dw 276dw Feature: Excellent performance and high quality. Made of high-quality material, durable, firm and stable for us to use. This is a cleaned, thoroughly tested and sealed Printhead. Good stability, long lifespan. Full color function. This is Aftermarket Replacement Item But Not Genuine. Size:104x

Adaptateur de boîtier SSD USB Type C M.2 NVMe, Boîtier Externe en Aluminium SSD 10 Gbps USB 3.1 Gen 2, Conception d'aileron de Refroidissement Unique pour Une Bonne Dissipation de Chaleur Description du Produit Product name: Wanfocyu M.2 NVMe PCIe SSD Enclosure Interface type: M.2 NVMe PCIe to USB 3.1 Transfer Rate: Up to 10Gbps Product Size:111mm*43mm*11mm（4.37inch*1.7inch*0.44inch） Material: Aluminum Cable Type: USB3.1 USB-C to C& USB3.1 USB-C to A cables Support SSDs Drivers Size: 2230mm 2242mm 2260mm 2280mm Features: 1. USB 3.1 USB-C extreme fast and high-capacity data transfer solution, Data transfer rate up to 10Gbps for USB 3.1; 2. Supports NVMe PCIe-based M.2 SSDs; 3. Easy installation & no driver required, No additional power required; 4. Supports Plug & Play and Hot-Swapping; 5. Multi OS Supported, like Windows, Mac OS & Linux etc. Package Included: 1 x M.2 NVMe PCIe to USB 3.1 USB-C SSD Enclosure 1 x USB 3.1 USB-C to C cable 1 x USB 3.1 USB-C to A cable 1 x Screw Driver Please note that it only supports M.2 NVMe PCIe-based SSD only. We tested our enclosure with Samsung 970 EVO NVMe SSD, the actual speed can UP to 1000MB/s on R/W. But to this speed, pls make sure the Laptop TYPE C port is also comply with USB3.1 Gen 2(10Gbps), if USB3.1 Gen 1(5Gbps), then speed will be only half. For the brand new SSD drive, it may not be found, so please format it before the first time using. Pls format it to corresponding type which Windows and Mac supported. Follow step is to find the brand new ssd drive: 1. Use your mouse right key to click "Computer", it will show a drop-down menu; 2. Use your mouse left key to click "Computer Managment"; 3. Use your mouse left key to click "Disk Management"; 4. After find the brand new SSD drive, please format it, and made partition. Then you can find the drive normally. Haute vitesse: vitesse de transmission théorique USB3.1 10 Gbps; Capable d'atteindre des performances supérieures à 900 Mb / s en lecture / écriture avec un support NVMe hautes performances. Rétrocompatible avec USB 3.1 Gen 1 et USB 3.0 jusqu'à 5 Gbps Dissipation de la chaleur: conception de coque de dissipateur thermique interne brevetée pour une excellente dissipation de la chaleur, une consommation d'énergie réduite et la prévention de la surchauffe des disques SSD. Compatibilité; Uniquement pour NVMe m-key M.2 SSD (à base de camembert). ne prend pas en charge les disques SSD M.2 basés sur SATA (NGFF). applicable aux tailles 2230/2242/2260 / 2280. Supporte Samsung 950Pro / 960EVO / PM951 / PM961 / SM951 / SM961. Adoptez la puce principale JMS583: conforme à la norme UASP, qui peut améliorer efficacement la vitesse et prolonger la durée de vie du disque SSD. Compatible multi-OS, Windows 7/8/8.1/10/Linux/MAC. Magasinage sans risque: Nous sommes tellement convaincus que vous aimerez nos produits que nous offrons une garantie de remboursement à 100% avec une garantie d'un an.

Adaptateur de boîtier SSD USB Type C M.2 NVMe, Boîtier Externe en Aluminium SSD   Description Couleur: OWE1902 Product name: Wanfocyu M.2 NVMe PCIe SSD Enclosure Interface type: M.2 NVMe PCIe to USB 3.1 Transfer Rate: Up to 10Gbps Product Size:111mm*43mm*11mm（4.37inch*1.7inch*0.44inch） Material: Aluminum Cable Type: USB3.1 USB-C to C& USB3.1 USB-C to A cables Support SSDs Drivers Size: 2230mm 2242mm 2260mm 2280mm Features: 1. USB 3.1 USB-C extreme fast and high-capacity data transfer solution, Data transfer rate up to 10Gbps for USB 3.1; 2. Supports NVMe PCIe-based M.2 SSDs; 3. Easy installation & no driver required, No additional power required; 4. Supports Plug & Play and Hot-Swapping; 5. Multi OS Supported, like Windows, Mac OS & Linux etc. Package Included: 1 x M.2 NVMe PCIe to USB 3.1 USB-C SSD Enclosure 1 x USB 3.1 USB-C to C cable 1 x USB 3.1 USB-C to A cable 1 x Screw Driver Please note that it only supports M.2 NVMe PCIe-based SSD only. We tested our enclosure with Samsung 970 EVO NVMe SSD, the actual speed can UP to 1000MB/s on R/W. But to this speed, pls make sure the Laptop TYPE C port is also comply with USB3.1 Gen 2(10Gbps), if USB3.1 Gen 1(5Gbps), then speed will be only half. For the brand new SSD drive, it may not be found, so please format it before the first time using. Pls format it to corresponding type which Windows and Mac supported. Follow step is to find the brand new ssd drive: 1. Use your mouse right key to click "Computer", it will show a drop-down menu; 2. Use your mouse left key to click "Computer Managment"; 3. Use your mouse left key to click "Disk Management”; 4. After find the brand new SSD drive, please format it, and made partition. Then you can find the drive normally. Haute vitesse: vitesse de transmission théorique USB3.1 10 Gbps; Capable d'atteindre des performances supérieures à 900 Mb / s en lecture / écriture avec un support NVMe hautes performances. Rétrocompatible avec USB 3.1 Gen 1 et USB 3.0 jusqu'à 5 Gbps,Dissipation de la chaleur: conception de coque de dissipateur thermique interne brevetée pour une excellente dissipation de la chaleur, une consommation d'énergie réduite et la prévention de la surchauffe des disques SSD.,Compatibilité; Uniquement pour NVMe m-key M.2 SSD (à base de camembert). ne prend pas en charge les disques SSD M.2 basés sur SATA (NGFF). applicable aux tailles 2230/2242/2260 / 2280. Supporte Samsung 950Pro / 960EVO / PM951 / PM961 / SM951 / SM961.,Adoptez la puce principale JMS583: conforme à la norme UASP, qui peut améliorer efficacement la vitesse et prolonger la durée de vie du disque SSD. Compatible multi-OS, Windows 7/8/8.1/10/Linux/MAC.,Magasinage sans risque: Nous sommes tellement convaincus que vous aimerez nos produits que nous offrons une garantie de remboursement à 100% avec une garantie d'un an. About us Payment Nous acceptons Paypal Shipping Nous livrons sous 3-4 jours Return Les retours sont gratuits sous 30 jours Copyright © GetProduct.io 2020.

Ingelon Usb Flash 16gb 32gb 64gb 128gb Pendrive otg USB-C Type C Encrypted DIY LOGO microUSB Memory Stick for iphone IOS new cloud smartphone Specification: Item: 4in1 Flash Drive Installation: External Material: Metal Colors:Silver Net Weight: 30g Product Size: 45mm*45mm Product Type: 4in1 flash drive(USB,micro usb,iphone,OTG,Type-c,) Connectors: Lightning, Micro-USB, USB-C 4-in-1: Usb, Lightning 8-pin, Micro USB, USB Type C Note: Please download an APP " iUSB Pro " before you use this Flash Drive!!! Compatible with: For iPhone, Android & Type-C OTG USB Devices Support FAT32 & exFAT Compatible File Format: File: txt, doc, ppt, xls, xlsx, pdf Music: mp3, wma, wav, m4a, aac, m4r, ogg Video: mov, mpg, swf, vob, wmv, rmvb, avi, mp4, mkv, flv, 3gp, rm Image: jpg, jpeg, png, gif, bmp, tif, itff Computer Systems Supported: Windows XP / Vista / Win7 / Win10 / Mac OS 9.x and above / Linux 2.4.x Shipment: 1 Shipping address: We will ship according to the default address you give and please make sure the address is correct. Please kindly note there will be extra shipping cost if the address is remote one. All the goods, including free shipping, does not include the remote delivery cost. 2 Invoice: Please confirm detailed information about delivery invoice, like how much price we should write on delivery invoice, how much transportation charge we should write on invoice, how to descripe the goods etc. 3 Most orders will be shipped out within 3-5 business days upon payment confirmation. If there is any exception, we will keep you posted by leaving a message. 4 Shipper: "Free Shipping" item will be posted by China Post Air Mail / China Post Oridinary Mail, items can be checked and tracked online. Shipping normally takes 35 to 60 days. For the goods not free shipping or if there is any other requirement of the shipping, please contact the service for another choice just as DHL, UPS, Fedex etc. and the extra cost should be on buyer's side. 5 When receive the goods, please check whether the package is broken and the goods is OK. If there is broken caused by shipment, please take photo and ask the courier to sign. We will help to ask compensation for you. 6 Import duties, taxes and charges are not included in the item price or shipping charges. These charges are the buyer's responsibility. Please check with your country's customs office to determine what these additional costs will be prior to bidding/buying. Other Policies: 1 We are not responsible for any custom duty or import tax. 2 We will leave POSITIVE FEEDBACK after receiving your payment. Please contact us if you are not satisfied with the item after receiving it. 3 All emails will be answered within 24 hours. If you do not receive our reply, please kindly resend your email and we will reply to you as soon as possible. 4 Serious Buyer Only! Please place order only if you agree with all the terms. FAQ: Q: How do I pay for my purchase? A: we accept the following payment methods: credit card; alipay,Paypal. Q: Is there any tracking Number for my item? A: Yes, we ship every order with their Tracking Number, and you can view the shipment staus on the corresponding website. Q: Does this product come with retail package? A: We have declared the packing detail on the description of each product, please check it, thank you! Q: I am a reseller,I would like to buy many pieces of your item, what's the wholesale price? A: Hi,thanks for your inquiry first, if you would like to buy large quantity, please contact me in advance,if there is big space for us to build business relationship in the coming future, we will give you the best price, thanks! Feedback: We are an honest seller on Aliexpress. All our items come from China with high quality. If you have any problem after receive the products, please contact us immediately. Feedback is important to us, please take time to leave a positive feedback if you are satisfied with our product and service. We guarentee to do the same for you. Thank you for giving us a chance to make things right by good communication.

Product feature:   2.4 GHz wireless connection (including USB receiver and rechargeable mouse USB cable). The capacity of the built-in rechargeable battery can reach 600mA. Ergonomic design, can prevent and prevent carpal tunnel syndrome. Precision controlled optical laser technology. User convenience, wow pen signature, comfortable backrest. L / R mouse button, 2 thumb buttons and a click wheel, feed, retreat, dpi. You choose the most suitable for your hand. Plug and play, compatible with Mac and PC. 7 colors of breathing light to give users cool gaming experience.       Product specifications:   Type of project: ergonomic optical mouse. 2400 dpi resolution. Maximum working range: 10 m. Charging cable length: 50 cm. Color: black, white and gray  Material: ABS. Battery capacity: 600mAh. Button click life: 10 million times. Rated voltage / current: DC 3.7V / 18mA. System requirements: Windows 98 / Me / 2000 / XP / Vista / Win 7 / Win8 / 10 / Vista Mac OS or latest. Product weight: 103g. Item size: 76 * 135 * 42mm.       Charge step:   Plug one end of the Android charging line into the mouse charging connector and the other end into the charging port with the usb port. When charging, the power is disconnected at the on speed to charge normally. The mouse is plugged into the usb receiver, the blue light is bright when charging, indicating the blue lamp flashes when the charge is almost full. The blue lamp went out after the electricity was full. Charging time is 6-8 hours, do not use when turn off the mouse switch!     Package Included:   1 x Mouse. 1 x USB power adapter. 1 x USB charging cable. 1 x user manual.  

ETEPON pour écran Raspberry Pi 4, Moniteur Tactile Capacitif HDMI de 7 Pouces Écran LCD 1024 * 600 HD La description ETEPON Capacitive Touch LCD Display HDMI Input 1024× 600 with Case Stand for 7 Inch Raspberry Pi Screen when the 7 inch Touch Screen work with the Raspberry Pi, it supports the Raspbian, Ubuntu, Win10 IoT, single-touch and free drive, When using as a computer monitor, It supports Windows 10/ 8. 1/ 8/ 7, five point touch and free drive. ✔ Feature: LCD ✔ Size: 7. 0 inch (diagonal)driver ✔ Element: a-si TFT active matrix ✔ Display mode: normally White, transmissive high ✔ Resolution: 1152, 000 dots (800 x 3(rgb) x 480) ✔ SSD1963 touch panel controller Dot pitch: 0. 0642(W) x 0. 1790(H)mm. ✔ Ctive area: 154. 08(W)x 85. 92(H) module ✔ Size: 164. 9(W)x100. 0(H)x5. 7(D)mm surface ✔ Treatment: anti-glare ✔ Color arrangement: rgb-stripe ✔ Interface: digital ✔ Backlight: highlighted LED lamp backlighting ✔ TFT power(pin name: 3. 3V): The power of the screen is 2. 8-3. 3V; not use 5V, all the pin's voltage on the module can not be more than 3. 3V. ✔ Backlight power supply (pin name: 5V): backlight power range is 4. 5-7V. ✔ Interface Type: 16 parallel operating ✔Temperature: -20 70 degrees centigrade storage ✔Temperature: -30 80 degrees centigrade package includes: 1x 7inch HDMI LCD (B) 1x HDMI cable 1x USB Type A plug to Micro B plug cable 1x rpi screws Pack (4PCs) 1x protective case Features: ☺► Commande tactile capacitive ► La résolution de cet écran Raspberry Pi est de 1024 × 600. Elle comporte également une fonction de basculement vertical et horizontal. Image 4: Conversion du format d'affichage 3/16: 9 ☺► Tension de fonctionnement ► L'écran tactile 5V 1a exige le courant requis dans le régulateur 2a ci-dessus, un régulateur de suralimentation intégré 400mA CC-CC pour fournir une alimentation électrique au rétroéclairage de l'écran LCD ☺►Multifonctionnel ► lorsque l'écran tactile de 7 pouces fonctionne avec le Raspberry Pi, il prend en charge les lecteurs Raspbian, Ubuntu, Win10 IoT, à touche unique et libre. Lors de l'utilisation en tant qu'écran d'ordinateur, il prend en charge Windows 10 / 8. 1/8/7, tactile cinq points et lecteur libre ☺► avec étui de protection ► l'écran Raspberry Pi est fourni avec le support réglable pour l'étui de protection, fabriqué en acrylique noir. Un tableau Raspberry Pi peut être installé à l'arrière de l'étui Better► Meilleur service client ► Si vous avez besoin d'assistance technique, merci de nous le signaler, nous serons certainement responsables de tout problème ou vous pouvez vous adresser au contrôle qualité, il vous suffit de nous retourner pour un remboursement complet dans les 30 jours Product Details: Marque: ETEPON Numéro du modèle de l'article: EP711 Couleur: Blanc, Noir Type d'écran: LCD Taille de l'écran: 7 Pouces Resolution: 1080p Full HD Interface du matériel informatique: USB, HDMI Nombre de ports HDMI: 1 Type de connecteur: USB Type-A, HDMI Dimensions de l'article L x L x H: 18.8 x 12.7 x 1.9 centimètres Poids du produit: 499 Grammes Journées de manutention Nous expédierons toutes les commandes dans 1 jour ouvrable de paiement. Livraison Nous ne livrons pas en dehors de la France continentale. Politique de retour Tous les articles sont admissibles pour les retours dans les 60 jours suivant la réception. L'acheteur est responsable de l'expédition de retour sur n'importe quel article qui n'est pas endommagé. Évaluations Nous prenons notre réputation au sérieux, nous achetons et vendons en ligne, donc nous comprenons la valeur de la confiance. Si vous n'êtes pas satisfait de votre commande, veuillez nous contacter et nous travaillerons avec vous pour le résoudre à votre satisfaction.

Bonjour, Vends Carte graphique ATI Radeon X850 XT PE (Platinum Edition) de marque Sapphire. Attention il s'agit de la version avec connecteur AGP 8x. La carte fonctionne normalement. Le système de refroidissement a été démonté il y a quelques années pour remplacer la pâte thermique, la carte n'a pas vraiment été beaucoup utilisée depuis. Il manque 2 vis (visible sur les photos) mais tout est solidement fixé. Carte vendue dans sa boîte d'origine avec toutes les connectiques, fascicule, CD de pilotes.  Envoi en France via Mondial Relay à 3,95€ ou via Colissimo à 9,15€ ________________ English version: Hello, Selling ATI Radeon X850 XT PE (Platinum Edition) video card from Sapphire. Caution: It is the version with an AGP 8x connector. The card works normally. The cooling system has been taken out a few years ago to replace the thermal compound and the card hasn't seen a lot of use since then. There are 2 screws missing (visible in the pictures) but everything is firmly attached. The card is sold with its original box, cables, booklet and drivers CD. Shipping to the EU with La Poste Colissimo for 18,05€ and to the UK for 21,05€

- Print head QY6-0073 For IP3600 MP558 568 MX868 MX870 MX878 MG5140 5180 CE 26.99 USD Free shipping - Full Color QY6-0072 Printhead Printer Head for iP4600 iP4680 iP4700 iP4760 CE 35.99 USD Free shipping - Full Color QY60078 Printhead Printer Head for MG6220 6140 6180 6100 6150 6200 CE 43.99 USD Free shipping - Replacement Printer Print Head QY6-0050 For 900PD I900D I950D IP6100D IP6000D CE 25.99 USD Free shipping - QY6-0055 Printhead Printer Head for i9900 iP8500 i9950 ip9100 PRO9000 CE 68.99 USD Free shipping - 950 951 Print head For CM 751 752 Hp 8100 8600 8610 8620 8630 8640 251dw CE 145.99 USD Free shipping - Printhead QY6-0083 Fit For iP8720 iP8750 iP8780 MG7520 MG7180 inkjet printer CE 39.99 USD Free shipping - Colors QY6-0076 Printhead Printer Head for i9900 I9950 Pro900 9900i Mark II AF 91.99 USD Free shipping - Replacement Printer Print Head Full Color QY6-0068 Fits PIXMA iP100 IP110 ZA CE 46.99 USD Free shipping - PrintHead for HP 932 933 XL OfficeJet 7110 7610 6600 6100 e 6700 7612 CB863 T CE 43.49 USD Free shipping - Printhead Printer Head for Kodak 30 ESP Office 2100 / 2150 /2170 Hero 3.1/4.2 CE 22.99 USD Free shipping - Replacement Printer Print Head QY6-0090 For TS8020 TS9020 TS8040 8050 8070 CE 49.99 USD Free shipping - 934 935 Printhead Fit HP Officejet Pro 6230 6830 6815 6812 6835 CQ163-80060 CE 36.99 USD Free shipping - 952 955 Printhead for HP Officejet Pro 8710 8216 7740 7720 8720 8730 8740 CE 85.99 USD Free shipping - 4Color Printhead For HP 862/564 Photosmart B110A B210A B109A B109N C410A CE 23.49 USD Free shipping - Replacement Printer Print Head Printhead QY6-0059 For IP4200 MP500 MP530 CE 31.99 USD Free shipping - - - - - - - - - - - Product Description Before you buy this product, you need to pay attention to: NOTE: The printer must be disconnected from the power source before the print head is installed, otherwise it has the risk of causing the print head circuit board to burn out. 1. When the print head is shipped, a protective liquid will be applied to the print head. Before using it for the first time, wipe the print head before installing it.Just wipe the copper sheet gently, wipe it clean with soft paper, don't wipe it with cleaning fluid or eraser. 2. During the regeneration process of the print head, the ink will be cleaned and the protection liquid will be injected. If there is no protective liquid, the print head cannot print because the pipeline channel is dry.If the print head can be detected, but the colors are uneven or blurred, you can continue printing with ink. Print a few more sheets of paper and wait for the excess protection fluid to run out, then you can print normally 3. If the printing effect is not clear, press the machine cleaning button to clean (the print head must be cleaned only when the ink cartridge is sufficient, or it will burn out easily). 4. You don't need to clean the print head with cleaning fluid, you can clean the print head directly on the machine. If you clean the print head with the cleaning fluid(or water) and do not drop the protective fluid, the print head will be completely blocked, and it will be useless.   Before you install this product, you need to pay attention to: 1.After receiving the print head, if you use a needle tube to inject water to check the nozzle or see if it is blocked, this is a very redundant and dangerous behavior.If the printing effect is not clear, press th

- 920 Testina Di Stampa Printhead Per Hp 6500 6500A 7000 7500A B210A Cd868-30002 46.79 EUR Free shipping - 14N0700 Testina di stampa Printhead per Lexmark Pro805 Pro205 209 S408 S505 IT 49.19 EUR Free shipping - Testina di stampa per iP8720 iP8750 iP8780 MG6310 MG7520 MG7180 QY6-0083 56.39 EUR Free shipping - 934 935 Testina di stampa Printhead per HP Pro 6230 6830 6815 6812 6835 G 56.39 EUR Free shipping - F173030 Testina Di Stampa Printhead Per 1390/1400/1410/1430/1500W Y1 182.39 EUR Free shipping - QY6-0072 Testina di stampa Printhead per iP4600 iP4680 iP4700 iP4760 MP630 52.79 EUR Free shipping - Testina di stampa stampante per L300 L303 L351 L355 L358 L111/120 L211 NEW 67.19 EUR Free shipping - Testina di stampa stampante per HP 932XL OfficeJet 7110 7610 7612 7600 6060 6100 63.59 EUR Free shipping - 564 Testina Di Stampa Printhead Per Photosmart 7510 7515 7520 7525 Cb326-30002 39.59 EUR Free shipping - QY6-0089 Testina di stampa Printhead per TS5080 6020 6050 6051 6052 TS6080 R0 61.19 EUR Free shipping - QY6-0055 Testina di stampa Printhead per Canon i9900 iP8500 i9950 ip9100 PRO9000 85.19 EUR Free shipping - PrintHead per iP7220 iP7250 IP7240/7210 MG5420/5422/5450/6400 QY6-0082 New 56.39 EUR Free shipping - Testina di stampa Printhead Office 2100 / 2150 / 2170 Hero 3.1 / 4.2 41.99 EUR Free shipping - Testina di stampa per IP3600 iP3680 MP560 MP540 MP620 MX860 MX870 MG5140 45.59 EUR Free shipping - Testina di stampa stampante per HP 862/564 B110A B210A B109A B109N C410A C309A 44.39 EUR Free shipping - QY6-0059 Testina di stampa Printhead per IP4200 MP500 MP530 IT 50.39 EUR Free shipping - 952 955 Testina di stampa Printhead per HP Pro 8710 8216 8720 8730 8740 8210 G 98.39 EUR Free shipping - Testina di stampa Print Head 6 Colors per TX800 TX820 A800 F192040 146.39 EUR Free shipping - QY6-0078 Testina di stampa Printhead per MG6220 6140 6180 6100 6150 6200 61.19 EUR Free shipping - CN688A Testina di stampa Printhead per HP 3070 3520 3525 5525 4620 5520 5510 IT 41.99 EUR Free shipping - - - - - - - - - - - - - - - - - - - - Product Description Before you buy this product, you need to pay attention to: NOTE: The printer must be disconnected from the power source before the print head is installed, otherwise it has the risk of causing the print head circuit board to burn out. 1. When the print head is shipped, a protective liquid will be applied to the print head. Before using it for the first time, wipe the print head before installing it.Just wipe the copper sheet gently, wipe it clean with soft paper, don't wipe it with cleaning fluid or eraser. 2. During the regeneration process of the print head, the ink will be cleaned and the protection liquid will be injected. If there is no protective liquid, the print head cannot print because the pipeline channel is dry.If the print head can be detected, but the colors are uneven or blurred, you can continue printing with ink. Print a few more sheets of paper and wait for the excess protection fluid to run out, then you can print normally 3. If the printing effect is not clear, press the machine cleaning button to clean (the print head must be cleaned only when the ink cartridge is sufficient, or it will burn out easily). 4. You don't need to clean the print head with cleaning fluid, you can clean the print head directly on the machine. If you clean the print head with the cleaning fluid(or water) and do not drop the protective fluid, the print head will be completely blocked, and it will be useless. Before you install this product, you need to pay attention to: 1.After receiving the print head, if you use a needle tube to inject water to check the nozzle or see if it is blocked, this is a very redundant and dangerous behavior.If the printing effect is not clear, press the machine cleaning button (the pFirst of all, once the print head enters the water, if the water is not dry, it is powered on. The main board will be burned out, and the pr En savoir plus Collaboration commerciale.